Synco WAir-G2-A2 Handleiding

Synco Microfoon WAir-G2-A2

Lees hieronder de 📖 handleiding in het Nederlandse voor Synco WAir-G2-A2 (2 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
RX Receiver x1 TX Transmitter x2 Carrying & Charging Box x1
Type-C to Type-C Cable x1
External Lav Mic (With Wind Muó½—ˆ) x2
3.5mm TRRS Phone Cable x1
3.5mm TRS Camera Cable x1
Mic Windshield x2
Type-C to USB-A Adapter X1
User Manual X1
1. TX Transmitter
2. RX Receiver
3. Carrying & Charging Case
â‘  External Mic Input
â‘¡ Type-C Charging Port
â‘¢ On/ Oó½—ˆ Button
â‘£ Built-in Mic
⑤ Display Screen
â‘  Type-C Charging Port / Digital Output
â‘¡ On/ Oó½—ˆ Button (Mono / Stereo / Safety Channel)
â‘¢ 3.5mm TRS Output
â‘£ 3.5mm Monitoring Port
⑤ Display Screen
â‘¥ Gain Adjustment of TX A
⑦ Gain Adjustment of TX B
⑧ Magnet Pocket Clip
⑨ Contacts
â‘  Contacts
Caring For Your SYNCO Product Product Instruction Operations
Packing List
· Please keep the product in a dry, clean, dust-free environment.
· Keep corrosive chemicals, liquids and heat source away from the
product to prevent mechanics damage.
· Use only a soft and dry cloth for cleaning the product.
· Malfunction may be caused by dropping, impact of external force.
· Do not attempt to disassemble the product. Doing so voids warranty.
· Please have the product checked or repaired by authorized technicians
if any malfunctions happened.
· Failure to follow all the instructions may result in mechanics damage.
· Warranty does not apply to human errors.
Microphone G2A2 MEGA
User Manual
Thank you for choosing SYNCO product.
Please read this manual carefully before use and follow all instructions
mentioned herein.
â‘¥ Noise Reduction
⑦ Gain Adjustment of TX/ Internal Storage
Recording Button
⑧ Magnet Pocket Clip
⑨ Contacts
â‘¡ Power Indicator â‘¢ Type-C Port
4. Display Screen
Recording
TX A
Gain of A TX
Audio Dynamic
Display of A TX
Noise Reduction on
TX Transmitter
RX Receiver
Muting
Recording Mode:
Mono/ Stereo/ Safety
Disconnected
Connecting
Connected
Audio Dynamic
Display
Power Indicator
TX B
Gain of B TX
Audio Dynamic
Display of TX B
Power Indicator
1. Power On/ Oó½—ˆ
Power On
Method 1: The TX and RX automatically turn on after taken out from the
charging Case.
Method 2:The TX and RX automatically turn on when long press the
power button for 3 seconds, and the display screen lights up.
Power Oó½—ˆ
Method 1: After put the transmitter/receiver into the charging box, the
display screen shows [charging] and enters automatic charging. After fully
charged, the display screen goes out and automatically power oó½—ˆ.
Method 2:The TX and RX automatically turn oó½—ˆ when long press the
power button for 3 seconds, and the display screen lights oó½—ˆ.
2. Pairing
Automatic Pairing
Automatically pairing after the TX/RX turns on when taken out from the
charging case.
Manual Pairing
â‘  Long press the transmitter and receiver at the same time for 3 seconds
to power oó½—ˆ .
â‘¡ After shutdown, long press the power button of the transmitter and
receiver for 8 seconds at the same time to enter the [connecting ] state.
Disconnected Connecting
Connected
â‘¢ Successfully Connected show as the picture
*Note: Before successful connection, the transmitter channel displays
A by default. The transmitter connected to the receiver ó½—‰rst is the
transmitter A, and the later one is the transmitter B.
*Note: When using an external microphone, please insert it correctly
into the microphone input jack. Only TRS interface microphones are
supported.
4. Channel output connection
â‘  3.5mm OUT output
The receiver outputs the audio signal to the recording device via either a
3.5mm TRRS phone cable or a 3.5mm TRS camera cable. Please use the
appropriate cable according to your device.
Apple Adapter (With MFI Certió½—‰cation)
3.5mm TRRS Phone Cable
3.5mm TRS Camera Cable
â‘¡ Type-C port digital output
The receiver Type-C port has a digital output function, which can directly
use the Type-C to Type-C cable to output mobile phones or computers
and other devices.
Magnet x2
3. Internal Storage Recording Function
On/Oó½—ˆ:
Long press the internal storage recording button on TX for 3 seconds to
turn on or oó½—ˆ the internal storage recording function. Once the function
is on, a red point will be displayed on the screen and will disappear once
the function is oó½—ˆ.
Red point on the RX's screen:
Internal storage recording on
Red point on RX is ó½—Šashing:
Storage is full
"!" on TX: Storage is full
Red point on the TX's screen:
Internal storage recording on
Wireless Transmission
RF Frequency Band
Working Distance
Mounting
Audio Input
Power Requirements
Battery Type
Battery Charging Time
Battery Life
Built-In Memory
Recording Hour
Wireless Transmission
RF Frequency Band
Working Distance
Latency
Mounting
Number of Audio Channels
Audio Output
Volume Adjustment
Power Requirements
Battery Type
Battery Charging Time
Battery Life
Display Screen
Dimensions
Material
Weight
Form Factor
Frequency Range
Sensitivity
Maximum SPL
Battery Type
Battery Charging Time
Charging Port
Power Requirement
Dimension
Weight
Digital 2.4GHz
2400-2483.5MHz
656ft/200m (LOS area), 164ft/50m (NLOS area)
Pocket Clip
3.5 mm TRS Mic Input
5V 1A
Built-in Lithium Battery, 400mAh
2H
8H
8GB
Approx. 24H (About 5H For Each Recording File)
Digital 2.4GHz
2400-2483.5MHz
656ft/200m (LOS area)
164ft/50m (NLOS area)
20ms
Pocket Clip
2
3.5 mm TRS Mic Output
3.5 mm TRS Headphone Output
Type-C Output
6 levels (0-3-6-9-12-15)/(0~30dB)
5V 1A
Built-in Lithium Battery, 400mAh
2H
8H
TFT Screen
52X42X17mm
ABS
39g
Built-in/External Mic
50Hz-20KHz
-35dB(±3dB,re 1V/Pa at 1 KHz)
120dB SPL(at 1KHz)
3400mAh
3.5H
Type-c
5V 1A
170*80*50mm
227g
TX Transmitter
RX Receiver
Microphone
Charging Case
6. Volume Control
â‘  Press the power button on the TX to turn on/oó½—ˆ the mute.
â‘¡ Short press the gain adjustment button of the TX to adjust the volume
for 6 levels (0-3-6-9-12-15).
â‘¢ Short press the gain adjustment of A/B TX buttons on the RX to adjust
the volume of A/B TX.
8.Switch the Channel Mode
Short press the power button on the RX to switch the mono/stereo/safety
channel mode.
Default mono mode.
9. Charging
â‘  Connect the charging cable through the Type-C port to charge the
charging case, and fully charged about 3.5 hours.
â‘¡ The TX/RX: Automatically charge through the contact point of the
charging case after put into the charging case.
â‘¢ Connect the charging cable through the Type-C port of the receiver and
the transmitter, and fully charged in about 2 hours.
10. Mic Windshield & Device Installation
11.Setting The Recording Level Correctly
TX RX
Camera devices generally have poor-quality, noisy preamps. In order to
get the cleanest signals possible, it is highly recommended that you set
the recording level on your camera quite low, 1/2 or 1/3 of it.
G2 MEGA provides variable gain control, allowing you to tailor your levels
to just about environment and recording device.
Adjust the recording level of inbuilt mics for SONY Camera
(Take A7S â…¡ for example)
Adjust the recording level of inbuilt mics for Canon Camera
(Take EOS 5D Mark â…£ for example)
Adjust the recording level of inbuilt mics for Panasonic Camera
(Take LUMIX GH5 for example)
Speci󽗉cations *Please register your warranty. Meanwhile, you are welcomed to contact us via Email:
support@syncoaudio.com
Guangzhou Zhiying Technology Co., Ltd
Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District,
Guangzhou, China, 510000
support@syncoaudio.com
www.syncoaudio.cn
Warranty Period
Warranty Exclusions and Limitations
Warranty Claim Procedure
Thank you for purchasing SYNCO products.
1. Customers are entitled to free replacement or repair service in case of
quality defect(s) found in the product under normal use within 30 days
upon receipt of the product.
2. Original SYNCO products are entitled to 12-month limited warranty
service. The warranty period begins on the date of purchase of brand new,
unused products by the ó½—‰rst end-user.
Within the warranty period, if product defect or failure is attributable to
material defection or technological problem, the defective product or
defective part will be repaired or replaced without charge (service and
materials fee).
Faults resulted from inappropriate use of a product without following its
operation speci󽗉cation:
1. Artió½—‰cial damage, e.g. crash, squeeze, scratch, or soaking
2. Modió½—‰cations to a product by its user or a third party without prior
written consent of SYNCO, e.g. replacement of element or circuit, label
alteration
3. The code on product is inconsistent with that of warranty certió½—‰cate, or
the code on the product or warranty certió½—‰cate is altered or torn oó½—ˆ
4. All consumable accessory attached to a product, like cable, wind muó½—ˆ,
battery
5. Faults as a result of force majeure, such as ó½—‰re, ó½—Šood, lightning, etc.
1. If failure or any problem occurs to your product after purchase, please
contact a local agent for assistance, or you can always contact SYNCO’s
customer service through email at support@syncoaudio.com.
2. Please retain your sales receipt and warranty certió½—‰cate as proof of
purchase. If any of these documents is missing, only sales return or
chargeable service will be provided.
3. If the SYNCO product is out of the warranty coverage, the service and
the parts cost will be charged.
Warranty
Product Model:
Date of Purchase:
Serial Number:
Malfunction Description :
Buyer Name:
Buyer Telephone :
Buyer Mail :
Buyer Address :
Dealer :
Dealer Telephone :
Delivery Date :
Cause of Malfunction :
Maintenance Personnel :
Malfunction Processing :
WARRANTY CERTIFICATE
Display Screen
Dimensions
Material
Weight
TFT Screen
52X42X17mm
ABS
39g
5. Real-time monitoring
The 3.5mm monitoring port of the receiver supports digital monitoring,
which can simultaneously monitor the sound source of the transmitter
and the input sound source of the device.
3.5mm Monitoring Jack
Headphone Impedance: under 100 Ω
*Note: When connecting the computer, enter the sound Settings and set
the input microphone to SYNCO G2 MEGA to use G2 MEGA recording; Set
the output speaker to SYNCO G2 MEGA to use real-time ear return in the
receiver listening interface.
7. Noise Cancellation
Short press the noise cancellation button on the transmitter to switch
between noise-control modes:
â‘  Noise Cancellation Oó½—ˆ
â‘¡ Low-Level Noise Cancellation
â‘¢ High-Level Noise Cancellation
Noise Cancellation Oó½—ˆHigh-Level Noise
Cancellation
Low-Level Noise
Cancellation


Product specificaties

Merk: Synco
Categorie: Microfoon
Model: WAir-G2-A2

Heb je hulp nodig?

Als je hulp nodig hebt met Synco WAir-G2-A2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Microfoon Synco

Handleiding Microfoon

Nieuwste handleidingen voor Microfoon