Toddy Pro Series 10 Handleiding

Toddy Koffiezetapparaat Pro Series 10

Lees hieronder de 📖 handleiding in het Nederlandse voor Toddy Pro Series 10 (2 pagina's) in de categorie Koffiezetapparaat. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

bridge handle

Water

level

COLD BREW SYSTEM - PRO SERIES v2

Step 1 Install valve assembly so the handle

points away from the system when the valve is

open. Tip: To turn the valve handle, pull out on

the handle. Close the valve completely. Set aside

the cleaning blank.

Step 2 Slide the platform into a new filter, and

fold as indicated above. Holding the bridge handle

insert the platform and filter, guiding the platform

into place until it rests on the support ring.

Step 3 Slowly add filtered water to about 1

inch (2.5 centimeters) above the platform and

filter. This is 3 gallons (or 11 liters) in a Pro

Series 10 and 6 gallons (or 22 liters) in a Pro

Series 20.

Step 4 When adding water, air may get

trapped in the filter. If the filter bubbles up,

gently guide the paddle across the platform

toward the open end to push the air out, taking

care not to tear the filter.

Step 5 Add half of the ground coffee on top of

the platform and filter. Next, add half of the

remaining filtered water (half of what's left after

the initial fill in step 3), pouring evenly to

saturate all the grounds.

Step 6 Carefully stir with the mixing paddle,

avoiding contact with the filter. Repeat step 5 to

add the rest of the coffee and filtered water. Then

place the lid on the brewer. Tip: For best results,

mix coffee grounds by pulling and plunging them

from the edge of the brewer toward the center.

Add half

remaining

water

12 3

465

Step 7 Break the crust and stir again after

30 minutes to release trapped gas and to make

sure all grounds are evenly saturated. This is an

important step to ensure proper extraction.

Step 8 Put the lid back on and allow to brew at

room temperature for 8 to 24 hours, depending

on your preferred flavor profile.

Step 9 Once brewing is complete, attach one

end of the hose to the hose barb and place the

other end into a clean storage vessel. Open the

valve to drain your cold brew coffee extract.

Once draining is complete, refrigerate extract in

airtight containers for up to 2 weeks.

24hwait 30 min

7 98

Brewing Guide

BREWER SIZE

PRO SERIES 10

PRO SERIES 20

GROUND COFFEE

10 LBS (4.5KG)

20 LBS (9KG)

FILTERED WATER

7 GAL (26.5L)

14 GAL (53L)

Metric equivalents are rounded for convenience.

For video tutorials and more information, please scan the QR Code below or visit ToddyCafe.com/Brewing

Turn handle to

the right 90˚

to open valve

Turn handle to left

90˚ to close valve

Tuck front of filter

behind platform

Fold back of filter over

to the front of platform

Please wash all

reusable parts

before first use.

Inner support ring

Version: 11-2021

Serve:

This recipe yields a concentrated extract, which can be diluted to suit your cold brew

application. Visit ToddyCafe.com/Brewing for more recipes and serving ideas.

BREWER SIZE

PRO SERIES 10

PRO SERIES 20

TODDY® CLEANER

2 scoops (80g, cup, 2.8oz)1/3

4 scoops (160g, 2/3 cup, 5.6oz)

Version: 11-2021

12 3

465

Step 1 Using a , invert the brewer over team lift

a waste or compost bin to remove all coffee

grounds and filter platform.

Step 2 Remove the platform from the filter.

Thoroughly rinse the brewer and all parts. Note:

Pro Series filters are compostable.

Step 3 Remove the valve and attach cleaning

blank to the flange using a clean gasket and a

tri-clamp.

Step 4 Add 2 to 3 liters of hot water to the

brewer, then add Toddy® Cleaner per the chart

below. Allow the solution to fully dissolve.

Step 5 Place all components including the

valve assembly, gasket, hose barb, hose, and

tri-clamp into the bottom of the unit below the

platform to ensure they are fully submerged.

Clean with the valve in the open position.

Step 6 Add the paddle and fill with warm

water, nearly to the top of the brewer.

Step 7 Hang the lid on one of the handles.

Wipe lid and paddle handle with a clean towel

dipped in cleaning solution. Let solution soak for

at least 60 minutes.

Step 8 Remove the tri-clamp and cleaning

blank over the sink, drain solution from the

brewer, and allow all parts to air dry. (Do not dry

with a towel.)

Step 9 For extra shine, polish the exterior with

a soft microfiber cloth and warm water.

Cleaning

7 98

60min

Product specificaties

Merk:	Toddy
Categorie:	Koffiezetapparaat
Model:	Pro Series 10

Heb je hulp nodig?

Als je hulp nodig hebt met Toddy Pro Series 10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Koffiezetapparaat Toddy

Toddy Pro Series 20 Handleiding

4 Juli 2023

Toddy Pro Series 10 Handleiding

27 Juni 2023

Toddy Commercial Model Handleiding

13 Juni 2023

Handleiding Koffiezetapparaat

Nieuwste handleidingen voor Koffiezetapparaat

Cecotec Piccolina 400 Handleiding

19 November 2024

Solac Squissita Easy CE4502 Handleiding

18 November 2024

Solac Squissita Easy CE4504 Handleiding

18 November 2024

Solac Squissita Easy Wine CE4506 Handleiding

18 November 2024

Premium PCM599B Handleiding

18 November 2024

Dualit 84516 Handleiding

18 November 2024

Bezzera Aria MN PID Handleiding

18 November 2024

Kenmore KKTK1.7S Handleiding

18 November 2024

Cecotec FreeStyle Latte T Handleiding

18 November 2024

La Cimbali M40 Handleiding

18 November 2024