Tanita 1210N Handleiding

Tanita Diversen 1210N

Lees hieronder de 📖 handleiding in het Nederlandse voor Tanita 1210N (4 pagina's) in de categorie Diversen. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

CONTENTS

MODEL1210N

MODE CAL TARE ON/OFF

max.100ct・d=0.01ct0.64ozt

・d=0.0001oz

t308gr・d=

0.05gr20g・d=0.002g

MODEL1210N

MODE

CAL TARE

ON/OFF

max.100ct・d=0.01ct0.64ozt・d=0.0001ozt308gr・d=0.05gr20g・d=0.002g

MODEL1210N

MODE CALTARE

ON/OFF

max.100ct・d=0.01ct0.64ozt・d=0.0001ozt308gr・d=0.05gr20g・d=0.002g

MODEL1210N

MODE

CALTAREON/OFF

max.100ct・d=0.01ct0.64ozt・d=0.0001ozt308gr・d=0.05gr20g・d=0.002g

DEL

121

MODE

CAL TARE

ON/OFF

USA

IMPORTANT

1. Use in location where there is little vibration.

2. If the change in temperature exceeds 5¡C (10¡F), wait at least 30 minutes before use.

3. Use on a hard flat surface.

4. Keep the cover closed when weighing.

5. Do not dismantle.

6. Clean using mild detergent. Chemicals should not be used.

① Cover

② Weighing tray

③ LCD display

④ Key buttons

⑤ Test weight

⑥ Lock release button

⑦ Gem cup

⑧ Lo battery mark

⑨ Stable mark

⑩ Minus sign

  Calibration mark

 Weighing modes

  ON/OFF button

 TARE button

 CALIBRATION button

 MODE button

AC adaptor inlet

WEIGHING

CALIBRATING

1. Turn on the scale, and press the CAL button.

2. The display shows CALIb and then will flash CALIb .

3. Place the included test weight on the weighing tray. The scale will calibrate automatically.

4. The following messages will appear one after another;

CALIb End 20.000g→ →

5. Calibration is completed. Remove the test weight.

※Calibration is not completed when showing Err . Repeat calibration procedure.

PROGRAMMING AUTO POWER OFF

◆Default setting is 10 minutes.

◆The auto power off time can be programmed between 0 (=no auto power off) to 60

minutes by 10 minutes according to preference.

◆Press MODE button and ON/OFF button simultaneously when the uni t is turned off.

The unit will then show the current setting.

1. Press TARE button to increase the length (the figure goes up by 10 minutes) and press

CAL button to decrease.

2. Press MODE button to set.

TECHNICAL SPECIFICATIONS

BEFORE USE

(Fig.1) (Fig.2)

◆Whenusingwithbatteries.

1.Pressthelockreleasebutton(Fig.1).

2.Removethebatterycoverandinsert4sizeAAA(LR03)batteriesasshowninFig.2.

3.Replacethebatterycover.

◆WhenusingwithACadaptor.

1.DonotuseanyACadaptorexceptthosewiththefollowingspecification.

NAMES OF PARTS

①

②

⑦

③

④⑤

⑥

⑧

⑨

⑩



 





2.TouseACadaptor,puttheDCjackintotheinletasintheabove.

＊Before measuring, we recommend you to carry out a calibration. (→ see

"CALIBRATING")

1. Press the lock release button to open the cover (Fig.3).

2. Press the ON/OFF button to turn on the scale. Th e display will flash,

and wh en the display shows "0." and Stable mark, the scale is ready for

use.

3. Place the object to be weighed on the tray.

*If using the gem cup, remove the tray.

4. The object’s weight will be displayed.

5. In order to subtract the weight of the vessel or container, press the TARE button. "0." will

appear on the display, and when an object is placed on the scale, the weight of that object

only will be displayed.

6. In order to change the units of measurement, press the MODE button.

The units will change in the following order: g ct ozt grain→ → →

7. When you have finished weighing, press the ON/OFF button to tur n off. The scale will turn

off automatically after ten minutes of inactivity.

8. When not in use, close the cover and push back until it locks.

*If you used the gem cup, remove it and put the weighing tray back in place.

※"EEEEE" :Over Load. The object being weighed exceeds the maximum weight.

(Fig. 3)

Test weight

Capacity

Graduation

Power

Power Consumption

20g

20g / 100ct / 0.64ozt / 308gr

0.002g / 0.01ct / 0.0001ozt / 0.05gr

DC6V AAA(LR03) × 4 (included)

AC adaptor (DC6V 200m A) (Whenusingwith

12mA (max.)

*Not legal for trade.

＊OnlyuseanACadaptorwithaCEmarking.

Push

Open

Push ＋

−

＋

−

Product specificaties

Merk:	Tanita
Categorie:	Diversen
Model:	1210N

Heb je hulp nodig?

Als je hulp nodig hebt met Tanita 1210N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Diversen Tanita

Tanita 1579 Handleiding

9 December 2022

Tanita AB-140M - Abdominal Fat Analyser Handleiding

9 December 2022

Tanita AM-180 Handleiding

9 December 2022

Tanita 1210N Handleiding

9 December 2022

Tanita D-1000plus Handleiding

23 December 2022

Tanita Calorie Jump Handleiding

14 December 2022

Tanita HC-212F Breath Checker Handleiding

14 December 2022

Handleiding Diversen

Nieuwste handleidingen voor Diversen

Fysic FHP-160 Handleiding

23 Oktober 2023

Fysic FC-18 Handleiding

23 Oktober 2023

Fysic FC35 Handleiding

23 Oktober 2023

Ideen Welt Led stekkerdoos verlichting 323043-G Handleiding

17 Oktober 2023

Ideen Welt Thermo koeltas Handleiding

17 Oktober 2023

Ideen Welt Massage MV-25 Handleiding

17 Oktober 2023

Ideen Welt LED sensor LX-LD-P300 Handleiding

17 Oktober 2023

Ideen Welt ZF6865 8 LED Camping lamp Handleiding

17 Oktober 2023

Ideen Welt Muis snoerloos Handleiding

17 Oktober 2023

Ideen Welt Koffer weegscaal Handleiding

17 Oktober 2023