Tennsco CVD1472 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Tennsco CVD1472 (4 pagina's) in de categorie Kast. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling
For safety, wear a pair of work gloves when assembling or performing
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from th
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by person
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
PK-1760918
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Combination Storage Cabinet
Unassembled Model 1472 or CVD1472
Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686
LOAD CAPACITIES PER SHELF LEVEL
36w x 18d
18w x 18d
200 lbs.
75 lbs.
UNIT SIZE WEIGHT CAPACITY
EVENLY DISTRIBUTED
ASSEMBLY OF 1472 or CVD1472 CABINET
Tools Needed: A free 11/ ” nut driver is included with each Tennsco cabinet. 32
Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.
2. Place the cabinet back (Ref. No. 1) on a
protected surface to prevent
scratching the paint.
The ange on the
bottom of the back
should be facing upward.
1. The reference numbers used throughout this sheet refer
to the illustration on the back cover. This is to help you
to identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
ange (A) around the back and bolting together with
seven bolts and nuts (Ref. Nos. 21 & 22). Be sure that the
lances on all shelf adjustment strips (B) are pointing in the
same direction.
5. Insert the shelf (Ref. No. 4) into
the second lance of the side
and back panels.
6. Attach the top (Ref. No. 5) to the unit by sliding the outer ange
over the back of the unit and the side ange of the side panel on
the unit. The threaded studs should go through
the holes in the top lange of the side and
fasten with three nuts. Attach the back
to the top using four bolts
and nuts.
4. Attach the right side (Ref. No. 3) to the back in the same
manner as you did in step 3, again, making sure that
the ange is around the back and that the lances on the
shelf adjustment strips are pointed in the same direction
as those on the back and left side. 8. Place the rear ange of the bottom (Ref. No. 7) into the
bottom lances of the back. The ange with two holes should
face the front, hanging over the sill. Insert the bolts through
the bottom and still with the head
facing the front of the unit.
Secure with two nuts.
Tighten all bolts.
All lances point UP on
both backs and side.
Flange goes
under back.
Flange faces upward.
Flanges
face upward
Slide ends in to the slots
on the bottom of the sides.
Nuts placed loosely
on studs of the sill.
Insert bottom into
bottom lances.
B
A
NOTE: When bolting the unit together, leave
the bolts slightly loose until Step 8, unless
otherwise specified.
NOTE: All illustrations show a solid door. Assembly
for C-Thru doors (CVD1472) is identical.
Two holes must
be in front
Inset A
Use 2nd
lance
7. Next, attach the sill (Ref. No. 6) to the sides, as shown above.
Place nuts loosely on each of the studs and slide the ends of the
sill into the slots on both sides of the unit. Then, securely tighten
the nuts.
11. Insert the four partition shelves
(Ref. No. 11) at the desired levels.
The shelves should be inserted
using the same method used to
place the top shelf.
10. Attach the left coat rod bracket
(Ref. No. 19) beneath the left side
of the cabinet shelf by inserting one
bolt through the hole in the
left edge of the shelf. Secure with a
nut. Attach the right bracket in
the same way. Then slide the
coat rod (Ref. No. 18) through the
holes in the brackets.
Leveler
Access Holes
9. Using two people, set the unit
upright and insert the partition
(Ref. No. 10) into the cabinet,
alining the four holes in the
partition with the holes in the
cabinet bottom and the
cabinet shelf. Attach
with four bolts and
nuts, making sure that
the bolts are inserted from
the top downward to prevent
stored items from being snagged.
NOTE: In order to place the
shelves, you must first tilt
the shelf slightly to the left
or right before inserting
into the unit.
13. The cabinet must be level
in order for the doors to
close properly. Levelers
may be adjusted by
placing the nut driver
through the hole in each
end of the sill and adjusting
the leveling screw.
12. Attach the left door (Ref.
No. 8) and the right door
(Ref. No. 9) to the unit
by placing the door on
the hinges, aligning the
hinge holes, and dropping
the hinge pins (Ref. No.
17) into the slots. Then,
tap the top of each hinge
pin until fully seated.
1. Place the locking handle
(Ref. No. 13) on the right
hand door and fasten with
two #8-32 X 1/ 4hex-head
bolts and lock washers,
provided with the handle.
2. Turn the handle to the
open position and
place the locking cam
(Ref. No. 14) over the
square shank of the
door handle. The latch
must be facing downward
as shown. Then place the
locking cotter pin (Ref. No.
15) through the hole of the
square shank.
3. With the handle still in the open position, hook the
locking bars (Ref. No. 12) to the locking cam (see
“A” at left). Once in position, slowly rotate the door
handle to the closed position so the lock bars
prot rude from the holes at the top and bottom
of the door (shown at right, below).
4. Slide the nylon lock bar
guide inserts (Ref. No.
16) over the lock bar
ends and through the
door slots (see “B” at
right). Push down rmly
until the guides snap
into place.
Handle/Locking System Installation
A
B
B
Product specificaties
| Merk: | Tennsco |
| Categorie: | Kast |
| Model: | CVD1472 |
Heb je hulp nodig?
Als je hulp nodig hebt met Tennsco CVD1472 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kast Tennsco
20 Juni 2023
16 Juni 2023
13 Juni 2023
13 Juni 2023
6 Juni 2023
6 Juni 2023
4 Juni 2023
30 Mei 2023
26 Mei 2023
23 Mei 2023
Handleiding Kast
- Kast HP
- Kast IKEA
- Kast Siemens
- Kast Apc
- Kast Bopita
- Kast Bruynzeel
- Kast Butler
- Kast Flexa
- Kast Foppapedretti
- Kast Gude
- Kast Habitat
- Kast Handson
- Kast Livarno
- Kast Marantz
- Kast Milwaukee
- Kast Miomare
- Kast Pali
- Kast Powerfix
- Kast Sencys
- Kast Tiger
- Kast United Office
- Kast Wehkamp
- Kast Woood
- Kast Jysk
- Kast Leen Bakker
- Kast Parisot
- Kast Talgø
- Kast Tvilum
- Kast Bush
- Kast Paidi
- Kast Silver Cross
- Kast Vipack
- Kast BoConcept
- Kast KidKraft
- Kast MADE
- Kast Nolte
- Kast Rauch
- Kast Royal Catering
- Kast BDI
- Kast Zuiver
- Kast Profijt Meubel
- Kast Ordex
- Kast Woonexpress
- Kast Hygena
- Kast Kwantum
- Kast Sanus
- Kast Kirkton House
- Kast Empire
- Kast Dutchbone
- Kast Hooker
- Kast Calligaris .com
- Kast Gami
- Kast Kanto
- Kast Livarno Lux
- Kast Toomax
- Kast Gladiator
- Kast Arthur Berndt
- Kast Bbf
Nieuwste handleidingen voor Kast
16 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
7 December 2024
7 December 2024
7 December 2024