Toledo TCD 1680K Handleiding

Toledo Accu boormachine TCD 1680K

Lees hieronder de 📖 handleiding in het Nederlandse voor Toledo TCD 1680K (18 pagina's) in de categorie Accu boormachine. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/18

Ferm b.v.

●

P.O. Box 134

●

8280 AC Genemuiden-N L

●

Web: www.ferm.nl 0008/09

Toledo

TCD-960K, TCD-1200K, TCD-1440K, TCD-1440K2,

TCD-1680K, TCD-1800K, TCD-1800K2

Cordless drill

Akku-Bohrmaschine

Accuboormachine

Perceuse à accumulateur

Taladradora con baterias

Furadeira recarregável

Batteriborrmaskine

φορτιζµενο τρυπάνι

Akkuporakone

Batteridrill

Batteriboremaskine

Akkufúrógép

(Hobby célú használatra)

Ni-Cd

USERS MANUAL

GEBRAUCHSANWEISUNG

GEBRUIKSAANWIJZING

MODE D’EMPLOI

MODEO DE EMPLEO

INSTRUÇÕES DE USO

BRUKSANVISNING

O∆ΗΓΙΕΣ ΧΡΗΣΕΩΣ

KÄYTTÖOHJE

BRUGER VEJLEDNING

BRUKSANVISNINGEN

HASZNÁLATI UTASÍTÁS

Art.nr. 818810

Art.nr. 818825

Art.nr. 818845

Art.nr. 818850

Art.nr. 818860

Art.nr. 818870

Art.nr. 818875

Toledo 35

Product: Toledo Cordless drill

Toledo, Genemuiden, The Netherlands

Sound pressure level 75 dB(A)

Vibration (-

aw)< 2,5 m/s2

Cordless drills are supplied with

batteries. If the batteries can no

longer be charged, do not throw

them away but hand them in to the

domestic chemical waste depot.

SERIAL NUMBER

The serial number on the machine consists of the fol-

lowing elements..

Serial nr.

CAREFULLY READ THE INSTRUCTIONS

BEFORE YOU USE THE CORDLESS DRILL!

SPECIAL SAFETY RULES

1. Check that:

- the voltage of the charger corresponds to the

mains voltage. Chargers with an indicated vol-

tage of 220V are also suitable for 230V;

- the cord and the mains plug are in good condi-

tion: not damaged or frayed;

- the secondary voltage of the charger corres-

ponds to the charging voltage of the battery

charger and the supply voltage of the battery;

- the voltage of the battery corresponds to the

supply voltage of the rechargeable drill.

2. Never use a long extension cord with the charger.

3. Immediately switch off the machine when the drill

bit gets stuck during drilling.

4. Always make sure the maximum allowed speed for

accessories is suitable for the speed of the drill.

5. Never tie the chuck key to the drill with a piece of

rope or something simular, but store the key in the

special holder on the top of the machine.

6. Never use the battery charger to charge other

batteries than the battery provided with the drill.

7. Never attempt to open the housing of the battery

pack. Do not incinerate the battery pack as this can

release very dangerous chemicals or cause the bat-

tery pack to explode.

8. Do not use the battery charger or the adapter in

damp or wet conditions.

WHEN USING THE MACHINE:

1. Always switch off the machine before moving it

downward alongside your body.

Never use the reverse switch during drilling!

IMMEDIATELY SWITCH OFF THE MACHI-

NE WHEN:

1. There is a failure in the battery or the battery con-

nections.

2. The switch is defective.

3. Insulation material starts to smoke or smell.

BEFORE USE

1. Use only sharp drill bits that are right for the job:

METAL HSS:

WOOD HSS:

2. Drill or screwdriver bits can easily be mounted in

the drill chuck without a chuck key. Firmly tighten

the drill chuck by hand.

3. Place the battery in the grip handle of the rechar-

geable drill. There is only one way to install the

battery correctly.

ORDER NUMBER/YEAR OF COSTRUCTION

GB English

2Toledo

ART.NR CHARGER

TYPE

V T/MIN

818810 TCD-960K 9,6 0 - 550 TCDL-960 230V~ 50 Hz

818825 TCD-1200K 12 0 - 550 TCDL-1200 230V~ 50 Hz

818845 TCD-1440K 14,4 0 - 550 TCDL-1440 230V~ 50 Hz

818850 TCD-1440K2 14,4 0 - 550 TCDL-1440 230V~ 50 Hz

818860 TCD-1680K 16,8 0 - 900 TCDL-1680 230V~ 50 Hz

818870 TCD-1800K 18 0 - 900 TCDL-1800 230V~ 50 Hz

818875 TCD-1800K2 18 0 - 900 TCDL-1800 230V~ 50 Hz

Ni-Cd Ni-Cd

EXPLANATION OF SAFETY MARKINGS

AVAILABLE SPARE PARTS FOR TCD-1440K/TCD-1440K2

REF.NR. DESCRIPTION TOLEDO NR.

2 KEYLESS CHUCK 406190

4 SWITCH 406189

7 BATTERY TCDB-1440 406181

- CHARGER TCDL-3, 14,4 V 406182

- ADAPTOR TCDL-1440 406183

AVAILABLE SPARE PARTS FOR TCD-1680K

REF.NR. DESCRIPTION TOLEDO NR.

2 KEYLESS CHUCK 406190

4 SWITCH 406189

7 BATTERY 16,8 V, 1200 mA 406174

- CHARGER TCDL-3, 16,8 V 406175

- ADAPTOR TCDL-1680, 3 - 5 hr 406176

AVAILABLE SPARE PARTS FOR TCD-1800K/TCD1800K2

REF.NR. DESCRIPTION TOLEDO NR.

2 KEYLESS CHUCK 406190

4 SWITCH 406189

7 BATTERY 18 V, 1200 mA 406177

- CHARGER TCDL-3, 18 V 406178

- ADAPTOR TCDL-1800, 3 - 5 hr 406179

34 Toledo

CHARGING THE BATTERY

THE BATTERY THAT COMES WITH THE MACHI-

NE IS NOT FULLY CHARGED.

- Only use the battery charger at temperatures

between +10 and +40 °Celsius.

- Only use the battery charger in dry rooms.

CHARGING

- Place the battery charger on a level surface and the

battery pack in the charger.

- Make sure to align the tongue on the battery pack

with the groove inside the charger. Check that the

‘+’ and ‘-’ terminals of the battery pack and the

charger match.

- Push the adapter plug of the mains adapter into the

connector situated in the side of the charger.

- Plug the mains adapter into the (wall) socket.

- The red light goes on indicating that the battery is

being charged.

- The first time be sure to charge the battery for 5

hours before use. After that, charging takes at least

3 hours to reach full capacity.

The red light will not go out when the bat-

tery is fully charged. Never leave the bat-

tery pack in the charger for more than 5

hours, otherwise it will overheat.

DISCHARGING THE BATTERY

Discharging the battery is just as important as

charging it, maybe even more.

- Once the battery has been fully charged, continue

to use the rechargeable drill until you find it is

becoming less powerful and does not reach maxi-

mum speed.

- This means the battery is low. Now it is ready to

be recharged.

- If you attempt to charge the battery when it has

run down to one third of its full capacity, the so-

called ‘memory effect’ may occur. In this case only

the discharged part of the battery is activated,

which may cause the one third part of the battery

that is still charged to crystallize.

- If this happens, the battery can never be used again.

- Do not discharge the battery completely. As soon

as you find that the machine is becoming less

powerful or does not reach maximum speed,

recharge the battery. If you continue to use the

machine, thus completely discharging the battery,

this may result in the so-called ‘reversal of polari-

zation’, i.e. ‘+’ becomes ‘-’ and ‘-’ becomes ‘+’.

Once this has happened, polarity will remain

reversed, causing irreparable damage to the batte-

ry when you attempt to recharge it.

If the cordless drill is not going to be

used for a long period of time, rechar-

ge the battery before storing. From

time to time recharge the battery for

a short period of time, to prevent it

from running down. Store the battery

separately in the plastic case.

HOW TO USE AS A SCREWDRIVER

By mounting screwdriver bits the drill can be used as

an electric screwdriver.

- The screwdriver bits can be mounted directly in

the chuck. Owing to their hexagonal shape the

screwdriver bits will not rotate in the chuck.

- The extension bar allows you to use the screwdri-

ver bits in spots that are otherwise difficult to reach.

- Drive sockets for tightening/loosening bolts, nuts

and screws can be mounted in the special chuck

adapter.

- The torque clutch can be adjusted by means of the

adjusting ring situated at the front of the drill. The

torque clutch not only prevents the screw from

being driven too deep, but also prevents the screw

head, the screwdriver bit or the drill from being

damaged. Torque setting depends on the material

as well as the diameter and the shape of the screw.

- Make sure the adjusting ring of the torque clutch is

in the position when using drills.

- For best results always start slowly and gradually

speed up.

OPERATION

1. On/off switch

Switch the machine on/off by pressing the trigger

switch (4).

2. Switch lock

When the left-/right switch (3) is in the central

position, the trigger switch is locked.

3. Speed control

The speed can be continuously adjusted by pres-

sing the trigger switch (4) hard or less hard.

4. Adjusting the direction of rotation

The direction of rotation can be changed by push-

ing the switch (4).

Toledo 3

AVAILABLE SPARE PARTS FOR TCD-960K

REF.NR. DESCRIPTION TOLEDO NR.

2 KEYLESS CHUCK 406190

4 SWITCH 406189

7 BATTERY TCDB-960 406184

- CHARGER TCDL-3, 9,6 V 406185

- ADAPTOR TCDL-960 406186

AVAILABLE SPARE PARTS FOR TCD-1200K

REF.NR. DESCRIPTION TOLEDO NR.

2 KEYLESS CHUCK 406190

4 SWITCH 406189

7 BATTERY TCDB-1200 406192

- CHARGER TCDL-3, 12 V 406193

- ADAPTOR TCDL-1200 406194

Product specificaties

Merk:	Toledo
Categorie:	Accu boormachine
Model:	TCD 1680K

Heb je hulp nodig?

Als je hulp nodig hebt met Toledo TCD 1680K stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Accu boormachine Toledo

Toledo TCD 1800K Handleiding

2 Augustus 2023

Toledo TCD 1680K Handleiding

2 Augustus 2023

Handleiding Accu boormachine

Nieuwste handleidingen voor Accu boormachine

Einhell BT-CD 10.8 Li Handleiding

10 December 2023

Einhell BT-CD 14.4 2B Handleiding

10 December 2023

Einhell BT-CD 18 1H Handleiding

10 December 2023

Batavia BT-CBCD001 - 7062722 Handleiding

13 Oktober 2023

Powerplus POW30644 Handleiding

25 September 2023

Powerplus POW30646 Handleiding

25 September 2023

Powerplus POW30633 Handleiding

25 September 2023

Python AC 12.0 KV Handleiding

21 September 2023

Metabo BS 18 LTX BL QI Handleiding

27 Augustus 2023

Bruder Mannesmann 17815 Handleiding

8 Juli 2023