TP Link Archer NX600 Handleiding

TP Link Router Archer NX600

Lees hieronder de 📖 handleiding in het Nederlandse voor TP Link Archer NX600 (2 pagina's) in de categorie Router. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Customize the 5G Router
Note: The router can also be used (or configured) in EWAN Mode(wireless router
mode) for Cable connections. For more advanced configurations, please refer to
the user guide on TP-Link official website at www.tp-link.com.
Note: If the login page does not appear, please refer to Q1 of Need Help? in this
guide.
2 .Launch a web browser and type in orhttp://tplinkmodem.net
http://192.168.1.1. Create a new password for future logins.
3. Follow the step-by-step instructions of the to complete the Quick Setup
initial conguration.
1. Make sure your computer is connected to the router (wired or wireless).
http://tplinkmodem.net
HighMiddleLow
Save
Conrm Password
New Password
Need Help?
Q1. What should I do if I cannot access the web management page?
• If the computer is set to a static IP address, change its settings to obtain an IP address automatically.
• Make sure or is correctly entered in the web browser.http://tplinkmodem.net http://192.168.1.1
• Use another web browser and try again.
• Reboot your router and try again.
• Disable and enable the active network adapter in use.
Q2. What should I do if I cannot access the internet?
• Verify that your SIM card is a 5G/4G or WCDMA card.
• Verify that your SIM card is in your internet service provider’s service area.
• Verify that your SIM card has sufficient credit.
• Check the LAN connection: Open a web browser and enter or http://tplinkmodem.net
http://192.168.1.1 in the address bar. If the login page does not appear, refer to Q1 and then try again.
• Launch a web browser, log in to the web management page, and check the following:
1) Go to Advanced Network Mobile WAN > > to verify the parameters provided by your ISP are correctly
entered. If the parameters are incorrect, click Create Profile and enter the correct parameters, then
select the new profile from the list.Profile Name
2) Go to Advanced Network PIN Management > > to verify if PIN is required. If it is, enter the correct PIN
provided by your ISP, and click .Save
3) Go to Advanced Network Data Settings > > to verify if the Total/Monthly Used exceeds the
Total/Monthly Allowance Correct. If it does, click and set Total/Monthly Used to 0 (zero), or disable
Data Limit.
4) Go to Advanced Network Mobile WAN Mobile Data > > to verify that is enabled. If it is not, enable it to
access the internet.
5) Confirm with your ISP if you are in a roaming service area. If you are, go to Advanced Network > >
Mobile WAN Data Roaming to enable .
6) Confirm the selection of Antenna Type.
If it is determined that an external antenna is connected, select External 5G/LTE Antennas.
If you are sure that no external antenna is connected, select Internal 5G/LTE Antennas.
Q3. How do I restore the router to its factory default settings?
• With the router powered on, press and hold the button on the rear panel of the router until the RESET
Power LED starts flashing, then release the button. Wait while the router resets.
• Log in to the web management page of the router, and go to Advanced System Tools Backup & > >
Restore Factory Restore, click and wait until the reset process is complete.
Q4. What should I do if I forget my web management page password?
• If you are using a TP-Link ID to log in, click Forgot password on the login page and then follow the
instructions to reset it.
• Alternatively, refer to to reset the router, then create a new password to log in. Q3
Q5. What should I do if I forget my wireless network password?
• The default wireless password is printed on the product label of the router.
• Connect a computer directly to the router using an Ethernet cable. Log in to the router's web
management page and go to > Basic Wireless to retrieve or reset your wireless password.
Q6. What should I do if I want to change the LAN/WAN port from default WAN port to LAN port?
• Log in to the web management page of the router, and go to Advanced Network Internet > > to delete
the prole from the Internet Setup list and click Save. Then the default WAN port will change to LAN
port.
For technical support, replacement services, user guides, and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
Safety Information
• Keep the device away from water, re, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Do not use the device where wireless devices are not allowed.
• Adapter shall be installed near the equipment and shall be easily accessible.
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant
provisions of directives 2014/53/EU, 2009/125/EC, 2011 /65/EU and (EU) 2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce/
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant
provisions of the Radio Equipment Regulations 2017.
The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/
UK Declaration of Conformity
Quick Installation Guide
5G CPE Router
©2024 TP-Link 7106511113 REV1.0.0
Connect the Hardware
b. Connect the
power adapter
and turn on the
router.
Power adapter
a. With the gold contacts
facing right, insert the
nano SIM card into the slot
until you hear a click.
Nano
SIM Card
Note: The RESET button is actually a shared RESET/Wi-Fi button (short press for 5 seconds or less is
for Wi-Fi function, long press for 5 seconds or more is for RESET function). A short press will cause
the Wi-Fi in use to turn o.
Verify the Hardware Connection Enjoy the Internet
Wireless
Wired
Connect your computers to the router's LAN ports via Ethernet cables.
Find the SSID (network name) and wireless password printed on the
label at the bottom of the router.
a.
Click the network icon of your computer or go to Wi-Fi settings of your
smart device, and then select the SSID to join the network.
b.
IMEI:XXXXXXXXXXXXXXX
MAC:XX-XX-XX-XX-XX-XX
Wireless Password/PIN:XXXXXXXX
SSID:TP-Link_XXXX
Power: 12V 2A
Note: The LAN/WAN port defaults to WAN port. Please refer to Q6 of Need Help? in this guide
if you want to change it to LAN port.
Congure the router via Tether App
The TP-Link Tether app provides a simple, intuitive way to access and manage
your router.
View information about clients
connected to your router
Block unwelcome users from
connecting to your network
Set up Parental Controls
with access time
Change the basic wireless
network settings
Note: If you don’t have an account, create one rst.
1. Download the TP-Link Tether app.
2. Open the Tether app and log in with your TP-Link ID.
3. Tap the icon in the Tether app and select 4G/5G Router.
Follow the steps to complete the setup and connect to the internet.
or
How to begin?
*Images may dier from actual products.
LED Status Indication
On/O
Flashing
On/O
On
O
On/O
Flashing
Power is on or o.
The system is starting up or rmware is being upgraded.
Do not disconnect or power o your modem router.
Wi-Fi is enabled or disabled.
WPS connection is in progress. This may take up to 2
minutes.
At least one LAN port is connected.
No LAN port is connected or LAN port is not
connected properly.
The signal strength is above 75%.
The signal strength is between 50% and 75%.
The signal strength is below 50%.
No mobile network signal.
(Power)
(Internet) Internet service is available or unavailable.
(Signal
Strength)
(Network
Type)
(Wi-Fi)
Solid white
Solid green
Solid yellow
O
The device is on a 5G/4G+ network (depend on the router).
The device is on a 4G network.
The device is on a 3G network.
The device is not registered on the network.
Solid white
Solid green
Solid yellow
O
(LAN)
Check the following LEDs’ status. If the Internet LED is on, your router is
connected to the internet successfully.
Note: If the Internet LED does not turn on, please refer to Q2 of Need Help? in this guide.
12 3
Note: Due to Tether app updates, your actual user interface and pathway may dier from those
depcited here.


Product specificaties

Merk: TP Link
Categorie: Router
Model: Archer NX600

Heb je hulp nodig?

Als je hulp nodig hebt met TP Link Archer NX600 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Router TP Link

Handleiding Router

Nieuwste handleidingen voor Router