Triax TMS 916 CE P Handleiding

Triax Schakelaar TMS 916 CE P

Lees hieronder de 📖 handleiding in het Nederlandse voor Triax TMS 916 CE P (7 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/7
Series
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX SE A-
SE A-
SE A-
SE A- SE A-EU
EU
EU
EUEU
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX SE P-
SE P-
SE P-
SE P- SE P-
EU
EU
EU
EUEU
Si
Si
Si
SiSingle, w/P
ngle, w/P
ngle, w/P
ngle, w/Pngle, w/PSU and EU
SU and EU
SU and EU
SU and EUSU and EU Mains plu
Mains plu
Mains plu
Mains plu Mains plug, 8-32 out
g, 8-32 out
g, 8-32 out
g, 8-32 outg, 8-32 out, active TE
, active TE
, active TE
, active TE, active TER
R
R
R R
Si
Si
Si
SiSingle, w/P
ngle, w/P
ngle, w/P
ngle, w/Pngle, w/PSU and EU
SU and EU
SU and EU
SU and EUSU and EU Mains plu
Mains plu
Mains plu
Mains plu Mains plug, 8-32 out
g, 8-32 out
g, 8-32 out
g, 8-32 outg, 8-32 out, passive TE
, passive TE
, passive TE
, passive TE, passive TER
R
R
R R
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX SE P-R
SE P-R
SE P-R
SE P-R SE P-R
Single, n
Single, n
Single, n
Single, nSingle, no PSU, for S
o PSU, for S
o PSU, for S
o PSU, for So PSU, for SAT rece
AT rece
AT rece
AT receAT receiver DC s
iver DC s
iver DC s
iver DC siver DC sourcing, 8-32
ourcing, 8-32
ourcing, 8-32
ourcing, 8-32ourcing, 8-32 out, passiv
out, passiv
out, passiv
out, passiv out, passive TER
e TER
e TER
e TER e TER
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX CE A-
CE A-
CE A-
CE A- CE A-EU
EU
EU
EUEU
Cascade
Cascade
Cascade
CascadeCascade, for exte
, for exte
, for exte
, for exte, for external PSU, 8
rnal PSU, 8
rnal PSU, 8
rnal PSU, 8rnal PSU, 8-
-
-
-- out, acti
out, acti
out, acti
out, acti out, active TER
ve TER
ve TER
ve TERve TER
32
32
32
3232
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX CE P-
CE P-
CE P-
CE P- CE P-EU
EU
EU
EUEU
Cascade
Cascade
Cascade
CascadeCascade, for exter
, for exter
, for exter
, for exter, for external PSU, 8
nal PSU, 8
nal PSU, 8
nal PSU, 8nal PSU, 8-32 out, pas
-32 out, pas
-32 out, pas
-32 out, pas-32 out, passive TE
sive TE
sive TE
sive TEsive TER
R
R
R R
Language
Language
Language
LanguageLanguage
EN
EN
EN
ENEN
Version:
Version:
Version:
Version:Version: 9.2016.A
9.2016.A
9.2016.A
9.2016.A 9.2016.A
User Guide
TMS 9XX SE/CE Euro Line Multiswitch Series
EN
2
Triax Euro Line TMS 9XX SE/CE Multiswitch
The Triax Euro Line Multiswitch Range is a very high quality range of Multiswitches for single or cascade SAT- IF
(satellite) distribution networks with a need for RF loop-through. Available in both active and passive variants for RF
loop-through the range offers a perfect selection to use for both terrestrial aerial reception signals (A-active), as well
as a full CATV signal including DOCSIS support (P-passive). NOTE, DOCSIS limited by SAT-IF that occupies 950-
2150MHz.
The Euro Line Series is Made in Europe, and fully meets the EN 50083-3 Class A shielding requirements.
The purpose of this guide is to enable the successful installation and use of the TMS 9XX Multiswitch series.
The TMS 9XX Series (Two satellite positions):
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX SE P-EU
SE P-EU
SE P-EU
SE P-EU SE P-EU = Stand-alone unit, terrestrial passive, built-in PSU with EU Mains plug.
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX SE A-
SE A-
SE A-
SE A- SE A-EU
EU
EU
EUEU
=
=
=
= = Stand-alone unit, terrestrial active, built-in PSU with EU Mains plug.
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX SE P-R
SE P-R
SE P-R
SE P-R SE P-R = Stand-alone unit, terrestrial passive. No PSU.
Power sourced from the SAT-Receivers. Optionally an external PSU can be is
added. This Version has no T-Active option avoid too much power to
consumption from connected SAT-receiver(s).
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX CE P
CE P
CE P
CE P CE P = Cascaded output unit, terrestrial passive, for external PSU.
TMS 9XX
TMS 9XX
TMS 9XX
TMS 9XXTMS 9XX CE A
CE A
CE A
CE A CE A = Cascaded output unit, terrestrial active, for external PSU.
NOTE
NOTE
NOTE
NOTENOTE: The TMS 9XX Range uses two Quattro LNBs each receiving from one orbital Satellite position.
XX
XX
XX
XXXX are placeholder for individual units with 08, 12, 16, 24 or 32 user/subscriber outputs.
Please
Please
Please
PleasePlease refer to Triax.c
refer to Triax.c
refer to Triax.c
refer to Triax.c refer to Triax.com for Euro Ser
om for Euro Ser
om for Euro Ser
om for Euro Serom for Euro Series Multiswit
ies Multiswit
ies Multiswit
ies Multiswities Multiswitch product
ch product
ch product
ch productch products for reception o
s for reception o
s for reception o
s for reception os for reception of
f
f
f f 1, 3 a
1, 3 a
1, 3 a
1, 3 a1, 3 and 4 SAT pos
nd 4 SAT pos
nd 4 SAT pos
nd 4 SAT posnd 4 SAT positions
itions
itions
itionsitions
Security
During installation please observe the requirements set forth in the EU safety standards EN 60065 and
50083-1 as well as local requirements and standards for SAT-IF and RF SMATV-installations.
Exercise care and good practise when mounting coaxial connectors (F-connectors) on the cables to
avoid short circuits and unnecessary emission of noise and disturbance of neighbouring installations.
Only perform multi switch installation jobs while mains plug of all power supplies are disconnected.
Make sure no short circuits are present on the distribution cables before applying mains power to the
multi switch installation and Satellite Receivers. Short circuits may overload, overheat and harm Power
Supplies and Satellite Receivers that are attempting to supply an excessive amount of current.
Check the rating labels of any attached power supply and make sure the local Mains Voltage you
connect it to never exceeds those ratings. Failure to observe this and act accordingly may compromise
the security and safety of the whole system and expose you and everyone attached to the installation to
damage, fire and electric shock.
Make sure the ambient temperature at the installation site never exceeds the temperature limits for the
product installed. If required you must arrange for suitable temperature conditioning. Failure to observe
this and act accordingly may compromise the performance, security and safety of the whole system and
expose you and everyone attached to the installation to damage, fire and electric shock.
A multi switch installation should be earthed. An earth screw is available on the multi switch unit.
The manufacturer is not responsible for damage or system failures caused by Installers ignoring the
above safety measures.
Installation:
First rule in any Multiswitch installation are: NEVE
NEVE
NEVE
NEVENEVER
R
R
RR use a too small size satellite Dish, and
NEVER
NEVER
NEVER
NEVERNEVER use the compromise of a dual mount LNB for a multi satellite position reception on one Dish.
Correct Dish size ensures sufficient reserves in bad weather and the best possible C/N for the rest of the
installation. Making compromises here CANNOT be fixed later in the network by adding Amplifiers!
A High Gain LNB only gives more Signal Level, but not Signal Quality. That only comes from Dish Size!
Mount the multi switch only indoor on a vertical dry surface using the available screwholes and ‘feets’.
Make sure that no supply voltage is available on the connection cables during installation.
(Temporarily turn off satellite receivers and/or their LNB supply).
Mount suitable F-connectors on the coax cable going to the satellite receivers and connect them
individually to a multi switch subscriber output (8 to 32 outputs dependent on type). Recommended
maximum cable length from switch to receiver is typically 25-35 meters depending upon cable
type/quality and satellite receiver. Far longer cable runs are possible, but be aware of possible DiSEqC
switching problems which may vary between satellite receivers.
Mount suitable F-connectors on the coax cable coming from the LNB units (or another cascaded
Multiswitch unit). Connect them to the correct inputs of the multi switch. Observe correct colour coding.
Double-check that correct SAT polarities are connected to correct multiswitch inputs.
Preferably use a suitable outlet socket in the apartment at the satellite receiver to separate the terrestrial
RF and satellite SAT-IF signals (e.g.: TOU 01S, EDA 302 F). NOTE: The SAT outlet must have DC pass.
Outputs on the multi switch not in use should be terminated with DC-blocked 75 ohm terminators.
DC supply for LNBs and/or Line Amplifier(s) can be done via the built-in PSU (P-EU and A-EU versions)
and can be done by attaching an external power supply to any of the TMS 9XX CE cascade units.
Cascade switches can also take DC Supply from the trunk lines if a PSU is connected elsewhere in the
trunk. Please consider total system power consumption requirements and add PSUs as needed. DC-
block s may need to be inserted to avoid power supply conflicts. er
The switch itself only needs a receiver to work on SAT-IF (Active A-versions needs a PSU for RF to work).
Apply mains power to the installation power supply(es) only when all connections are done and you are
sure there are no short circuits present on the coax cables (use a multi-meter to check and verify).
Satellite receivers can now be connected, turned on and set up. System is ready for use.
BEWARE
BEWARE
BEWARE
BEWAREBEWARE: A high Signal Level does not guarantee the digital quality of your signal! Make sure to use a
suitable quality Field Strength Measurement Instrument that lets you keep track of, and ensure suitable
C/N, BER and MER Levels throughout the network.
Multiswitch colour coding layout for LNB inputs and outputs:
Type
Type
Type
Type Type
BAND
BAND
BAND
BAND BAND
Polarity
Polarity
Polarity
Polarity Polarity
Switch
Switch
Switch
SwitchSwitch voltage
voltage
voltage
voltage voltage
Switch
Switch
Switch
SwitchSwitch freq.
freq.
freq.
freq. freq.
Colour co
Colour co
Colour co
Colour coColour coding
ding
ding
ding ding
SAT
SAT
SAT
SAT SAT
High Ban
High Ban
High Ban
High BanHigh Band
d
d
d d
Horisont
Horisont
Horisont
HorisontHorisontal
al
al
al al
18 V DC
18 V DC
18 V DC
18 V DC 18 V DC
22 kHz
22 kHz
22 kHz
22 kHz 22 kHz
Yellow
Yellow
Yellow
Yellow Yellow
Vertical
Vertical
Vertical
Vertical Vertical
13 V DC
13 V DC
13 V DC
13 V DC 13 V DC
22 kHz
22 kHz
22 kHz
22 kHz 22 kHz
Red
Red
Red
Red Red
Low Ban
Low Ban
Low Ban
Low BanLow Band
d
d
d d
Horisont
Horisont
Horisont
HorisontHorisontal
al
al
al al
18 V DC
18 V DC
18 V DC
18 V DC 18 V DC
0 kHz
0 kHz
0 kHz
0 kHz 0 kHz
Green
Green
Green
Green Green
Vertical
Vertical
Vertical
Vertical Vertical
13 V DC
13 V DC
13 V DC
13 V DC 13 V DC
0 kHz
0 kHz
0 kHz
0 kHz 0 kHz
Black
Black
Black
Black Black
TER
TER
TER
TER TER
NA
NA
NA
NANA
White
White
White
White White

Product specificaties

Merk: Triax
Categorie: Schakelaar
Model: TMS 916 CE P

Heb je hulp nodig?

Als je hulp nodig hebt met Triax TMS 916 CE P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Schakelaar Triax

Triax

Triax TMS 916 CE P Handleiding

5 April 2024
Triax

Triax TMS 932 CE Handleiding

5 April 2024

Handleiding Schakelaar

Nieuwste handleidingen voor Schakelaar

Smart-AVI

Smart-AVI SM-DVN-2D Handleiding

21 December 2024
Smart-AVI

Smart-AVI SM-DPN-2Q Handleiding

21 December 2024
Smart-AVI

Smart-AVI DVN-16P Handleiding

21 December 2024
Smart-AVI

Smart-AVI SM-DVN-4D Handleiding

21 December 2024
Smart-AVI

Smart-AVI SM-EDPN-4S Handleiding

21 December 2024
Smart-AVI

Smart-AVI SM-EDPN-4D Handleiding

21 December 2024
Smart-AVI

Smart-AVI SM-EDPN-2Q Handleiding

21 December 2024
Smart-AVI

Smart-AVI SM-DVN-4S Handleiding

21 December 2024
Smart-AVI

Smart-AVI SM-UHN-2D Handleiding

21 December 2024
Smart-AVI

Smart-AVI SM-UHN-2S Handleiding

21 December 2024