TP Link Omada ES205GP Handleiding

TP Link Niet gecategoriseerd Omada ES205GP

Lees hieronder de 📖 handleiding in het Nederlandse voor TP Link Omada ES205GP (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Installation Guide
© 2024 TP-Link 7106510830 REV1.0.0
Omada Easy Managed Switch
LED Explanation
LED Explanation
Power On/O: Power on/o
Link/Act;
Uplink1, Uplink2
(For ES210GP)
On (Green): Running at 1000 Mbps
On (Yellow): Running at 10/100 Mbps
Blinking: Transmitting/receiving data
O: No connected device
PoE Status
(For Port 1-4 of ES205GP
/Port 1-8 of ES210GP)
On: Providing PoE power
Blinking: Current-overload/Short-circuit
O: Not providing PoE Power
PoE Max
(For ES205GP ES210GP)/
For ES205GP:
On: 58 W ≤ Total power supply < 65 W
Blinking: Total power supply keeps ≥ 58 W
for more than 2 minuites
O: Total power supply < 58 W
For ES210GP:
On: 116 W ≤ Total power supply < 123 W
Blinking: Total power supply keeps ≥ 116 W
for more than 2 minuites
O: Total power supply < 116 W
For simplicity, we will take ES210GP for example throughout the Guide.
For simplicity, we will take ES205G for example throughout the Guide.
Note:
1. The PoE ports can also connect to non-PoE devices, but only transmit data.
2. The PoE ports shall not be used to charge lithium batteries or devices supplied by lithium batteries.
3. Maximum PoE power is 30 W for each PoE port, and total PoE budget is 65 W (for ES205GP)/
123 W (for ES210GP) respectively.
4. PoE budget calculations are based on laboratory testing. Actual PoE power budget is not
guaranteed and will vary as a result of client limitations and environmental factors.
Method 1: Standalone Mode
The switch supports two conguration methods:
Standalone Mode: Congure and manage the switch singly.
Controller Mode: Congure and manage the network devices centrally. It is recommended in the large-scale network, which consists
of mass devices such as access points, switches, and gateways.
Note: When the switch is changed from Standalone Mode to Controller Mode, congurations of the switch will be lost. For details, refer
to the related documents on the download center of our oîž±cial website: https://www.tp-link.com/support/download/.
In Standalone Mode, use a computer to congure and manage the
switch.
Conguration
3. After a successful login, the main page will appear. You can click
the menus on the top side and left side to congure the
corresponding functions.
2. Enter for both the username and password in the lower admin
case letters to log in. The rst time you log in, change the
password to better protect your network and devices.
For detailed congurations, refer to the User Guide. The guides can
be found on the download center of our oîž±cial website:
https://www.tp-link.com/support/download.
To access the management page of the switch, open a browser
and type the switch’s IP address in the address eld. Then press
the Enter key.
If the switch obtains IP address from the DHCP server
(typically a router), nd the switch’s IP address on the DHCP
server.
If not, use the default IP address to launch the 192.168.0.1
switch’s management page.
Note: Make sure the switch and computer are in the same subnet.
1.
DC P er Adapterow
AC Power Cord
PoE+ Ports (1-8)
IP Camera AP IP Phone
Powered Device (PD)
Router
LAN Port WAN Port
Internet
Ethernet Ports (1–5)
Router
LAN PortWAN Port
Power Adapter
Internet
PC
PC
Choose from the following two types of Management Interface:
Ty e 1: p Via Web Browser
Note:
Before you start, be sure to and your devices power up connect
according to the topology gure.
A DHCP server (typically a router with DHCP function enabled) is
required to assign IP addresses to the EAPs and clients in your local
network.
Omada Controller must have network access to your Omada devices
(the router, switch, and EAPs) in order to nd, adopt, and manage
them.
Ty e 2: Omada Sop ftware Controller
On a PC with Windows OS or Linux OS, download the Omada Software
Controller from
https:// w.tp-link.c /support/download/ww om omada-so ware-controller/ft
Then run the le and follow the wizard to install and launch the Omada
So ware Controller. To manage your devices, Omada Soft ftware
Controller needs to keep running on your computer.
Ty e 1: Omada Hap rdware Controller
Omada Hardware Controller is a good alternative if you h e no spare PC av
to keep running Omada Software Controller in the network. It needs to be
purchased additionally. For more details, refer to the Installation Guide of
Omada Hardware Controller.
1. Open the Omada Controller’s web page.
For Omada Software Controller
Launch the Omada Software Controller on your PC. After the initiation
process, the controller automatically opens its web page. If not, click
Launch a Browser to Manage the Network.
For Omada Hardware Controller
As Omada Hardware Controller gets its IP address from the DHCP
server of the router, we don’t know its IP address explicitly. However,
we can nd it out on the router’s DHCP client list.
On the Omada Controller’s page, follow the wizard to complete the
quick setup.
After quick setup, login page appears. Enter the username and
password you h e created and click . Then you can further av Log in
congure the controller.
(For Remot You can remotely access and manage your e Management)
controller via Omada Cloud Service.
Note: Before you start, make sure that both your controller and your PC
can access the internet.
For Omada Software Controller, refer t ser Guideo its U
For Omada Hardware Controller
Make sure is enabled on your controller. By default, Cloud A esscc
Cloud A esscc is enabled. Make sure that the Cloud LED is îž°ashing
slowly.
Launch a web browser and enter https://omada.tplinkcloud.com
in the address bar. Enter your TP-Link ID and password to log in.
Click + Add Controller Hardware Controller and choose to add your
controller.
Ty e 2: ia Omada Appp V
Download the TP-Link Omada App on your mobile device. It can be
downloaded from App Store or Google Play:
Launch y re the controller at a local site or our Omada App and congu
remote site.
Local Management
Connect your mobile device to the EAP by using the default
S f ted on the SID ( ormat: ) prinTP-Link_2.4GHz/5GHz_XXXXXX
label at the bottom of the product.
Launch Omada App and go to Local Access +, tap the button on
the upper-right corner to add the controller. Then you can
further congure the controller.
Remote Management
Note: Before you start, make sure that both your controller and mobile
device can access the internet.
For Omada Software Controller
Make sure that Cloud Access is enabled on your controller and
your controller has been bound with your TP-Link ID.
Launch Omada App and log in with your TP-Link ID. Then go to
Cloud A esscc . A list of controllers that h e been bound with av
your TP-Link ID will appear. Then you can fur re the ther congu
controller.
For Omada Hardware Controller
Make sure that Cloud Access is enabled on your controller. By
default, Cloud Access is enabled. Make sure that the Cloud LED
is îž°ashing slowly.
Launch Omada App and log in with your TP-Link ID. Then go to
Cloud A esscc . Tap the button on the upper-right to add your +
controller. Then you can fur re the controller.ther congu
Enter the IP address of your controller in address bar to open its web
page.
the router s web page, and both the username and password are admin
by default. Then go to tNetwork > LAN > DHCP Client List o nd the IP
address of your controller according to its MAC address.
c.
2.
3.
4.
a.
b.
You need rst nd the IP address of the router. Open the command
line on your PC and enter . In the result listipcong , nd the Default
Gateway, which is also the IP address of the router.
a.
1.
2.
a.
b.
a.
b.
a.
b.
Environmental and Physical Specications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0 C to 40 F to 104 Ëš ËšC (32 Ëš ËšF)
-40 C to 70 F to 158 Ëš ËšC (-40 Ëš ËšF)
10% RH to 90% RH non-condensing
5% RH to 90% RH non-condensing
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR
code.
To ask questions, find answers, and communicate with TP-Link
users or engineers, please visit https://community.tp-link.com
to join TP-Link Community.
Some models featured in this guide may be unavailable in your country or region. For local sales
information, visit https://www.tp-link.com.
Safety Information
packing of this product. If you have any questions, please don’t hesitate to contact us.
Use only power supplies which are provided by manufacturer and in the origin
Do not use any other chargers than those recommended.
Keep the device away from water, re, humidity or hot environments.
Do not use damaged charger or USB cable to charge the device.
Adapter shall be installed near the equipment and shall be easily accessible.
Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.
EU declaration of conformity
For ES205G:
TP-Link hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and
(EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce/
For ES205GP/ES210GP:
TP-Link hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce/
UK declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical
Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/
Plug the product into the wall outlets with earthing connection through the power supply
cord. (For ES205GP/ES210GP)
The PoE ports shall not be used to charge lithium batteries or devices supplied by
lithium batteries. (For ES205GP/ES210GP)
The socket-outlet shall be installed near the equipment and shall be easily accessible.
(For ES205GP/ES210GP)
The plug on the power supply cord is used as the disconnect device, the socket-outlet
shall be easily accessible. (For ES205GP/ES210GP)
Place the device with its bottom surface downward.

Product specificaties

Merk: TP Link
Categorie: Niet gecategoriseerd
Model: Omada ES205GP

Heb je hulp nodig?

Als je hulp nodig hebt met TP Link Omada ES205GP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd TP Link

TP Link

TP Link EAP653 UR Handleiding

12 November 2024
TP Link

TP Link LS1210P Handleiding

11 November 2024
TP Link

TP Link Archer TBE400UH Handleiding

11 November 2024
TP Link

TP Link Tapo P210 Handleiding

11 November 2024
TP Link

TP Link Deco S1900 Handleiding

30 Juli 2024
TP Link

TP Link Deco BE25 Handleiding

3 Juli 2024
TP Link

TP Link Omada ES205GP Handleiding

3 Juli 2024
TP Link

TP Link Archer TXE50UH Handleiding

10 Juni 2024
TP Link

TP Link EP40M Handleiding

10 Juni 2024
TP Link

TP Link Deco BE75 Handleiding

10 Juni 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Cherry

Cherry SPOS G86-61411 Handleiding

17 November 2024
Cherry

Cherry MX Board 8.0 Handleiding

17 November 2024
Cherry

Cherry Advanced Performance Line G81-8904 Handleiding

17 November 2024
Air Guard

Air Guard AG-1600 Handleiding

17 November 2024
Leviton

Leviton 41089-4WP Handleiding

17 November 2024
Livarno Lux

Livarno Lux IAN 74336 Handleiding

17 November 2024
Livarno Lux

Livarno Lux IAN 277515 Handleiding

17 November 2024
Livarno Lux

Livarno Lux IAN 114812 Handleiding

17 November 2024
Livarno Lux

Livarno Lux IAN 292286 Handleiding

17 November 2024
Livarno Lux

Livarno Lux IAN 291521 Handleiding

17 November 2024