System Sensor SPR Handleiding

System Sensor Speaker SPR

Lees hieronder de 📖 handleiding in het Nederlandse voor System Sensor SPR (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 73 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

SS-140-000 1 I56-3108-004R

FIGURE 1. WIRING DIAGRAM:

INPUT FROM

AMPLIFIER

OUTPUT NEXT TO

DEVICE OR EOL

(+)

(–) (+)

(–)

A0380-00

PRODUCT SPECIFICATIONS

Operating Temperature Standard K Series32°F to 120°F (0°C to 49°C) –40°F to 151°F (–40°C to 66°C)

Humidity Range Standard K Series10% to 93% Non-condensing Meets NEMA 4X and IP56 rating requirements

Nominal Voltage 25 Volts or 70.7 Volts (nominal)

Maximum Supervisory Voltage 50 VDC

Speaker Frequency Range 400 - 4000 Hz

Power Settings 1/ , 41/ , 1, 2 watts2

Input Terminal Wire Guage 12-18 AWG

Dimensions for Speakers and Accessories NOTE: V suffix refers to high volume device, C suffix refers to ceiling device.

Wall Product Length Width Depth Ceiling Product Diameter Depth

SP Speaker SPC Speaker6.0˝ 5.0˝ 2.8˝ 6.8˝ 2.8˝

SPV Speaker SPCV Speaker6.0˝ 5.0˝ 2.9˝ 6.8˝ 2.9˝

Weatherproof Back Box** Weatherproof Back Box**6.5˝ 5.5˝ 2.9˝* 7.2˝ 2.9˝*

Surface Mount Skirt Surface Mount Skirt6.5˝ 5.5˝ 2.7˝* 7.2˝ 2.7˝*

*Depth above finished surface of wall or ceiling.**Weatherproof back box dimensions do not include the two mounting tabs.

Mounting Box Options

Indoor Products K Series Products

4 × 4 × 21/ or deeper8

MWBB - red wall metal weatherproof back box

MWBBW - white wall metal weatherproof back box

MWBBCW - white ceiling weatherproof back box

The indoor SP, SPV, SPC, and SPCV Series are suitable for dry and damp environments.

The “K” Series models are suitable for use in both indoor and outdoor applications.

NOTICE: This manual shall be left with the owner/user of this equipment.

The “K” models are suitable for outdoor use in wet environments with out-

door backbox supplied with the product.

GENERAL DESCRIPTION

The SpectrAlert Advance series of notification appliances offers a wide range

of indoor and outdoor speakers for wall and ceiling applications, indoors and

outdoors. They are designed to be used at either 25 or 70.7 volts, and operate

at any one for four input power levels. These products are electrically back-

ward compatible with the previous generation of SpectrAlert speakers. With

its low total harmonic distortion, the SpectrAlert Advance SP series offers

high fidelity sound output. The SpectrAlert Advance SPV series offers greater

sound output at every tap setting for applications with high ambient noise

levels. Wall and ceiling products may be used interchangeably (wall products

may be used on the ceiling and ceiling products may be used on the wall). K

Series products are designed to be used over a wider range of temperatures

and are suitable for use in wet locations.

FIRE ALARM SYSTEM CONSIDERATIONS

All wiring must be installed in compliance with the National Electrical Code

(NEC) and applicable local codes. System Sensor recommends installing fire

alarm speakers in compliance with NFPA 72, ANSI/UL1480 and NEC 760.

Electrical Wiring

1. Connect the speaker as shown in Figure 1.

NOTE: Do not loop electrical wiring under terminal screws. Wires con-

necting the device to the control panel must be broken at the device

terminal connection in order to maintain electrical supervision.

2. There are two rotary switches on the back of the product. The first switch

is used to select either 25 or 70.7 volts input. The second switch is used

to select the input power of 1/ , 41/ , 1 or 2 watts.2

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: 630/377-6495

www.systemsensor.com

INSTALLATION AND MAINTENANCE INSTRUCTIONS

SpectrAlert Advance SP and SPV Series

Dual Voltage Speakers for

Fire Protective Signaling Systems

For use with the following models: SPR, SPW, SPRV, SPWV, SPRK, SPWK, SPCW,

SPCR, SPCWV, SPCRV, and SPCWK

I56-3108-004R

Figure 2.Speaker WaTTage and VoLTage SeTTingS:

A0419-00

ShorTing Spring

NOTE: A shorting spring is provided between terminals 2 and 3 of the mount-

ing plate to enable wiring checks after the system has been wired, but prior

to installation of the final product. This spring will automatically disengage

when the product is installed, to enable supervision of the final system.

Figure 3:

SHORTING SPRING

A0381-00

TabLe 1. Sound LeVeLS For eaCh TranSFormer poWer Tap:

UL Reverberant (dBA @ 10 ft.) SP, SPC SPV, SPCV

2W 86 90

1W 83 87

1/ W 80 842

1/ W 77 814

NOTE: V suffix refers to high volume device,

C suffix refers to ceiling mount device.

CAUTION

Signal levels exceeding 130% rated signal voltage can damage the speaker.

Consequently, an incorrect tap connection may cause speaker damage. This

means that if a 25V tap is selected when a 70.7V amplifier is being used,

speaker damage may result. Therefore, be sure to select the proper taps for the

amplifier voltage/input power level combination being used.

mounTing indoor WaLL or CeiLing produCTS

1. Attach mounting plate to junction box as shown in Figures 4 and 5. The

mounting plate is compatible with 4˝ x 4˝ x 2

1/8˝ junction boxes. If using

a back box skirt or trim ring, attach the mounting plate to the skirt or

trim ring and then attach the entire assembly to the junction box (see

Figures 4, 5, 6 and 7).

2. Connect field wiring to terminals, as shown in Figure 1.

3. If the product is not to be installed at this point, use the paint cover to

prevent contamination of the mounting plate.

4. To attach product to mounting plate, remove the paint cover, then hook

tabs on the product housing into the grooves on the mounting plate.

5. Then, swing product into position to engage the pins on the product with

the terminals on the mounting plate. Make sure that the tabs on the back

of the product housing fully engage with the mounting plate.

6. Secure product by tightening the single mounting screw in the front

of the product housing. For tamper resistance, the standard captivated

mounting screw may be replaced with the enclosed Torx screw.

k SerieS mounTing

1. K Series products may be used indoors or outdoors. They must be in-

stalled using the proper SpectrAlert Advance weatherproof back box. Do

not attempt to use boxes other than those specified for use with the

product.

2. The plastic weatherproof back box is equipped with removable side

flanges for mounting. The back box may be secured directly to the wall

or ceiling using the flanges(plastic or metal back boxes) or by using the

knockout plugs(plastic back boxes). Knockout plugs are provided to

mount directly to the wall or ceiling or to a 1900 weatherproof electrical

box, see Figure 12.

3. Threaded holes are provided in the sides of the box for ¾ inch conduit

adapters. Knockout plugs in the back of the box can be used for ½ or

¾ inch rear entry. Unused holes must be sealed. Plugs and O-Rings are

provided with the box for this purpose.

4. It is the responsibility of the installer to make sure that all openings and

connections are sealed properly. Outdoor installations that are protected

from direct exposure to rain are still subject to condensation or leakage

through hidden areas, such as a soffit.

5. Water may pool on the back box due to condensation or direct exposure

to rain or snow. Use watertight fittings for all wiring connections, includ-

ing the knockout plugs on the back of the box. When using the plastic

plugs to fill unused threaded holes, make sure the O-rings supplied are

properly positioned on the plug. The plugs must be sealed with PTFE

thread seal tape.

SS-140-000 2 I56-3108-004R

UL ANechoic (dBA @ 10 ft.) SP, SPC SPV, SPCV

2W 88 93

1W 86 90

1/ W 83 872

1/ W 80 844

6. Attach the mounting plate to the weatherproof back box using the four

non-painted screws.

7. Follow steps 2-5 of the indoor mounting instructions to wire and attach

the product. The product must be mounted to the weather proof back

box using the painted screws (wall product has 4 screws, ceiling product

has 3 screws)

CAUTION

The ‘hold-in-place’ snaps are not intended to secure the product to the back

box. The product must be secured to the back box using the screws provided

Figure 4. WaLL mounT produCT WiTh Trim ring:

A0382-00

Figure 5. CeiLing mounT produCT WiTh Trim ring:

A0383-00

Figure 6. WaLL mounT produCT WiTh baCk box SkirT :

A0386-00

Figure 7. CeiLing mounT produCT WiTh baCk box SkirT :

A0385-00

SS-140-000 3 I56-3108-004R

Figure 8. ouTdoor WaLL mounT produCT WiTh pLaSTiC

WeaTherprooF baCk box:

A0384-00

Figure 9. ouTdoor CeiLing mounT produCT WiTh pLaSTiC

WeaTherprooF baCk box:

A0420-00

Figure 10. ouTdoor WaLL mounT produCT WiTh meTaL

WeaTherprooF baCk box:

A0410-00

Figure 11. ouTdoor CeiLing mounT produCT WiTh meTaL

WeaTherprooF baCk box:

A0407-00

A0424-00

Figure 12. For knoCkouTS uSe a FLaT bLade SCreWdriVer.

NOTE: Place the blade along

the edge of the slot and slowly

work your way around the slot

as you strike the srewdriver.

Product specificaties

Merk:	System Sensor
Categorie:	Speaker
Model:	SPR
Kleur van het product:	Rood
Gewicht:	- g
Breedte:	127 mm
Diepte:	71.12 mm
Hoogte:	152.4 mm
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	2 W
Certificering:	UL
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Muur-montage
Frequentiebereik:	400 - 4000 Hz
AC-ingangsspanning:	25 / 70.7 V
Relatieve vochtigheid in bedrijf (V-V):	10 - 93 procent