StarTech.com D130-DECIBEL-METER Handleiding
StarTech.com
Geluidsniveaumeter
D130-DECIBEL-METER
Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com D130-DECIBEL-METER (6 pagina's) in de categorie Geluidsniveaumeter. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/6
For additional self-service support options and community forums, please visit: www.StarTech.com/support
Revision: August 2, 2024
Quick-Start Guide
Product ID
D130-DECIBEL-METER
Compact Decibel Meter - Range 30 to 130dB
Feature Function / Operation
1
Capacitive
Microphone with
Foam Wind-
Screen
• Captures Sound for Measurements
2LCD Display • Displays Settings and Measurement Information
3Power On/O
Button • Turns the Device On and O
4
Fast/Slow
Response Speed
Button
• Switches Between Fast and Slow Response Modes
5
Measuring Mode
(MAX/MIN)
Button
• Switches Between Maximum (MAX) and Minimum (MIN) Measuring
Modes
6Hold & Back-
Light Button
• Holds Readings within the Current Timing Interval
• Turns LCD Display Back-Light On and O
7Rear Battery
Compartment • Houses Installed Batteries
Package Contents
• Decibel Meter x 1
• AAA Batteries x 3
• Quick-Start Guide x 1
Requirements
For the latest manuals, product information, technical specications, and declarations of
conformance, please visit: www.StarTech.com/D130-DECIBEL-METER
• Phillips Head Screwdriver (for battery installation)
*Product may vary from image
1
2
43
5 6
7
Quick-Start Guide
Battery Installation
1. Using a (not included) remove the screw from the Phillips Head Screwdriver
bottom of the , and remove the cover.Battery Compartment
Note: If used batteries are installed, remove them.
2. Install the included 3x AAA Batteries into the , as shown Battery Compartment
in .Diagram 1
3. Replace the cover, then using a (not included) Phillips Head Screwdriver
drive the screw (removed in Step 1) back into the hole at the bottom of the
Battery Compartment.
Operation
Turning the Device on and o
To turn the device on: Power On/O ButtonLong press the for 2 seconds, while
the device is powered o.
To turn the device o: Short press the Power On/O Button, while the device is
powered on.
Diagram 1
Diagram 2
Element Function
ABattery Life
Indicator
• Displays at all times when the device is
powered on, indicating the battery usage
level
BMAX or MIN
Indicator
• Displays when the device is in MAX or
MIN Measuring Mode
C
Decibel
Measurement
Reading
• Displays at all times when the device
is powered on, indicating noise
measurement detected in decibels (dB)
D
FAST, SLOW
or HOLD Mode
Indicator
• Displays when the specic mode
is activated, indicating the timing
interval in which the dB measurement
is displayed and if the current values
displayed are held
EOut of Range Alert • Displays when the measurement is less
than 30dB or more than 130dB
B
A
C
D
MAX/MIN Modes
MAX & MIN Modes are optional operation modes of the . While in MAX or MIN Decibel Reader
Modes the on the will display the loudest (MAX), Decibel Measurement Reading LCD Display
or quietest (MIN) measurements captured while in that specic mode. The values will refresh if a
louder or quieter measurement is detected while in the specic mode.
To toggle between MAX, MIN and Standard Modes: Short press the
Measuring Mode (MAX/MIN) Button.
LCD Display, Settings and Measurement Information
Refer to Image ( ) and the table LCD Display Diagram 2 Element/Function
to understand the settings and measurement information shown on the LCD
Display.
Standard Mode
Standard Mode is the default operation mode of the . While in Standard Mode, Decibel Reader
the on the will display the current sound reading.Decibel Measurement Reading LCD Display
FAST/SLOW Response Speeds
While in standard mode, the current sound reading will refresh values at FAST (125ms) or
SLOW (1s ) intervals, based upon user selection and preference.
To toggle between FAST and SLOW response speeds: Short press the
FAST/SLOW Response Speed Button.
Hold Mode
Hold Mode is an optional operation mode of the . While in Hold Mode the Decibel Reader Decibel
Measurement Reading LCD Displayon the will continuously display the sound reading that was
on the display when Hold Mode was activated.
To toggle in and out of Hold Mode: Hold & Back-Light ButtonShort press the .
Turning the LCD Display Back-Light
To turn the LCD Display Back-Light on and o: Hold & Back-Light Button Long press the for 2
seconds, while the device is powered on..
Additional Features
Power Alert
The power sign will display when the battery is critically low, indicating it is time to change
batteries.
Auto-O
The device will automatically power down if it’s not interacted with for 5 minutes.
E
Product specificaties
| Merk: | StarTech.com |
| Categorie: | Geluidsniveaumeter |
| Model: | D130-DECIBEL-METER |
Heb je hulp nodig?
Als je hulp nodig hebt met StarTech.com D130-DECIBEL-METER stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Geluidsniveaumeter StarTech.com
8 November 2024
Handleiding Geluidsniveaumeter
- Geluidsniveaumeter Amprobe
- Geluidsniveaumeter Extech
- Geluidsniveaumeter Fluke
- Geluidsniveaumeter Laserliner
- Geluidsniveaumeter Monacor
- Geluidsniveaumeter PCE Instruments
- Geluidsniveaumeter Pyle
- Geluidsniveaumeter TFA
- Geluidsniveaumeter Trotec
- Geluidsniveaumeter Uni-T
- Geluidsniveaumeter Velleman
- Geluidsniveaumeter Voltcraft
- Geluidsniveaumeter Joy-it
- Geluidsniveaumeter Steren
- Geluidsniveaumeter Sauter
- Geluidsniveaumeter Testo
- Geluidsniveaumeter PeakTech
- Geluidsniveaumeter Chauvin Arnoux
Nieuwste handleidingen voor Geluidsniveaumeter
3 December 2024
17 November 2024
17 November 2024
15 November 2024
6 November 2024
22 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024