Tripp Lite APSX2012SW Handleiding

Tripp Lite Niet gecategoriseerd APSX2012SW

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite APSX2012SW (48 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/48

Owner’s Manual

Sine Wave DC-to-AC Inverter/Chargers

Models: APSX1012SW, APSX2012SW

12VDC to 230VAC

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

Table of Contents

Important Safety Instructions 2

1. Overview & Features 3

1.1 Overview 3

1.2 Indicators, Controls and Settings 3

1.3 Optional Features 6

2. Battery Charger 6

2.1 Mode of Operation 6

2.2 Transfer Switching Speed 6

3. Battery Installation

and Maintenance 6

3.1 Select Battery Type 6

3.2 Monthly Maintenance 8

3.3 Battery Installation 8

3.4 Battery Connection 8

4. Inverter/Charger

Installation and Operation 10

4.1 Installation 10

4.2 Installation Diagrams and Charts 10

4.3 Installation and Start-Up 11

5. Technical Speciﬁcations 11

6. Troubleshooting 12

7. Service 12

Español 13

Français 25

Ðóññêèé 37

201110117 93-3054.indb 1 11/9/2011 10:57:55 AM

Important Safety Instructions

SAVE THESE INSTRUCTIONS!

This manual contains important instructions and warnings that should be followed during the installation,

operation and storage of all Tripp Lite Inverter/Chargers.

Location Warnings

• Install your Inverter/Charger in a location or compartment that minimizes exposure to heat, dust, direct sunlight and

moisture. Flooding the unit with water will cause it to short-circuit and could cause personal injury due to electric shock.

• For proper ventilation, allow a minimum 2 inches of clearance at front and back of the Inverter/Charger. To avoid overheating

the Inverter, the compartment that houses the Inverter/Charger must be properly ventilated with adequate outside air ﬂow.

The heavier the load of connected equipment, the more heat will be generated by the unit.

• Do not install the Inverter/Charger near magnetic storage media, as this may result in data corruption.

• Do not install the Inverter/Charger near ammable materials, fuel or chemicals.

Battery Connection Warnings

• Multiple battery systems must be comprised of batteries of identical voltage, age, amp-hour capacity and type.

• Because explosive hydrogen gas can accumulate near batteries if they are not well ventilated, do not install batteries in a

“dead air” compartment. The battery compartment should have some ventilation to outside air.

• Sparks may result during nal battery connection. Always observe proper polarity as batteries are connected.

• Do not allow objects to contact the DC input terminals. Do not short or bridge these terminals together. Serious personal

injury or property damage could result.

Ground Connection Warnings

• Safe operation requires connecting the Inverter/Charger’s Main Ground Terminal directly to the frame of the vehicle or

earth ground.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause

the failure of the life support equipment or to signicantly affect its safety or effectiveness is not recommended. Do not

use this equipment in the presence of a ammable anesthetic mixture with air, oxygen or nitrous oxide.

• You may experience uneven performance results if you connect a surge suppressor, line conditioner or UPS system to the

output of the Inverter/Charger.

• User must supply proper protection for wire openings in unit panels.

Operation Warnings

• Your Inverter does not require routine maintenance.

• Potentially lethal voltages exist within the Inverter/Charger as long as the battery supply is connected. During any service

work, the battery supply should therefore be disconnected.

• Do not connect or disconnect batteries while the Inverter/Charger is operating from the battery supply. Dangerous arcing

may result.

201110117 93-3054.indb 2 11/9/2011 10:57:55 AM

321 4 5 6 7 8 9

10 11

1. Overview and Features

1.1 Overview

• Tripp Lite’s Sine Wave Inverter-Charger is a heavy-duty unit generating a pure sine wave from a 12V battery bank. It can

supply power to a wide range of connected equipment, from heaters, air conditioners, refrigerators and vacuum cleaners to

computers and peripheral devices. It is designed to work in heavy load conditions, so de-rating is unnecessary.

• The smart charger is compatible with various battery types and sizes. The switch module automatically diverts the energy

transfer path between the inverter and an AC input. When the AC source is lower than the transfer level, the path switches

to the inverter. Otherwise, the load is powered by the AC input.

1.2 Indicators, Controls and Settings

1.2.1 Controls and LED Indicators

Shown below are the control panel and indicator lights on the front panel of the Inverter/Charger.

1 Power ON/OFF Button

2 LED 1 – DC Mode Inverter

3 LED 2 – AC Mode Charger

4 LED 3 – Inverter Condition

5 LED 4 – Battery Limits

6 LED 5 – 25% Battery Voltage

7 LED 6 – 50% Battery Voltage

8 LED 7 – 75% Battery Voltage

9 LED 8 – 100% Battery Voltage

Battery Temperature Port (RJ11)

Communication Port (RJ45)

201110117 93-3054.indb 3 11/9/2011 10:57:55 AM

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	APSX2012SW
Kleur van het product:	Grijs
Gewicht:	22450 g
Breedte:	228.6 mm
Diepte:	571.5 mm
Hoogte:	190.5 mm
Gewicht verpakking:	25360 g
Breedte verpakking:	294.6 mm
Diepte verpakking:	307.3 mm
Hoogte verpakking:	662.9 mm
Materiaal behuizing:	Staal
LED-indicatoren:	Ja
Aan/uitschakelaar:	Ja
Land van herkomst:	Taiwan
Geluidsalarm(en):	Ja
Ingangsspanning:	230 V
Uitgangsvermogen:	2000 W
Soort voeding:	Binnen
Stroomspanning bescherming:	Overbelasting
Frequentie:	50 Hz
Output current:	15 A
Spanning:	230 V
Piekvermogen:	4000 W
(Buitenste) hoofdverpakking hoogte:	662.9 mm
(Buitenste) hoofdverpakking breedte:	294.6 mm
(Buitenste) hoofdverpakking brutogewicht:	25360 g
(Buitenste) hoofdverpakking lengte:	307.3 mm
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Code geharmoniseerd systeem (HS):	8504.40.9570
Output frequentie:	50 Hz
Instelbare uitgangsspanning:	Ja
Power huidig type:	AC1-to-AC2