Thomson ROC330 Handleiding
Thomson
Afstandsbedieningen
ROC330
Lees hieronder de 📖 handleiding in het Nederlandse voor Thomson ROC330 (23 pagina's) in de categorie Afstandsbedieningen. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/23
ROC 330
113
15
14
16
17
18
19
20
23
24
25
26
22
21
2
3
4
5
6
7
8
9
10
11
12
ROC330
A B C
2 x AAA
(LR03)
ROC 330 7/05/99 23:08 Page II
GB
1
Standby key.
Videotext Yes/No: .
Videotext: to stop scrolling pages.
RECORD: keys printed in grey in these Instructions have the same functions as those of your VCR, your
original remote control or your DVD DTH 1000/2000/2500 THOMSON.
To record, press the RECORD key twice.
STOP
REW
Direction keys for vertical travelling through the menus.
ZOOM- ZOOM+, : for horizontal travelling through the menus (with sets supporting this feature).
To access the .menus
- PROG +: allows you to access the channels (received by your TV set, video recorder or satellite receiver)
in either ascending ( ) or descending ( ) order.+ -
When videotext is active, these coloured keys can be used to select headings, depending on the set's make.
For selecting an external source.
Indicator lamp: the red indicator lamp lights up when any key is pressed.
Videotext: Info key.
Videotext: Back to TV programme.
PAUSE
Programming of the remote control.
PLAY
F.FWD
OK: To confirm a selection.
EXIT: To leave the menus.
Switches the TV sound off.
- VOL +: to increase ( ) or decrease ( ) the volume of the TV set.+ -
Number keys 0 to 9: these keys have the same functions as those of your original remote control and
are used to enter the codes of your different sets.
Press this key first, before you type in the 2-digit channel number.
TV, VCR, SAT: use these keys to select the set you want to control.
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
This Universal Remote Control is compatible with most models of infrared-controlled TV sets,
video recorders, LVD players, satellite and cable TV receivers.
This remote control was programmed in the factory, so that you can use it to control most of
the sets of the THOMSON group's make. For this reason, we recommend that prior to
attempting to programme the remote control, you try it out by means of one of the methods
described in this user manual. But first of all, you'll have to load the supplied batteries into
the remote control.
Please keep this guide along with the code list (provided separately), so that you can
subsequently programme your remote control for use with other sets.
1 - Description of the key functions
2 - Testing the not yet programmed remote control
1. Switch on the set you want to control.
2. Position the selector ( ) on the type of set to be controlled:26
TV: television set
VCR: video recorder
SAT: satellite receiver
3. Direct the remote control towards the TV set and try to switch it off by simply
pressing the key B
B
B
B
B( ).1
Should the set not switch off, you'll have to programme the remote control by
means of one of the methods or described hereinafter in chapter 3.A, , B C D
ROC 330 7/05/99 23:08 Page 1
GB
2
3 - Programming the remote control
Method A – Fast programming with 1-digit subcode
Method B – 3-digit codes programming
Before you start programming, you must find the of the set to be controlledsubcode
(television set, video recorder or satellite receiver).
Refer to the list provided with these instructions, page I of the subcodes.
1. Switch on the set you want to control.
2. Position the selector ( ) on the type of set to be controlled:26
TV VCR: television set, : video recorder, SAT: satellite receiver
3. Hold down the key ) until the red indicator lamp ( ) remains lit (theSET UP (17 13
indicator lamp remains on for a couple of seconds, so that you have time enough to
proceed with steps 4 to 6. The indicator lamp flashes to signal that this time is almost
up, and then goes off).
4. While the indicator is lit , type in the subcode (example: for THOMSON).1
5. Direct the remote control towards the set and try to switch it off by pressing the key
B
B
B
B
B( ).1
6. Immediately upon the switching-off of the set to be controlled, press ) to storeOK 20(
the subcode.
7. Should the set not switch off, press key B
B
B
B
B( ) repeatedly, until the set switches off.1
Between two subsequent key depr essions, give the red indicator lamp ( ) enough13
time to extinguish and light up again (about 1 second). Proceeding this way will
enable you to see whether the set responds or not.
8. Immediately upon the switching-off of the set to be controlled, press ) to storeOK 20(
the subcode.
Check of the programming
In principle, your set is ready for receiving the remote control commands.
Check your remote control for proper functioning by performing the test described on
page 4.
Before you start programming, you must find the of the set to be controlledcode
(television set, video recorder or satellite receiver).
Refer to the list provided with these instructions, page II of the codes.
1. Switch on the set you want to control.
2. Position the selector ( ) on the type of set to be controlled:26
TV VCR: television set, : video recorder, SAT: satellite receiver
3. Hold down the key ) until the red indicator lamp ( ) remains lit. TheSET UP (17 13
indicator lamp remains on for a couple of seconds, so that you have time enough to
proceed with step 4. The indicator lamp flashes to signal that this time is almost up,
and then goes off.
4. While the indicator is lit , enter the first digit of the 3-digit code proposed for the set
to be controlled (example: for THOMSON). The red indicator then goes off or016
flashes, if the code is not on the list.
5. Dir ect the remote control towards the set and try to switch it off by pressing the key
B
B
B
B
B( ).1
6. Should the set not switch off, repeat step 3. Then type in the next 3-digit code. Try to
switch off the set by pressing key B
B
B
B
B( ) once. Repeat this procedure by trying out1
each of the 3-digit codes.
Check of the programming
In principle, your set is ready for receiving the remote control commands.
Check your remote control for proper functioning by performing the test described on
page 4.
+
++
ROC 330 7/05/99 23:08 Page 2
Product specificaties
| Merk: | Thomson |
| Categorie: | Afstandsbedieningen |
| Model: | ROC330 |
Heb je hulp nodig?
Als je hulp nodig hebt met Thomson ROC330 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Afstandsbedieningen Thomson
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
Handleiding Afstandsbedieningen
- Afstandsbedieningen Philips
- Afstandsbedieningen LG
- Afstandsbedieningen Alpine
- Afstandsbedieningen Energy Sistem
- Afstandsbedieningen Funai
- Afstandsbedieningen Hama
- Afstandsbedieningen Hannspree
- Afstandsbedieningen Konig
- Afstandsbedieningen Logitech
- Afstandsbedieningen Marantz
- Afstandsbedieningen Meliconi
- Afstandsbedieningen RCA
- Afstandsbedieningen Ruwido
- Afstandsbedieningen Silvercrest
- Afstandsbedieningen Sweex
- Afstandsbedieningen Technics
- Afstandsbedieningen Telefunken
- Afstandsbedieningen Tevion
- Afstandsbedieningen Vivanco
- Afstandsbedieningen One For All
- Afstandsbedieningen Bang And Olufsen
- Afstandsbedieningen Steren
- Afstandsbedieningen T'nB
Nieuwste handleidingen voor Afstandsbedieningen
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022