StarTech.com U1-USB-ISOLATOR Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com U1-USB-ISOLATOR (2 pagina's) in de categorie Netwerkkaart/adapter. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support
Manual Revision: October 16, 2024
Product ID
U1-USB-ISOLATOR
Top View
Bottom View
1-Port Industrial USB 2.0 Galvanic Isolator - Up to 6000V
Port/Connector Function
1USB LED
Solid Blue: Indicates there’s a connected to the USB Device
Isolated USB Device Port
Note: The Host Computer must detect the connected USB
Device before the LED turns on.
O: No connected on the USB Device Isolated USB
Device Port
2Aux Power LED Solid Green: External power is being supplied
O: No external power is being supplied
3
Isolated USB
Device Port
(Downstream)
USB Type-A port. Provide up to 250mA output when not
using the optional power adapter
USB 2.0 compliant
Supports 1.5Mbps and 12Mbps only
4USB Host Port
(Upstream)
USB Type-B port
Connect to the using the supplied Host Computer USB-B
to USB-A Cable
5DC Power Port
(Optional) If the requires more than Isolated USB Device
250mA and less or equal than 500mA, an external Power
Supply (not included) is required
6V DC 2A Power Adapter Recommended
Type M barrel plug: Ø 5.5x2.1x9.5mm. Center tip positive
6DIN Rail
Mounting Point Use to secure the included DIN Rail Mounting Kit
7Guide Peg Helps to install the so it can be DIN Rail Mounting Kit
installed only in one way
Package Contents
USB Isolator x 1
3ft (0.9m) USB-B to USB-A Cable x 1
Adhesive Strip x 1
DIN Rail Mounting Kit x 1
Quick-Start Guide x 1
Requirements
For the latest manuals, product information, technical specications, and declarations of
conformance, please visit: www.StarTech.com/U1-USB-ISOLATOR
*Product may vary from image
3
6
1 2
4
5
7
Regulatory Compliance
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a dierent circuit than the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the device. If shielded interface cables are included with the product, or if additional components or accessories are
designated for use with the installation, they must be used to ensure compliance with FCC regulations.
ISED Statement / Déclaration d’ISDE
CAN ICES-003(B) / NMB-003(B)
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to .
www.startech.com/warranty
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Surface Mounting (optional)
1. Remove one of the protective backings from the .Adhesive Strip
2. Attach the to the back of the by applying Adhesive Strip USB 2.0 Galvanic Isolator
light pressure for a few seconds.
3. Remove the remaining protective backing from the .Adhesive Strip
4. Firmly attach the to a clean at surface.USB 2.0 Galvanic Isolator
Phillips head screwdriver
Available USB-Type A port on the Host Computer
(Optional) 6V DC Power Supply with Type M Barrel Plug
Installation
1. Connect the side of the to the . USB-Type B USB-B to USB-A Cable USB Host Port
Connect the other end of the cable to an available port on the USB Type-A Host
Computer.
Note: No drivers or additional software is needed for the USB 2.0 Galvanic Isolator.
2. Connect an to the .USB device Isolated USB Device Port
DIN Rail Mounting (optional)
1. Use the at the bottom of the to align the Guide Peg USB 2.0 Galvanic Isolator
DIN Rail Mounting Kit Phillips Head Screwdriveinto is correct position. Use a r to
install the self-tapping screw and secure the . (Figure 1) DIN Rail Mounting Kit
2. Mount the r by inserting the onto theUSB 2.0 Galvanic Isolato Mounting Plate DIN
Rail DIN Rail at an angle, starting from the top then push against the . (Figure 2)
Quick-Start Guide
Figure 2
Figure 1


Product specificaties

Merk: StarTech.com
Categorie: Netwerkkaart/adapter
Model: U1-USB-ISOLATOR

Heb je hulp nodig?

Als je hulp nodig hebt met StarTech.com U1-USB-ISOLATOR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Netwerkkaart/adapter StarTech.com

Handleiding Netwerkkaart/adapter

Nieuwste handleidingen voor Netwerkkaart/adapter