Sun Joe 24V-AGR100 Handleiding

Sun Joe Niet gecategoriseerd 24V-AGR100

Lees hieronder de 📖 handleiding in het Nederlandse voor Sun Joe 24V-AGR100 (40 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/40

Original instructions.

*Initial no-load voltage, when fully charged, peaks at 24

volts; nominal voltage under typical load is 21.6 volts.

SAVE THESE INSTRUCTIONS

A Division of Snow Joe, LLC Model 24V-AGR100 Form No. SJ-24V-AGR100-880E-M

OPERATOR’S MANUAL

24V*CORDLESS EARTH AUGER

550 W | 6-IN

30-IN AUGER BIT

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Always follow these safety guidelines. Failure to do so may

result in electric shock, fire and/or serious injury.

Product Description

This cordless earth auger is intended for noncommercial use only.

The auger is designed to dig holes in the ground. It is not

suitable for use on ice. The recommended maximum depth for

this auger is approximately 30" (76 cm).

General Safety

mWARNING! This tool is not intended for use by children

or by unassisted, unsupervised persons whose physical,

sensory or mental capabilities prevent them from using it

safely. Children should be supervised to ensure that they do

not play with the tool.

Before starting up your tool, please check it carefully for any

defects. If you find any, do not start up your tool. Instead,

contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

mWARNING! When using the power tool, basic safety

precautions should always be followed to reduce the risk of

fire, electric shock, and personal injury. These include:

• Stay alert – Watch what you are doing. Use common

sense. Do not operate the tool when you are tired or under

the influence of drugs, alcohol, or other medication.

• Know your product – Know how to start and stop the

tool. Be thoroughly familiar with the controls and ensure

they are functioning properly.

• Use the right tool – Do not use this tool for any job

except for what it's intended for.

• Prevent unintentional starting – Ensure the switch is in

the off-position before connecting to battery pack, picking

up or carrying the appliance. Carrying the appliance with

your finger on the switch or energizing appliance that have

the switch on invites accidents.

• Do not force the tool – It will perform better with less

likelihood of personal or mechanical injury if it is used at

the rate for which it was designed.

• Moving parts – Keep hands and feet away from moving

parts. Keep a firm grip on both handles at all times during

operation to avoid loss of control.

• Personal protective equipment – Always use eye

protection, hearing protection and protective covering to

contain long hair.

• Dress properly – Do not wear loose clothing or jewelry, as

such articles can become caught in moving parts.

• Avoid slipping – Maintain proper footing and balance

at all times to avoid slipping or falling. Wear non-slip

footwear to improve your footing on slippery surfaces.

• Avoid water - Do not expose the tool to rain, damp or wet

conditions. Do not immerse in water. Water entering the

unit will increase the risk of electric shock.

• Noise and vibrations – If the tool should start to vibrate

abnormally, stop the tool and inspect it thoroughly for

damage.

Work Area Safety

• Work area – Always inspect the area where the tool is to

be used and operate it in a well-lit environment. Do not

start using the product until you have a clear work area

and secure footing.

• Avoid dangerous environments – Do not operate the

tool in gaseous or explosive environments or use it near

flammable or combustible materials. Remove all objects

such as cords, lights, wire, or loose string which can

become entangled in the cutting blade and create a risk of

serious personal injury.

• Utility lines – Never operate tool in the vicinity of

underground electric, gas, water or telephone lines.

• Keep children, bystanders, and pets away –

All bystanders, including pets, should be kept a safe

distance away from the work area.

Maintenance + Storage

mWARNING! Do not use detergents, acids, alkaline

solutions, bleaches or solvents such as acetone to clean your

tool. These substances may damage the plastic housing of the

machine.

• Inspect the tool – Before use, visually inspect the tool for

any loose fasteners or damaged parts.

• Replacement parts – Inspect the tool for worn, missing,

or damaged parts. When servicing this unit, use only

identical replacement parts. Replace or repair damaged

parts immediately.

• Store indoors – When not in use, the tool should be

stored indoors in a dry place out of the reach of children.

• Maintain Appliance With Care – Keep cutting edge sharp

and clean for best performance and to reduce the risk of

injury. Follow instructions for changing accessories. Keep

handles dry, clean, and free from oil and grease.

Auger Safety Warnings

• Replace auger pin if it is bent or damaged. Replace

augers if cracked, bent, or damaged in any way. Operating

the tool with a damaged auger can result in serious injury.

• Be sure the auger bit and handles are properly installed and

securely fastened. Failure to do so can cause serious injury.

• Use only the manufacturer’s replacement augers. Do not

use any other attachment.

• Do not modify the product in any way or use it to power

any attachments or devices not recommended by the

manufacturer.

• Hold the tool with both hands at the intended handles.

Never use the auger with the handles above waist level.

Operation above the waist restricts control of the auger

and may increase the risk of injury.

• Before starting the product, make sure the bit is not

contacting any object.

• Do not touch the auger bit when the product is switched

on. Keep all parts of the body away from the auger. The

auger will continue to move after the switch is turned off.

A moment of inattention while operating the auger may

result in serious personal injury.

• If the auger bit jams, stop the product immediately.

• Do not use the product when there is a possibility of

thunderstorm or lightning. Store the product safely

indoors.

• Hold the auger tool by insulated gripping surfaces only,

because the auger may contact hidden wiring. The auger

contacting a “live” wire may make exposed metal parts

of the auger “live” and could give the operator an electric

shock.

Battery & Charger

Safety Instructions

We pay a great deal of attention to the design of every battery

pack to ensure that we supply you with batteries that are safe,

durable and have a high energy density. The battery cells have

a wide range of safety devices. Each individual cell is initially

formatted and its electrical characteristic curves are recorded.

This data is then used exclusively to be able to assemble the

best possible battery packs.

Despite all the safety precautions, caution must always be

exercised when handling batteries. The following points must

be obeyed at all times to ensure safe use. Safe use can only

be guaranteed if undamaged cells are used. Incorrect handling

of the battery pack can cause cell damage.

IMPORTANT! Analysesconrmthatincorrectuseandpoor

care of high-performance batteries are the main factors

responsible for product damage and/or personal injury.

mCAUTION! To reduce the risk of injury, use only official

24V iON+ designated chargers and battery packs. The use of

other batteries or chargers poses a risk of fire, personal injury

and damage.

mWARNING! Do not use a battery pack or product

that has been damaged or modified. Damaged or modified

batteries may exhibit unpredictable behavior resulting in fire,

explosion or risk of injury.

Do not modify or attempt to repair the product or the battery

pack except as indicated in the instructions for use and care.

Do not wire a battery pack to a power supply or car cigarette

lighter, as such misuse will permanently disable or damage the

battery pack.

Haveyourbatterypackservicedbyaqualiedrepairperson

using only identical replacement parts. This will ensure that the

safety of the battery pack is maintained.

mWARNING! To reduce the risk of electric shock,

always unplug the charger before performing any cleaning or

maintenance. Do not allow water to flow into the charger. Use

a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of

electric shock.

• Remove battery – Remove the battery pack from the tool

when not in use, before servicing, or before performing

any other maintenance task. Never leave the tool

unattended while switched on. In the event of an accident

or breakdown, switch off the tool immediately.

• Avoid dangerous environments – Do not charge the

battery pack in rain, snow or in damp or wet locations.

Do not use the battery pack or charger in the presence

of explosive atmospheres (gaseous fumes, dust or

flammable materials) because sparks may be generated

when inserting or removing the battery pack, which could

lead to a fire.

NOTE: The safe temperature range for the battery is

41°F (5°C) to 105°F (40.5°C). Follow all charging

instructions and do not charge the battery pack or

appliance outside of the temperature range specified in

the instructions. Charging improperly or at temperatures

outside of the specified range may damage the battery

and increase the risk of fire. Do not charge the battery

outside in freezing weather; charge it at room temperature.

• Charge in a well-ventilated area – Do not block the

charger vents. Keep them clear to allow for proper

ventilation. Do not allow smoking or open flames near a

charging battery pack. Vented gases may explode.

• Maintain charger cord – When unplugging the charger,

pull the plug, not the cord from the receptacle to reduce

the risk of damage to the power cord. Never carry the

charger by its cord. Keep the cord away from heat, oil and

sharp edges. Make sure the cord will not be stepped on,

tripped over or subjected to damage or stress when the

charger is in use. Do not use a charger with a damaged

cord or plug. Replace a damaged charger immediately.

• Do not use an extension cord unless it is absolutely

necessary – Using the wrong, damaged or improperly

wired extension cord poses a risk of fire and electric

shock. If an extension cord must be used, plug the

charger into a properly wired 16 gauge or larger extension

cord with the female plug matching the male plug on the

charger. Make sure that the extension cord is in good

electrical condition.

• Do not burn or incinerate battery packs – Battery packs

may explode, causing personal injury or damage. Toxic

fumes and materials are created when battery packs are

burned.

• Do not crush, drop or damage battery packs – Do not

use the battery pack or charger if they have sustained

a sharp blow, been dropped from a height of more than

3 feet (1 meter), run over or have been damaged in any

way. Even if the housing of the battery pack appears to be

undamaged, the battery cells inside the battery may have

suffered serious damage. In such instances, please read

the waste disposal information for proper battery disposal.

• Do not disassemble – Incorrect reassembly may pose

a serious risk of electric shock, fire or exposure to toxic

battery chemicals. If the battery or charger are damaged,

contact an authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563) for assistance.

• Battery chemicals may cause serious burns –

Never let a damaged battery pack contact the skin,

eyes or mouth. If damaged, battery chemicals will react

violently with air; use rubber or neoprene gloves to safely

dispose of the battery. If skin is exposed to battery

chemicals, wash the affected area with soap and water. If

eyes are exposed to battery chemicals, immediately flush

with water for 20 minutes and seek medical attention.

Remove and dispose of contaminated clothing.

• Risk of short circuit – A battery pack will short circuit if

a metal object makes a connection between the positive

and negative contacts on the battery pack. Do not place a

battery pack near anything that may cause a short circuit,

such as paperclips, coins, keys, screws, nails and other

metallic objects. A short-circuited battery pack poses a

risk of fire and severe personal injury.

• Store your battery pack and charger in a cool, dry

place – Ideally, store the battery pack at 59°F (15°C) and

charged to at least 40%. Do not store the battery pack or

charger where temperatures may exceed 105ºF (40.5ºC),

such as in direct sunlight or inside a vehicle, or where

temperatures may drop below 41°F (5°C).

NOTE: Prevent the battery pack from freezing. Battery

packs that were stored below 32°F (0°C) for more than 60

minutes must be discarded.

• Charge before use – The battery pack supplied with your

power tool is only partially charged. The battery has to be

fully charged before using the product for the first time.

• Battery Aging – Lithium-ion batteries are subject to a

natural aging process. The battery pack must be replaced

at the latest when its capacity falls to just 80% of its

capacity when new. Weakened cells in an aged battery

pack are no longer capable of meeting the high power

requirements needed for the proper operation of your

power tool, and therefore pose a safety risk.

• Do not exhaustively discharge battery packs –

A complete discharge will damage the battery cells. The

most common cause of exhaustive discharge is lengthy

storage. Stop working as soon as the performance of the

battery falls noticeably or the electronic protection system

triggers. For optimum battery performance, charge the

battery pack frequently. Place the battery pack in storage

only after it has been fully charged.

• Do not overload battery packs – Protect the product and

batteries from overloading. Overloads will quickly result in

overheating and cell damage inside the battery housing

even if it is not apparent externally. For safety reasons,

the integrated protective cutoff will activate to switch off

the equipment. After regular use, allow the battery pack

to cool to room temperature before inserting it into the

charger to recharge.

IMPORTANT! Do not attempt to turn on the product if the

protective cut-off has been activated. This may damage

the battery pack.

• Do not expose the battery pack or appliance to fire or

excessive temperature. Exposure to fire or temperature

above 265°F (130°C) may cause explosion.

• Outlet voltage – Please check the data marked on the

rating plate of the battery charger. Be sure to connect the

battery charger to a power supply with the voltage marked

on the rating plate. Never connect it to a different mains

voltage.

• Charger use – Do not use the supplied battery charger to

charge other types of battery packs or tools.

• Do not overcharge battery packs – Do not exceed

the maximum charging times. Frequently overcharging

the battery pack will result in cell damage. Do not leave

batteries in the charger for days on end.

• Battery pack abnormalities – Do not use batteries that

have suffered swelling or deformation or those that exhibit

other atypical symptoms (gassing, hissing, cracking, etc.).

• Electrostatic discharge – When handling batteries, be

wary of electrostatic charge. Electrostatic discharges can

damage the electronic protection system and the battery

cells. To avoid electrostatic discharges, never touch the

battery terminals.

Product specificaties

Merk:	Sun Joe
Categorie:	Niet gecategoriseerd
Model:	24V-AGR100

Heb je hulp nodig?

Als je hulp nodig hebt met Sun Joe 24V-AGR100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Sun Joe

Sun Joe BDL-A0075 Handleiding

11 Augustus 2023

Sun Joe SJ-SHLV06 Handleiding

11 Augustus 2023

Sun Joe SJ-SHLV07 Handleiding

11 Augustus 2023

Sun Joe 24V-WB1000 Handleiding

3 Juli 2023

Sun Joe TJW24C-RM Handleiding

16 Juni 2023

Sun Joe SJ-WBFG Handleiding

16 Juni 2023

Sun Joe 24V-AJC-LTW-PRP-RM Handleiding

2 Juni 2023

Sun Joe 24V-X2-TLR14-CT Handleiding

26 Mei 2023

Sun Joe PJ3600C-RM Handleiding

18 Mei 2023

Sun Joe 24V-X2-TLR14-RM Handleiding

9 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo VPPI Handleiding

21 November 2024

Festo VAVE-P17-TP-5YL1-P Handleiding

21 November 2024

Festo SD-SUB-D-BU9 Handleiding

21 November 2024

Festo SAMH-F12-MK Handleiding

21 November 2024

Festo SFAB Handleiding

21 November 2024

Festo SFAH Handleiding

21 November 2024

Festo DRRD-12 Handleiding

21 November 2024

Festo SDE3 Handleiding

21 November 2024

Festo SFTE Handleiding

21 November 2024

Festo CRVZS-5 Handleiding

21 November 2024