Tecnoinox SE 80 Handleiding

Tecnoinox Niet gecategoriseerd SE 80

Lees hieronder de đź“– handleiding in het Nederlandse voor Tecnoinox SE 80 (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 198 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/9
502040-60-80 en fr de ma 2012 1/9
sInstruction manual for installation and use
sInstallations- und Gebrauchsanweisungen
sNotice d’installation et d’emploi
Mod.
SE 40 / SE 60 / SE 80
ELECTRIC SALAMANDER
SALAMANDRES ELECTRIQUES
ELEKTRISCHE SALAMANDER
GB
DE
FR
ART. *502.040 - *502.060 - *502.080
502040-60-80 en fr de ma 2012 2/9
SE 40 SE 60 SE 80 SCP
Dimensioni External AuĂźenmaĂźe Dimensions Dimensiones mm mm mm mm
esterne dimensions extérieures externas 400x450 600x450 800x450 550x450
x500h 500h x500h x500h
Dimensioni Plate Abmessungen Dimensions Dimensiones mm mm mm mm
piano cottura dimensions Kochplatte plaque de cuisson plano de cocciĂłn 400x350 600x350 800x350 550x350
Potenza Installed Nennleistung Puissance Potencia kW kW KW KW
6642adalatsnieéllatsnirewopatallatsni
~ 032 VnĂłisneTnoisneTgnunnapSegatloVenoisneT
V 230 ~ V 400~2N V 400~3N V 400~3N
Schema fĂĽr Betonwandbohrungen zur Befestigung der Wandhalterungen
Diagram for drilling cement walls for the fastening of brackets
Schéma de perçage de la paroi en béton pour fixer les étriers
502040-60-80 en fr de ma 2012 3/9
Part 1 Installation
General instructions
The appliance referred to in this manual has been
manufactured in conformity to the following Directives:
73/23/EEC, 93/68/EEC “Low Voltage”; 89/336/
EEC, 92/31/EEC, 93/68/EEC “Electromagnetic
Compatibility".
The appliance shall be installed by a qualified tech-
nician according to the regulations and directives in
force in the country where it is installed, as well as the
instructions in this manual. The appliance shall be
used exclusively by trained personnel and only for
the purpose for which it has been designed. The
appliance should be checked once a year by a
qualified technician.
Remove the packaging form the appliance as well
as the protective plastic sheet, and, if necessary, re-
move traces of glue with a suitable solvent. Remove
the screw, to be found on the rear of the appliance,
which locks the movable shelf in place. To dispose of
the packaging, follow local directives.
The technical specifications are to be found on the
specification plate attached to the appliance’s rear
panel.
When installing the appliance, all the regulations
in force shall be observed, such as:
sall applicable national laws in effect;
sall regional or local regulations, such as building codes;
sdirectives and regulations of the local electrical
energy supplier;
saccident prevention regulations in effect;
sfire prevention regulations;
sapplicable I.E.C. regulations.
The appliance should be installed under an
extractor fan for the removal of cooking fumes.
If the appliance is installed near walls,
panels or kitchen furniture, etc., these must
be made of fire-proof material; if they are
not, they must be protected with fire-proof
material which insulates from heat.
ELECTRIC SALAMANDER SE 40 - SE 60 - SE 80 - SCP
Connection to the mains
Before connecting the appliance to the mains, com-
pare the electrical set-up data on the data plate to the
characteristics of the local electrical energy supply.
The appliance is equipped with a connecting cable
to which the installer must connect a circuit breaker
which cuts off the flow of electricity in all poles; the
distance between the open contacts must be at least
3 mm. The circuit breaker must be easy to reach.
The cable must not be placed near heat sources.
The area around the cable must not have a tempera-
ture above 50° C. If the cable must ever be replaced,
consult the wiring diagram attached. The supply
cable’s characteristics must be of a HO7 RN-F type,
or higher, and its minimum cross-section must be in
accordance with the following table:
MODEL CABLE CROSS-SECTION
SE 40 V 230~ 3x1,5 mm2
SE 60 V230~ 3x2,5 mm2
SE 60 V400~2N 5x1,5 mm2
SE 80 V400~ 3N 5x1,5 mm2
SCP V400~ 3N 5x1,5 mm2
Remove panel “ ”, to be found on the rear side,C
in order to make the “M” terminal board accessible.
Disconnect the conductors of the electric supply cable
from the terminal board, loosen the cable clamp, and
replace the cable following the procedure inversely.
It is absolutely necessary to earth the appliance.
For this purpose, there is a screw marked with the
symbol near the terminal board to which the
earthing conductor must be connected.
The appliance must also be connected to a
unipotential earthing circuit. The connection must be
made by means of the screw marked to be found
on the rear panel of the appliance.
The Manufacturer declines any responsi-
bility for damage caused by improper or in-
correct installation or maintenance of the ap-
pliance, or failure to observe safety regula-
tions!
GB

Product specificaties

Merk: Tecnoinox
Categorie: Niet gecategoriseerd
Model: SE 80

Heb je hulp nodig?

Als je hulp nodig hebt met Tecnoinox SE 80 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Tecnoinox

Tecnoinox

Tecnoinox SE 60 Handleiding

5 Januari 2024
Tecnoinox

Tecnoinox SE 80 Handleiding

4 Januari 2024
Tecnoinox

Tecnoinox SE 40 Handleiding

4 Januari 2024
Tecnoinox

Tecnoinox 502005 Handleiding

3 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Lucide

Lucide Rune 79178/08/30 Handleiding

22 November 2024
Lucide

Lucide Twinka 79176/12/61 Handleiding

22 November 2024
Lucide

Lucide Gently 79172/12/12 Handleiding

22 November 2024
Lucide

Lucide Foskal 79177/06/14 Handleiding

22 November 2024
Lucide

Lucide Rune 79178/08/72 Handleiding

22 November 2024
Lucide

Lucide Troy 79180/12/30 Handleiding

22 November 2024
Lucide

Lucide Dexty led 79195/18/61 Handleiding

22 November 2024
Lucide

Lucide Tonga 79459/25/30 Handleiding

22 November 2024
Lucide

Lucide Slits 27898/10/29 Handleiding

22 November 2024
Lucide

Lucide Ottelien 30771/16/30 Handleiding

22 November 2024