Tornado HI-FAN-12HVWM-WR-1P Handleiding

Tornado Ventilator HI-FAN-12HVWM-WR-1P

Lees hieronder de 📖 handleiding in het Nederlandse voor Tornado HI-FAN-12HVWM-WR-1P (4 pagina's) in de categorie Ventilator. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
12 OUTDOOR RATED WATER RESISTANT"
HIGH-VELOCITY METAL WALL FAN
PLEASE READ AND SAVE THIS INSTRUCTION.
Attention: Pictures in the IM are for reference only.
 
Model: HI-FAN-12HVWM- WR-1P
Intended Use:
This product is intended for use only industrial or commercial .
Use only with electrical wiring that is in good working order and
that meets applicable codes and ordinances. If you have any
questions whether your wiring is adequate, consult a qualified
electrician.
This fan is suitable for outdoor use.
While using your fan, you should follow the IMPORTANT
INSTRUCTIONS listed below. As part of those instructions, we
have used the word "WARNING" to indicate the level of hazard:
WARNING indicates a hazard which, if not avoided, could result
in injury or death.
IMPOR ANT INSTRUCTIONST
As with all electrical appliances, basic safety precautions should
always be followed to reduce the risk of electric shock, fire, or
injury to persons, including the following precautions:
Read all the instructions before using this fan.
Use this fan only as described in this manual. Any other use not
recommended by the manufacturer may cause electrical shock,
fire or injury to persons.
Do not operate the fan with a damaged power cord or after the fan
malfunctions or has been dropped in any manner.
Use of extreme used caution necessary is when any fan is by or
near children, disabled persons or pets and whenever the fan is
left operating unattended.
Do small, not a place the fan on unlevel, uneven or any surface
which might allow fan to tip or fall.
Always unplug fan when not use, in when moving from place to
place, when assembling or disassembling parts, and before
cleaning.
The not by use of attachments, recommended or sold the
manufacturer, may cause hazards.
To reduce the risk of fire or electrical shock, do not use this fan
with any solid state speed control device.
Do not operate the fan with blade guards or any safety device
removed.
Automatically operated device - To reduce the risk of injury,
disconnect from power supply before servicing.
If the power supply cord is damaged, contact your local service
center or a qualified electrician to install an appropriate
replacement cord to prevent any injury or damage.
Do not use an extension cord with this fan.
To reduce the risk of injury to persons, install fan at least 2.1m
(7 feet) above the floor.
Do not run power cord under carpeting. Do not cover cord with
throw rugs, runners or the like. Arrange cord away from traffic
area where it will not be tripped over.
Do not insert or allow any object to enter any openings on the
fan. Doing so may cause electric shock and/or fire hazard.
Avoid contact with moving parts.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure they do not play with
the appliance.
ReAd & SAve TheSe
INSTRUCTIONS
m WARNING:
Risk of electrical shock---This fan is supplied with a grounding
conductor and GFCI type plug. To reduce the risk of electrical
shock, make sure that it is connected only to a PROPERLY
grounded outlet.
Use only on GFCI protected receptacles.
To Reduce The Risk Of Electric Shock, Connect Only To An
Outlet Provided With A Ground Fault Circuit Interrupting Device.
Do not under any circumstances remove the power plug’s ground
prong or ground fault unit. For your personal safety, the fan must
be grounded.
The fan is equipped with a power supply with ground fault circuit
interrupting device. Removal or tampering of power cord will void
warranty.
Never use an extension cord to connect the fan to an outlet. All
installations must be made into a grounded outlet.
m WARNING: Electrical Shock Hazard
Do use with with not damaged cord or Use plug. adequate
electrical system that is up to code.
m CAUTION: To reduce the risk of electric shock, connect
only to an outlet
m WARNING: to Reduce the Risk of Fire or Electric
Shock, do not use this product with any solid‑state speed
control device.
DANGER: Do not submerge motor in water or allow motor to
be exposed to water. Personal injury and/or death could result.
Never handle the fan or motor with wet hands or when standing
on wet or damp surface or in water. Fatal electrical shock could
occur.
3
Installation Instructions
Use the following information as a guideline only. It is the user's
responsibility to be sure the location and the wall surface can
handle the weight of this fan (14.6 lbs).
The wall fan must be mounted on 12 inch (300mm) thick dry and
cement ‑ grouted firm wall or on 4 by 5 inch wood studs / joists.
Use wall bracket as a template for locating the holes to be drilled.
After determining the hole locations, use an appropriate sized
drill bit and, drill holes through mounting surface.
It is recommended that a minimum of grade 5 fasteners be
used. The following are acceptable surfaces for mounting wall
mount assembly.
STEEL SURFACE ‑ When mounting to a steel surface, such
as vertical I‑beam, drill through holes at pre‑marked locations,
using a 9/32" drill bit. Attach wall mount assembly to mounting
surface using 1/4"‑20 hex screw, in combination with 1/4" flat
washers, 1/4" lock washers, and 1/4"‑20 hex nuts.
MASONRY SURFACE ‑ When mounting to a masonry surface
use a 1/4" expansion type bolt or 1/4" masonry lag with
shield designed to handle the weight of this fan. Drill holes
at pre‑marked locations using appropriate sized drill bit as
recommended for the fastener.
Usage:
Fan operation: Always operate the fan in the upright position
following all instructions and recommendations listed in this
manual.
Fan location: Place the fan in the area of the room that will
provide proper fan cooling.
Fan connection: Plug fan directly into 120 volt A.C., 60 Hz
wall outlet. Be sure plug fits tightly in outlet. A loose connection
may cause overheating and damage to the plug or fan.
Note: To prevent overloading a circuit, do not plug the fan into
a circuit that is servicing other electrical needs.
Speed control:
To operate the fan, each pull of the string will
cycle through the following settings:
• OFF
• LOW
• MED
• HIGH
• OFF
Care and Maintenance
Cleaning: CAUTION-Before cleaning the fan be sure to
disconnect power cord from the plug. Clean the grille surface
with a clean damp cloth. Do not use harsh chemical or abrasive
cleaners. DO NOT IMMERSE THE FAN OR ANY WIRES IN
W TER. Replace front grille before fan use. Allow fan to dry A
completely before use. Periodic grille cleaning with a vacuum will
prevent dust build up. The motor is sealed and does not require
any interior maintenance, cleaning or lubrication.
Maintenance: The Internal motor bearings are permanently
lubricated at the factory and do not require any additional
lubrication.
Repair: DO NOT OPER TE THE FAN WITHOUT THE GRILLE IN A
PLACE. DO NOT USE THE FAN IF IT HAS MALFUNCTIONED OR
BECOME DAMAGED IN ANY WAY.
Storage: Keep original carton for storage of the fan. Coil and tie
the power cord to avoid damage during storage.
We are happy to help, contact us : info@ .comtornadofans


Product specificaties

Merk: Tornado
Categorie: Ventilator
Model: HI-FAN-12HVWM-WR-1P

Heb je hulp nodig?

Als je hulp nodig hebt met Tornado HI-FAN-12HVWM-WR-1P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Ventilator Tornado

Handleiding Ventilator

Nieuwste handleidingen voor Ventilator