Tennsco J1842A-SND Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Tennsco J1842A-SND (4 pagina's) in de categorie Kast. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling
For safety, wear a pair of work gloves when assembling or performing a
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by person
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
PK-2310918
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Jumbo Counter-Height Storage Cabinet
Unassembled Models J1842A-N & J2442A-N
Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686
LOAD CAPACITIES PER SHELF LEVEL
48w x 18d
48w x 24d
400 lbs.
400 lbs.
UNIT SIZE WEIGHT CAPACITY
EVENLY DISTRIBUTED
ASSEMBLY OF J1842A-N OR J2442A-N CABINET
Tools Needed: A free 11/ ” nut driver is included with each Tennsco cabinet. 32
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.
2. Place the back panels (Ref. No. 1) on a smooth surface,
making sure that the anges of both panels are facing up.
Overlap the right panel over the left anel. After aligning the
holes, bolt the two panels tightly together with four bolts
and nuts (Ref. Nos. 17 & 18).
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing ange
(A) around the back and bolting tightly together with four
bolts and nuts. Be sure that the lances on all the shelf
adjustment strips (B) point in the same direction.
5. Attach the right side (Ref. No. 3) to the back in the same
manner as you did in step 3, again making sure that
the ange is around the back and that the lances on
the shelf adjustment strips are pointed in the same
direction as those on the back and left side. Push the
side panel up so the studs in the top go through the holes
in the top ange of the side and fasten with three nuts.
6. Attach the sill (Ref. No. 4) to the sides. Place a nut
(Ref. No. 19) loosely on each of the studs and slide
the ends of the sill into the slots on both sides of the
unit. Then, securely tighten the nuts.
4. Attach the top (Ref. No. 8) to the unit by sliding the outer
ange over the back of the unit and the side ange to the
side panel on the unit. The threaded studs should go
through the holes in the top ange
of the side and fasten with
three nuts. Attach the
back to the top
using four
bolts and nuts.
All lances point UP on
the back and side.
B
Flange faces upward.
Flange goes
under back.
A
Slide ends into the slots on
the bottom of the sides.
7. Place the rear ange of the bottom shelf (Ref. No. 5)
into the bottom lances of the back. The ange with two
holes should face the front, hanging over the sill.
Nuts places loosely
on studs of the sill.
Insert the bottom into the bottom lances.
1. Place the locking handle
(Ref. No. 10) on the right
hand door and fasten with
two #8-32 X 1/4 hex-head
bolts and lock washers,
provided with the handle.
2. Turn the handle to the
open position and
place the locking cam
(Ref. No. 11) over the
square shank of the
door handle. The latch
must be facing downward
as shown. Then place the
locking cotter pin (Ref. No.
13) through the hole of the
square shank.
3. With the handle still in the open position, hook the
locking bars (Ref. No. 9) to the locking cam (see
“A” at left). Once in position, slowly rotate the door
handle to the closed position so the lock bars
prot rude from the holes at the top and bottom
of the door (shown at right, below).
4. Slide the nylon lock bar
guide inserts (Ref. No.
12) over the lock bar
ends and through the
door slots (see “B” at
right). Push down rmly
until the guides snap
into place.
5. Attach the “dummy” handle
(Ref. No. 14) using two
#8-32 X 1/4 hex-head bolts
and lock washers.
Handle/Locking System Installation
A
B
B
8. Set the unit upright. Insert the second shelf at the desired
level. Be sure that the ange with the two holes should
face the front.
10. Cabinet must be level for doors to
open and close properly. Insert a
athead screwdriver into the two
leveling holes and turn the screws
until the cabinet is level. The cabinet
is now ready for use.
NOTE: In order to place the shelf, you must first tilt
the shelf slightly to the left or right before inserting
into the unit.
9. Attach the left door (Ref. No. 6) to the unit by placing the
door on the hinges, aligning the hinge holes, placing the
hinge pins (Ref. No. 15) into the slots and tapping them in
until secure. Attach the right door (Ref. No. 7) to the unit
in the same manner as the left door.
Product specificaties
| Merk: | Tennsco |
| Categorie: | Kast |
| Model: | J1842A-SND |
Heb je hulp nodig?
Als je hulp nodig hebt met Tennsco J1842A-SND stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kast Tennsco
20 Juni 2023
16 Juni 2023
13 Juni 2023
13 Juni 2023
6 Juni 2023
6 Juni 2023
4 Juni 2023
30 Mei 2023
26 Mei 2023
23 Mei 2023
Handleiding Kast
- Kast HP
- Kast IKEA
- Kast Siemens
- Kast Apc
- Kast Bopita
- Kast Bruynzeel
- Kast Butler
- Kast Flexa
- Kast Foppapedretti
- Kast Gude
- Kast Habitat
- Kast Handson
- Kast Livarno
- Kast Marantz
- Kast Milwaukee
- Kast Miomare
- Kast Pali
- Kast Powerfix
- Kast Sencys
- Kast Tiger
- Kast United Office
- Kast Wehkamp
- Kast Woood
- Kast Jysk
- Kast Leen Bakker
- Kast Parisot
- Kast Talgø
- Kast Tvilum
- Kast Bush
- Kast Paidi
- Kast Silver Cross
- Kast Vipack
- Kast BoConcept
- Kast KidKraft
- Kast MADE
- Kast Nolte
- Kast Rauch
- Kast Royal Catering
- Kast BDI
- Kast Zuiver
- Kast Profijt Meubel
- Kast Ordex
- Kast Woonexpress
- Kast Hygena
- Kast Kwantum
- Kast Sanus
- Kast Kirkton House
- Kast Empire
- Kast Dutchbone
- Kast Hooker
- Kast Calligaris .com
- Kast Gami
- Kast Kanto
- Kast Livarno Lux
- Kast Toomax
- Kast Gladiator
- Kast Arthur Berndt
- Kast Bbf
Nieuwste handleidingen voor Kast
16 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
7 December 2024
7 December 2024
7 December 2024