Tennsco 2436 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Tennsco 2436 (4 pagina's) in de categorie Kast. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
GENERAL SAFETY INFORMA
GENERAL SAFETY INFORMA
GENERAL SAFETY INFORMA
GENERAL SAFETY INFORMATION
TION
TION
TIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling
For safety, wear a pair of work gloves when assembling or performing a
LIMITED WARRANTY
LIMITED WARRANTY
LIMITED WARRANTY
LIMITED WARRANTYLIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by person
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
PK-1451119
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RET
RET
RET
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
AIN INSTRUCTIONS FOR FUTURE REFERENCE
AIN INSTRUCTIONS FOR FUTURE REFERENCE
AIN INSTRUCTIONS FOR FUTURE REFERENCE RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
36” High Standard Storage Cabinet
Unassembled Models 1436 & 2436
Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686
LOAD CAP
LOAD CAP
LOAD CAP
LOAD CAPACITIES PER SHELF LEVEL
ACITIES PER SHELF LEVEL
ACITIES PER SHELF LEVEL
ACITIES PER SHELF LEVELLOAD CAPACITIES PER SHELF LEVEL
36w x 18d 200 lbs.
UNIT SIZE
UNIT SIZE
UNIT SIZE
UNIT SIZEUNIT SIZE WEIGHT CAP
WEIGHT CAP
WEIGHT CAP
WEIGHT CAPACITY
ACITY
ACITY
ACITYWEIGHT CAPACITY
EVENL
EVENL
EVENL
EVENL
Y DISTRIBUTED
Y DISTRIBUTED
Y DISTRIBUTED
Y DISTRIBUTEDEVENLY DISTRIBUTED
36w x 24d 200 lbs.
ASSEMBLY OF 1436 OR 2436 CABINET
Tools Needed: A free 11/ ” nut driver is included with each Tennsco cabinet. 32
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.
2. Place the cabinet back (Ref. No. 1) on a protected surface
to prevent scratching the paint. The ange on the bottom of
the back should be facing upward.
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
ange (A) around the back and bolting the back and side
together with four bolts and nuts (Ref. Nos. 17 & 18). Be
sure that the lances on all shelf adjustment strips (B) point in
the same direction.
5. Attach the right side (Ref. No. 3) to the back in the same
manner as you did in step 3, again making sure that the
ange is around the back and that the lances on the
shelf adjustment strips are pointed in the same direction
as those on the back and left side. Push the side panel up
so the studs in the top
go through the
holes in the
top ange of
side and
fasten with
three nuts.
6. Attach the sill (Ref. No. 6) to the sides. Place nuts
loosely on each of the studs and slide the ends of the
sill into the slots on both sides of the unit. Then,
securely tighten the nuts.
4. Attach the top (Ref. No. 5) to the unit by sliding the outer
ange over the back of the unit and the side ange to the
side panel on the unit. The threaded studs should go
through the holes in the
top ange of the
side and fasten
with three nuts.
Attach the back
to the top using
four bolts
and nuts.
All lances point UP on
the back and side.
B
B
B
B
B
Flange faces upward.
Flange goes
under back.
A
A
A
AA
7. Place the rear ange of the bottom (Ref. No. 9) into the
bottom lances of the back. The ange with two holes should
face the front, hanging over the sill. Insert bolts through the
bottom and sill with the head facing the front of the unit.
Secure with
two nuts.
Insert shelf into the
bottom lances.
1. Place the locking handle
(Ref. No. 11) on the right
hand door and fasten with
two #8-32 X 1/4 hex-head
bolts and lock washers,
provided with the handle.
2. Turn the handle to the
open position and
place the locking cam
(Ref. No. 12) over the
square shank of the
door handle. The latch
must be facing downward
as shown. Then place the
locking cotter pin (Ref. No.
14) through the hole of the
square shank.
3. With the handle still in the open position, hook the
locking bars (Ref. No. 10) to the locking cam (see
“A” at left). Once in position, slowly rotate the door
handle to the closed position so the lock bars
prot rude from the holes at the top and bottom
of the door (shown at right, below).
4. Slide the nylon lock bar
guide inserts (Ref. No.
13) over the lock bar
ends and through the
door slots (see “B” at
right). Push down rmly
until the guides snap
into place.
Handle/Locking System Installation
A
B
B
9. Insert the shelves
(Ref. No. 4) at the
desired levels.
10. Attach the left door (Ref. No. 7) to the unit by placing the
door on the hinges, aligning the hinge holes, dropping the
pins into the slots, then placing the at end of a
screwdriver on the hinge pins
(Ref. No. 15) and
tapping them in with
a hammer.
8. Set the unit upright and tighten all the nuts and bolts
around the entire unit.
NOTE: In order to
place the shelves, you
must first tilt the shelf
slightly to the left or right
before inserting it into the unit.
11. Attach the right door (Ref. No. 8) to the unit in the same
way you attached the left door.
Leveler
Access Holes
12. The cabinet must be level in order for the doors to close
properly. Levelers may be adjusted by placing the nut driver
through the hole in each end of the sill and adjusting the
leveling screw.
Product specificaties
| Merk: | Tennsco |
| Categorie: | Kast |
| Model: | 2436 |
Heb je hulp nodig?
Als je hulp nodig hebt met Tennsco 2436 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kast Tennsco
20 Juni 2023
16 Juni 2023
13 Juni 2023
13 Juni 2023
6 Juni 2023
6 Juni 2023
4 Juni 2023
30 Mei 2023
26 Mei 2023
23 Mei 2023
Handleiding Kast
- Kast HP
- Kast IKEA
- Kast Siemens
- Kast Apc
- Kast Bopita
- Kast Bruynzeel
- Kast Butler
- Kast Flexa
- Kast Foppapedretti
- Kast Gude
- Kast Habitat
- Kast Handson
- Kast Livarno
- Kast Marantz
- Kast Milwaukee
- Kast Miomare
- Kast Pali
- Kast Powerfix
- Kast Sencys
- Kast Tiger
- Kast United Office
- Kast Wehkamp
- Kast Woood
- Kast Jysk
- Kast Leen Bakker
- Kast Parisot
- Kast Talgø
- Kast Tvilum
- Kast Bush
- Kast Paidi
- Kast Silver Cross
- Kast Vipack
- Kast BoConcept
- Kast KidKraft
- Kast MADE
- Kast Nolte
- Kast Rauch
- Kast Royal Catering
- Kast BDI
- Kast Zuiver
- Kast Profijt Meubel
- Kast Ordex
- Kast Woonexpress
- Kast Hygena
- Kast Kwantum
- Kast Sanus
- Kast Kirkton House
- Kast Empire
- Kast Dutchbone
- Kast Hooker
- Kast Calligaris .com
- Kast Gami
- Kast Kanto
- Kast Livarno Lux
- Kast Toomax
- Kast Gladiator
- Kast Arthur Berndt
- Kast Bbf
Nieuwste handleidingen voor Kast
16 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
7 December 2024
7 December 2024
7 December 2024