Tandberg Data StorageLibrary T40+ Handleiding

Tandberg Data Niet gecategoriseerd StorageLibrary T40+

Lees hieronder de 📖 handleiding in het Nederlandse voor Tandberg Data StorageLibrary T40+ (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Quick Installation Steps

For more information and complete step-by-step instructions, please refer to the StorageLibrary T40+ Series

Installation and User Guide available at www.tandbergdata.com .

Warning Although the StorageLibrary T40+ may be lifted by one person when drives, ™

power supply, and magazines are removed, for your protection and safety, we

recommend that two people lift the StorageLibrary™ T40+. All-inclusive library

weight = 38 kg / 84 lbs (2 FH drives). Empty library weight = 23.6 kg / 52 lbs (not

including drives, magazines or power supply).

Caution Please ensure the StorageLibrary T40+ is mounted in the rack before you remove

the transport screws. The transport locking screws must be removed before the

StorageLibrary T40+ can operate normally.

When following the steps below, please refer to the corresponding numbers and letters on the illustrations.

1. Please refer to the StorageLibrary T40+ Series Pass-Thru Installation Manual for instructions of how to

install the unit. To insert the StorageLibrary T40+ onto the rack-rails, please request help of another

person.

2. Before removing the locking screws, power-on the unit. The StorageLibrary T40+ will automatically eject

the magazines if the transport locking screws are mounted. Remove all magazines, remove the four

transport locking screws, and mount the rack mount ears. Re-insert the magazines.

3. Install SCSI, SAS or Fibre Channel cables.

SCSI installation:

Power-off the unit and the host system before plugging in the SCSI cables. When using more than two

SCSI drives, please refer to the StorageLibrary T40+ Series Installation and User Guide for installation

requirements.

a. Connect a SCSI cable from the host to the

1st drive (bottom SCSI connector).

b. Connect a SCSI jumper cable from 1st drive

(top SCSI connector) to the 2nd drive

(bottom SCSI connector). If required repeat

this step for all drive within the tape library.

c. Terminate the last device on the SCSI bus

using the correct SCSI terminator.

NOTE: The maximum SCSI bus length must NOT exceed 9 meters / 30 feet. Please ensure SCSI cables

and teminators are securely fitted using thumbscrews.

SAS installation:

If your library includes tape drives with SAS

interface, connect a SAS cable to each tape

drive separately and connect other end of the

SAS cable to the host.

FC installation:

If your library includes tape drives with FC

interface, connect a FC cable to each tape

drive separately and connect other end of the

FC cable to the host, switch or hub.

4. Configuring the library

a. Connect your Ethernet cable to the Ethernet

port at the rear of the library. The library

Ethernet port allows the use of the Web

Client.

b. Connect the two power cords to

the power connectors at the rear of

the library. US and European power cords

are supplied with the library. Two power

cords are required for redundant power supply.

c. Power-on the library (both switches).

d. Power up the host system.

e. Verify that each host can communicate with the library’s tape drives. If you experience problems,

please refer to the troubleshooting guide in the StorageLibrary T40+ Series Installation and User

Guide.

f. Configure your library using the library’s operator panel.

NOTE: The LTO-5 automation tape drives contain an Ethernet port which will enable new features and

functionality at a later time. For more information please refer to www.tandbergdata.com .

Table: Power Requirements

Values

Input Voltage 100 – 240 VAC (1.2 – 0.5 A)

Input Frequency 50 – 60 Hz

Inrush Current (Cold Start) Less than 15 A, 115 VAC

Less than 30 A, 230 VAC

Power Consumption Average 70 W*

Power Consumption Peak* 120 W**

* Value per StorageLibrary T40+ unit with two LTO drives.

** Maximum peak length, less than 10ms.

Product specificaties

Merk:	Tandberg Data
Categorie:	Niet gecategoriseerd
Model:	StorageLibrary T40+
Gewicht:	37700 g
Stroomvoorziening:	100 - 240 VAC, 50 - 60 Hz
Certificering:	CE, FCC, TUV/GS, ICES VCCI, BSMI, CISPR 22, C-tick, UL, C-UL, CB, GOST and EN 55022 Class A
Temperatuur bij opslag:	10 - 90 °C
Mean time between failures (MTBF):	250000 uur
Ondersteunde mediatypen:	LTO-4, LTO-3, LTO-2, LTO-1
Standaardcapaciteit:	19200 GB
Capaciteit met compressie:	38400 GB
Afmetingen (B x D x H):	446.6 x 736.6 x 177.5 mm
Montage:	Rack
Slot-type:	Mail
Bedrijfstemperatuur (T-T):	20 - 80 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 40 procent
Type product:	Opslag autolader & bibliotheek
Media type:	Tapecassette
Niet-gedetecteerd foutpercentage:	< 10(17)
Backupsnelheid (gecomprimeerde gegevens):	1700 GB/uur
Schijfeenheid:	LTO-4
Backupsnelheid (oorspronkelijke prestatie):	864 GB/uur