Tennsco 1870 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Tennsco 1870 (4 pagina's) in de categorie Kast. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling
For safety, wear a pair of work gloves when assembling or performing a
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by person
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
PK-1810918
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Deluxe Storage Cabinet
Unassembled Models 1870 & 2470
Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686
LOAD CAPACITIES PER SHELF LEVEL
36w x 18d
36w x 24d
200 lbs.
200 lbs.
UNIT SIZE WEIGHT CAPACITY
EVENLY DISTRIBUTED
ASSEMBLY OF 1870 OR 2470 CABINET
Tools Needed: A free 11/ ” nut driver is included with each Tennsco cabinet. 32
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.
2. Place the cabinet back (Ref. No. 1) on a protected surface
to prevent scratching the paint. The ange on the bottom of
the back should be facing upward.
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
ange (A) around the back and bolting it together
with seven bolts and nuts Ref. Nos. 15 & 16). Be sure that
the lances on all shelf adjustment strips (B) point in the
same direction.
5. Insert one shelf (Ref. No. 4) into the approximate center
of the unit, inserting the shelf edges into the lances on
all four shelf adjustment strips. Be sure that the channeled
edge of the shelf is toward the cabinet front.
6. Place the top (Ref. No. 5) onto the unit. Be sure that the
anges tuck inside the cabinet sides and back. Secure
with eleven nuts and bolts. The front part of the top will
bolt into place in step 8.
4. Attach the right side (Ref. No. 3) to the back in the same
manner as in step 3, again making sure that the ange
is around the back and that the lances on the shelf
adjustment strips are pointed in the same direction as those
on the back and left side.
7. With both doors in the closed position, lift the door
and frame assembly (Ref. No. 6) and place it over the
cabinet body. Be aware that the door latches have not
yet been attached,
All lances point UP on
the back and side.
Flanges
face upward
B
so the doors could
potentially swing
open if the door
frame is held in
an upsidedown
position. The
door frame should
cover the outside
edges of the
entire storage
cabinet front.
NOTE: When bolting the unit together, leave
the bolts slightly loose until Step 10, unless
otherwise specified.
Flange faces upward.
Flange goes
under back.
A
1. Place the locking handle
(Ref. No. 9) on the right
hand door and fasten with
two #8-32 X 1/4 hex-head
bolts and lock washers,
provided with the handle.
2. Turn the handle to the
open position and
place the locking cam
(Ref. No. 10) over the
square shank of the
door handle. The latch
must be facing downward
as shown. Then place the
locking cotter pin (Ref. No.
12) through the hole of the
square shank.
3. With the handle still in the open position, hook the
locking bars (Ref. No. 8) to the locking cam (see
“A” at left). Once in position, slowly rotate the door
handle to the closed position so the lock bars
prot rude from the holes at the top and bottom
of the door (shown at right, below).
4. Slide the nylon lock bar
guide inserts (Ref. No.
11) over the lock bar
ends and through the
door slots (see “B” at
right). Push down rmly
until the guides snap
into place.
5. Attach the “dummy” handle
(Ref. No. 13) using two
#8-32 X 1/4 hex-head bolts
and lock washers.
Handle/Locking System Installation
A
B
B
8. With the door and frame assembly in place, attach it
securely to the unit by opening each
door, one at a time, and securing
the frame assembly using
two bolts and twenty
nuts. This will
require attaching
nuts to the
nine pre-welded
studs along
each side, plus
two bolts and
nuts along the top.
Using two people, set the unit upright and tighten all nuts
around the entire unit. Insert the remaining shelves at your
desired levels. The shelf you inserted earlier may also be moved
to a different level if desired.
10.
Two holes
must be in front.
Insert shelf
into bottom lances.
Levelers
Access Holes
11. The cabinet must be
level in order for the
doors to close properly.
Levelers may be adjusted
by placing the nut driver
through the hole in each
end of the sill and adjusting
the leveling screw.
NOTE: In order to place
the shelves, you must
first tilt the shelf slightly
to the left or right before
inserting it into the unit.
9. Place the the bottom (Ref. No. 7) in the lowest notch of the
shelf adjusting strips on the back. Make sure the ange with
two holes faces the front, and that it is over the ange of the
frame sill. If necessary, you may
push out on the side
walls to
enable
the bottom
to more
easily slide
into position. Attach
the shelf securely by bolting
the bottom to the frame sill
with two bolts and nuts.
Product specificaties
| Merk: | Tennsco |
| Categorie: | Kast |
| Model: | 1870 |
Heb je hulp nodig?
Als je hulp nodig hebt met Tennsco 1870 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kast Tennsco
20 Juni 2023
16 Juni 2023
13 Juni 2023
13 Juni 2023
6 Juni 2023
6 Juni 2023
4 Juni 2023
30 Mei 2023
26 Mei 2023
23 Mei 2023
Handleiding Kast
- Kast HP
- Kast IKEA
- Kast Siemens
- Kast Apc
- Kast Bopita
- Kast Bruynzeel
- Kast Butler
- Kast Flexa
- Kast Foppapedretti
- Kast Gude
- Kast Habitat
- Kast Handson
- Kast Livarno
- Kast Marantz
- Kast Milwaukee
- Kast Miomare
- Kast Pali
- Kast Powerfix
- Kast Sencys
- Kast Tiger
- Kast United Office
- Kast Wehkamp
- Kast Woood
- Kast Jysk
- Kast Leen Bakker
- Kast Parisot
- Kast Talgø
- Kast Tvilum
- Kast Bush
- Kast Paidi
- Kast Silver Cross
- Kast Vipack
- Kast BoConcept
- Kast KidKraft
- Kast MADE
- Kast Nolte
- Kast Rauch
- Kast Royal Catering
- Kast BDI
- Kast Zuiver
- Kast Profijt Meubel
- Kast Ordex
- Kast Woonexpress
- Kast Hygena
- Kast Kwantum
- Kast Sanus
- Kast Kirkton House
- Kast Empire
- Kast Dutchbone
- Kast Hooker
- Kast Calligaris .com
- Kast Gami
- Kast Kanto
- Kast Livarno Lux
- Kast Toomax
- Kast Gladiator
- Kast Arthur Berndt
- Kast Bbf
Nieuwste handleidingen voor Kast
16 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
15 December 2024
7 December 2024
7 December 2024
7 December 2024