Sunding SD-548C Handleiding
Sunding
Fietscomputers
SD-548C
Lees hieronder de π handleiding in het Nederlandse voor Sunding SD-548C (1 pagina's) in de categorie Fietscomputers. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/1
Sunding Bicycle Computer
SD-548C (14Functions)
FUNCTIONS
- SPD CURRENT SPEED
- ODO ODOMETER οΌ0.00 99999km/m)1ο½
- DST TRIP DISTANCE
- MXS MAXIMUM SPEED
- AVS AVERAGE SPEED
- TM ELAPSED TIME .
- CLK CLOCK 12H/24H οΌ οΌ
- SCAN
- β+β β β COMPARATOR οΌ
- SETTING SPEED SCALE km/h,m/h οΌ οΌ
- SETTING TYRE CIRCUMFERENCE : 0mm οΌ ο½
9999mm οΌ
- SETTING THE LAST VALUE OF ODOMETER/ODO
- FREEZE FRAME MEMORY
- AUTO ON/OFF
Computer Battery Installation
Remove the battery cover from the bottom of the computer
by using a ο¬at blade screwdriver, install one CR2032
battery with the positive (+) pole facing the battery cover
and replace the cover. Should the LCD show irregular
ο¬gures, take out the battery and reinstall it.
Sensor Transmitter Battery Installation
Remove the battery cover
from the bottom of the
computer by using a ο¬at blade
screwdriver, install one 23A
12V battery with the positive
(+) pole facing the battery
cover and replace the cover.
Should the LCD show
irregular ο¬gures, take out the battery and re-install it.
Sensor Transmitter
Attach the sensor transmitter to the left fork blade, the
distance between computer and the sensor can not exceed
60cm, the closer the batter. Using the shims to adjust the
diameter, and using the cable
ties(show below) to tie it with the
fork. Position the sensor
transmitter and magnet as shows,
make sure that the arc of the
magnet intersects the alignment mark on the sensor
transmitter with 1.5mm clearance.
Mounting Shoe
Attach the mounting shoe with the cable ties to the
handlebar, adjust
the mounting shoe on the handlebar with
the shims to
hold its position
.
Computer
Attach the computer to the mounting shoe by sliding the
unit until it snaps ο¬rmly into its postion. To remove it, press
the button on it in the opposite direction.
To check for proper speed function and sensor alignment,
spin the front wheel with computer in speed mode. Adjust
the position of sensor and magnet when there is no or weak
reaction.
Wheel Size Input
β2060β appears on the screen when the battery has been
installed, with one ο¬gure ο¬ashing,choose the correct wheel
circumference from the table below.Press RIGHT button to
advance digits as needed and LEFT button to conο¬rm and
advance. (The circumference ranges 0m 9999mm), press mο½
LEFT button to enter KM/M mode.
SettingοΌ
οΌοΌ
οΌ οΌkm/hοΌοΌ
οΌ οΌ/οΌοΌ
οΌ οΌm/hοΌοΌ
οΌ
Press the RIGHT button to choose km/h or
m/h. Press the LEFT button to enter
CLOCK mode.
CLK Mode(12H/24H)
In CLOCK Mode, press the LEFT button
for 3 seconds to enter 12/24H selection.
Re-press the LEFT button for 12/24
exchanging. Press the RIGHT button to
enter Hour setting mode, when the ο¬gure
indicating HOUR start to ο¬ash, press the LEFT button to
adjust it.
Continue to press the RIGHT button to enter Minute setting
mode, when the ο¬gure indicating MINUTE start to ο¬ash,
press the LEFT button to adjust it and RIGHT button to
conο¬rm, press the RIGHT button again to ODO mode.
Setting the Last value of
Odometer
In ODO mode, press the LEFT button
for 2 seconds to set the ODO value,
its initial value is 0000.0. when one
figure flashing, press RIGHT button to adjust it and
LEFT button to confirm it and start to set the next
figure.(after re-install the battery, latest value can
be inputted according to the value exists before the
battery is re-installed).
Reset of Mileage Parameter
In ODO mode, press and hold both RIGHT and LEFT
button simultaneously for 3 seconds to clear the tire
circuference and (km/m) setting, The user need to reset the
tire circumference and (km/m), the original ODO value and
CLOCK will remain unaffected.
Speedometer
Speed is shown all the time on the screen, its maximum
reading is 99.9km/h(m/h), and itβs accurate to +/- 0.1km/h
(m/h).
Speed Comparator
During riding , β β+ and -β β indicates the current speed is
higher or lower than average speed(AVS) .
Odometer
In ODO mode , the total distance is
indicated on the screen, its mileage
range is 0.00 99999km(m). the 1 ο½
display will be back to 0 when value
exceeds its maximum limit, press the RIGHT button to enter
DST mode..
Trip Distance (DST)
In DST mode, the distance for one trip
is indicated on the bottom line. DST
ranges from 0.001 9999km(m), when ο½
the value exceed the range limit, it
restarts from 0 automatically. Both the time and the
distance records will be cleared when the time of one trip
exceed the range limits.
press the LEFT button for 5 seconds to clear the records of
DST,MXS,AVS and TM.
Press the RIGHT button to enter MXS mode.
Maximum Speed (MXS)
In MXS mode, maximum speed is
indicated on the bottom line. Press the
LEFT button for 5 seconds to clear the
records of MXS,DST,AVS and TM.
Press the RIGHT button to enter AVS mode.
Average Speed
In AVS mode, average speed is
indicated on the bottom line. Press the
LEFT button for 5 seconds to clear the
records of AVS,DST,MXS and TM.
Press RIGHT button to enter TM mode.
Trip Time
In TM mode, trip time is indicated on
the bottom line.TM ranges 0 :00 :00ο½
99 :59 :59. It will be back to 0 when
value exceed the limits.
Press the LEFT button for 5 seconds to clear the records of
TM, DST,MXS and AVS.
Press the RIGHT button to enter SCAN mode.
SCAN
In Scan mode , DST, MXS, AVS and TM mode are
indicated in turn every 4 seconds.
Press the RIGHT button to enter CLOCK Mode.
Sleep Mode
If no signal has been inputted for 300 seconds, computer
will enter into Sleep Mode, and CLK value remains. It will
turn back to the former mode with all the data collected
when any signal is inputted or any button is pressed.
FREEZE FRAME MEMORY
Press the LEFT button in any time will enter into freeze
frame memory mode. Flashing TM data will appear on the
screen. Press the RIGHT button to view the records of DST,
MXS, AVS and TM.
Press the LEFT button to end it.
Buttons Instruction
Press the RIGHT button to choose any mode below :
ODO, DST, MXS, AVS, TM, SCAN DST MXS AVSοΌ γ γ γ
TM and CLOCK. Itβs unnecessary to press the LEFT οΌ
button except choosing the Freeze frame Memory mode.
In Freeze Frame Momery mode, press the RIGHT button,
several data will display, re-press LEFT button to turn back
to other modes.
Malfunctions and Problems
Malfunctions Problems
No speedometer
Improper magnet/sensor alignment
Distance between computer and
sensor transmitter exceed 60cm
Low battery voltage of sensor
transmitter or computer.
Short distance of
the transmitter or
no receiving
Lower battery voltage, need to
change for a new one.
Display Abnormal
ο¬gures Too much Electromagnetic
interference around
Inaccurate value is
indicated Improper input, such as wheel
circumference.
Slow display
re spon se
Temperature exceeds operating
limits(0βο½ β55 ).
Black display
Temperature too high, or put in
direct sunlight for too long time.
Need take back to shadow place for
a period.
Weak display Poor battery contact or dead battery
Display shows
irregular ο¬gures
Take out battery and re-install it
after 10 seconds.
Sensor without
reaction
Put off the insulation ο¬lm of the
sensor transmitter
Accessories
TIRE SIZE
CIRC TIRE SIZE CIRC
700c x 38mm 2180 26ββ x 2.25ββ 2115
700c x 35mm 2168 26ββ x 2.1ββ 2095
700c x 32mm 2155 26ββ x 2.0ββ 2074
700c x 30mm 2145 26ββ x 1.9ββ/1.95ββ 2055
700c x 28mm 2136 26ββ x 1.75ββ 2035
700c x 25mm 2124 26ββ x 1.5ββ 1985
700c x 23mm 2105 26ββ x 1.25ββ 1953
700c x 20mm 2074 26ββ x 1.0ββ 1913
700cTubulari 2130 24ββ x 1.9ββ/1.95ββ 1916
650c x 23mm 1990 20ββ x 1-1/4ββ 1618
650c x 20mm 1945 16ββ x 2.0ββ 1253
27ββ x 1-1/4ββ 2161 16ββ x 1.95ββ 1257
27ββ x 1-1/8ββ 2155 16ββ x 1.5ββ 1206
26ββ x 2.3ββ 2135
Product specificaties
| Merk: | Sunding |
| Categorie: | Fietscomputers |
| Model: | SD-548C |
Heb je hulp nodig?
Als je hulp nodig hebt met Sunding SD-548C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Fietscomputers Sunding
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
Handleiding Fietscomputers
- Fietscomputers Asaklitt
- Fietscomputers Assize
- Fietscomputers Avenir
- Fietscomputers Bikemate
- Fietscomputers Boardman
- Fietscomputers Bontrager
- Fietscomputers Bryton
- Fietscomputers Btwin
- Fietscomputers Echowell
- Fietscomputers Falk
- Fietscomputers Filzer
- Fietscomputers Halfords
- Fietscomputers Pro
- Fietscomputers Prophete
- Fietscomputers Sigma
- Fietscomputers Trek
- Fietscomputers Trelock
- Fietscomputers VDO
- Fietscomputers VETTA
- Fietscomputers Crivit
- Fietscomputers Blackburn
- Fietscomputers Contec
- Fietscomputers BBB
- Fietscomputers Cateye
- Fietscomputers Cordo
- Fietscomputers CicloSport
- Fietscomputers Kathmandu
- Fietscomputers One
Nieuwste handleidingen voor Fietscomputers
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022