TC Electronic M5000 Handleiding

TC Electronic Niet gecategoriseerd M5000

Lees hieronder de 📖 handleiding in het Nederlandse voor TC Electronic M5000 (14 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/14
CONFIG. M5000
M5CONFIG
Rev 1.3 Page 1
CONFIGURATION
This section contains text modules concerning configuring either software or hardware
applications. When software is released or a new module card is purchased, refer to this
section in order to install it properly. The section contains the following text modules:
M5000 APPLICATIONS
SOFTWARE INSTALLATION
HARDWARE INSTALLATION
OPTION INSTALLATION
HIGH MEMORY OPTION
SIMM PACK INSTALLATION
CONFIG. M5000
M5CONFIG
Rev 1.2 Page 2
MULTIPLE ATAC/M5000/M5000X SETUP
The ATAC-remote system is capable of controlling multiple M5000/X main frames. The link
that enables the data communication is the TC DUAL RS485 INTERFACE for M5000/X,
also referred to as the MULTAC, and the proprietary TC Network Protocol. The RS485
INTERFACE and a connection example is illustrated below:
With one RS485 INTERFACE (MULTAC) you are able to connect one or two M5000/X
frames. The M5000/X´s are to be connected to the M5000/X #1 and #2 plugs (Fig.1).
The RS485 plugs each connect to either one ATAC or is used to loop on to the next
MULTAC box (Fig.2). Additionally, you are able to connect two ATACs using both RS485
sockets.
When connecting two ATACs, in a multiple M5000/X/ATAC setup, you gain the advantage
that two users can communicate simultaneously. Please note that two users cannot access the
same mainframe at once.
The MULTAC also has DC plug connections for the ATAC power supplies.
Cables:
You may substitute the cable, connecting the ATAC to the MULTAC, with a “MIDI Plus”
cables (5 pins with shield).
A 7 pin cable with shield must be used when connecting the M5000/X with the MULTAC.
Note: To ensure a safe data transferal, please follow the cable length requirements stated
below:
1. When only ONE M5000X is connected use max. 10m/33ft of remote cable.
2. In a MULTIPLE M5000/X/ATAC setup, lengths of the cables connecting the ATAC to the
MULTAC can be extended to 100m/328ft. Maximum lenghts may not exceed 100
meters/328 ft.
CONFIG. M5000
M5CONFIG
Rev 1.3 Page 3
SOFTWARE INSTALLATION M5000
Here is the procedure for updating the application software in the M5000. You need to get to
the special M5000 Setup Utility menu to accomplish this.
1. Turn the power off the M5000.
2. Press the BYPASS button (22) while switching power on again. Hold it for a
few seconds. The M5000 Setup Utility Menu will appear.
3. With the PROGRAM DIAL (17) you choose the appropriate option:
LOAD DISK/CARD When DO is pressed the directory of the inserted
floppy disk or memory card will appear. Scroll
through the files with PROGRAM DIAL. Select the
file by pressing DO and confirm the choice by
pressing DO again. Software from floppy disk or
memory card will be loaded. The UNDO button works
as a cancel button and returns you to the Setup Menu.
SAVE DISK/CARD Saves the application software to a formatted floppy
disk or memory card. By pressing DO you enter the
name menu which enables you to give the application
software a file name on the disk/card. On the top line
a file name is displayed with a cursor under the first
character - ready for editing.
SOFT DIAL A: CURSOR Moves the cursor forward or backwards through
the name. The name can have a maximum of 8
characters.
SOFT DIAL B: LETTERS Selects a letter from A to z and inserts it in the
name over the cursor.
SOFT DIAL C: FIGURES As letters but numerical from 0 to 9.
SOFT DIAL D: SYMBOLS Inserts symbols instead of characters, e.g. blank
or space is a symbol found here.
(Press DO to confirm file name.)
LOAD MIDI Enables you to receive software updates from another
M5000 (See SAVE MIDI) or you can use TC's
M5DUMP software package which enables you to
dump software to the M5000 via an IBMtm compatible
PC with a MIDI interface installed. This package is
available from TC's bulletin board free of charge for
M5000 USER CLUB members and instructions are
implemented with the program.

Product specificaties

Merk: TC Electronic
Categorie: Niet gecategoriseerd
Model: M5000

Heb je hulp nodig?

Als je hulp nodig hebt met TC Electronic M5000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd TC Electronic

TC Electronic

TC Electronic Rush Booster Handleiding

14 November 2024
TC Electronic

TC Electronic Assimilator Handleiding

14 November 2024
TC Electronic

TC Electronic BC410 Handleiding

14 November 2024
TC Electronic

TC Electronic Master X HD Native Handleiding

23 Augustus 2024
TC Electronic

TC Electronic DVR 250 Native Handleiding

3 Juli 2024
TC Electronic

TC Electronic TC8210 Native Handleiding

7 Juni 2024
TC Electronic

TC Electronic VSS4 HD Handleiding

4 Mei 2024
TC Electronic

TC Electronic Brickwall HD Native Handleiding

31 Maart 2024
TC Electronic

TC Electronic DYN 3000 Native Handleiding

31 Maart 2024
TC Electronic

TC Electronic V550 Handleiding

1 September 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024