StarTech.com PEX1P2 Handleiding

StarTech.com Printer PEX1P2

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com PEX1P2 (2 pagina's) in de categorie Printer. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: September 11, 2020

Product Diagram (PEX1P2)

Front Angle View

Port Function

1Parallel Port • Female DB-25 Parallel Port

2Bracket • Congurable for and Full Prole Low Height

installations

3PCIe p1-x1 Connector • Connect the to the Parallel Adapter Card PCI

Express Slot Computer in the

Requirements

For the latest requirements, please visit:

www.startech.com/PEX1P2.

• Computer with an available PCI Express slot (x1)

Tools

• Small Phillips Head Screwdriver

Hardware Installation

Warning: Parallel Adapter Cards can be damaged by static electricity. Make sure

that the is properly grounded before they open the or touch Installer Computer Case

the . The should wear an when Parallel Adapter Card Installer Anti-Static Strap

installing any computer component. If an is not available, discharge Anti-Static Strap

any built-up static electricity by touching a large for several Grounded Metal Surface

seconds. Only handle the by its edges and do not touch the Parallel Adapter Card

gold connectors.

1 Port PCI Express Dual Prole Parallel Adapter Card - SPP/EPP/ECP®

Installing the Low Prole Bracket

By default the is attached to the . Full Prole Bracket Parallel Adapter Card

Depending on the system conguration it may be necessary to remove the Full Prole

Bracket Low Prole Bracket and replace it with the (included).

1. Using a , remove the two securing Small Phillips Head Screwdriver Bracket Screws

the to the .Full Prole Bracket Parallel Adapter Card

2. Align the on the with the on the Screw Holes Parallel Adapter Card Screw Holes

Low Prole Bracket Parallel Adapter Card. Making sure the is sitting on-top of the

Screw Holes Low Prole Bracket on the .

3. Insert the through the and into the Bracket Screws Parallel Adapter Card Screw

Holes Low Prole Bracket on the .

4. Using the , tighten the being Small Phillips Head Screwdriver Bracket Screws,

careful not to over-tighten.

Installing the Parallel Adapter Card

1. Turn o the and any that are connected Computer Peripheral Devices

(e.g. printers, external hard drives, etc.).

2. Unplug the from the rear of the and disconnect any Power Cable Computer

Peripheral Devices that are connected.

3. Remove the from the . Cover Computer Case

Note: Consult the documentation that came with the for details about Computer

how to do this safely.

4. Locate an open (x1) and remove the corresponding PCI Express Slot Metal Cover

Plate Computer Case Metal Cover Plate from the rear of the . In most instances, the

is attached to the rear of the with a single . Save this Computer Case Screw Screw

for the next step.

5. Gently insert the into the open and fasten Parallel Adapter Card PCI Express Slot

the to the rear of the using the from step 4. Bracket Computer Case Screw

6. Place the back onto the . Cover Computer Case

7. Reconnect the to the rear of the .Power Cable Computer

8. Reconnect all of the that were disconnected in step 2.Peripheral Devices

9. Connect a to the on theSPP/EPP/ECP Peripheral Device Parallel Port Parallel

Adapter Card.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: fr.startech.com

DE: de.startech.com

ES: es.startech.com

NL: nl.startech.com

IT: it.startech.com

JP: jp.startech.com

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

4490 South Hamilton

Road

Groveport, Ohio

43125

U.S.A.

Software Installation

Driver Installation

You can download the latest from the StarTech.com website: Drivers

www.startech.com/PEX1P2.

Navigate to the tab to locate the . Follow the instructions Drivers/Downloads Drivers

included with the . Driver Files

Product specificaties

Merk:	StarTech.com
Categorie:	Printer
Model:	PEX1P2
Kleur van het product:	Black, Steel
Gewicht:	42 g
Breedte:	110 mm
Diepte:	210 mm
Hoogte:	120 mm
Gewicht verpakking:	133 g
Breedte verpakking:	143 mm
Diepte verpakking:	170 mm
Hoogte verpakking:	30 mm
Gebruikershandleiding:	Ja
Materiaal:	Staal
Duurzaamheidscertificaten:	CE, RoHS
Intern:	Ja
Ondersteunt Linux:	Ja
Mean time between failures (MTBF):	26297 uur
Hostinterface:	PCIe
Meegeleverde drivers:	Ja
Ondersteunde server operating systems:	Windows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016, Windows Server 2019
Montagebeugels meegeleverd:	Ja
Chipset:	PLX/Oxford - OXPCIe952
(Buitenste) hoofdverpakking hoogte:	330 mm
(Buitenste) hoofdverpakking breedte:	610 mm
(Buitenste) hoofdverpakking lengte:	400 mm
Hoeveelheid per (buitenste) hoofdverpakking:	80 stuk(s)
Overdrachtssnelheid:	2.5 Mbit/s
Parallelle poort(en):	1
Code geharmoniseerd systeem (HS):	84733020
Uitbreidingskaartstandaard:	PCIe 1.0a
Output interface:	Parallel