Speco Technologies VGA135 Handleiding

Speco Technologies Niet gecategoriseerd VGA135

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Speco Technologies VGA135 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
1
VGA135 VGA CAT5 Extender
Thank you for your purchase of the VGA135 VGA CAT5 extender. This VGA Extender allows VGA video signals to transmit up to
328’ (100m) via 4 pairs of CAT5 STP or UTP cable. The VGA135 can be used in a home or commercial application as a smart,
fast, and cost-effective alternative as it replaces costly and bulky VGA cable. VGA135 is ideal for classroom video distribution,
lecture halls, retail kiosks, video information displays, overhead projector systems, PC-training systems, and tradeshows.
FEATURES
β€’ Passive device, no power required.
β€’ Includes transmitter and receiver.
β€’ Resolution up to 1920x1080 pixels.
β€’ Up to 328’ (100m) via standard 4 pairs CAT5 STP or UTP cable
β€’ Replaces costly VGA cable with less expensive UTP cable.
β€’ Transmitter has built in virtual DDC to avoid improper settings of resolution and frequency.
β€’ Transmitter has built in sync mode selection for signal stability.
β€’ Receiver has built in sync filter level adjustment for signal stability.
UNIT VIEW
Transmitter
Receiver
INSTALLATION
2
TRANSMISSION DISTANCE CHART
RECOMMENDED CABLE
1. CAT5e UTP/STP or CAT6 UTP cable.
2. There are some monitor models with very high sync-sensitive demand. For these units, it’s recommended to use STP
(shielding twisted pair) cable instead of UTP (unshielded twisted pair).
RJ45 PINOUT
(PIN TIA/EIA-568B)
TIPS FOR USING STP CABLE
1. STP (shielding twisted pair) Cable.
2. STP (shielding) RJ45 connector with STP cable connection.
SYNC MODE SELECT SWITCH
← Mode 1
β†’ Mode 2
1. For β€œnewer” monitors, such as LCD monitors over 17”, it is recommended using Mode 1 for the best transmission
stability. If the picture is not normal, please switch to Mode 2.
2. For β€œolder” monitors, such as CRT or LCD monitors under 17”, it is recommended using Mode 2 and adjusting the Sync
Filter Level at the receiver. If the picture is not normal after following above suggestion, please change UTP to STP
(shielding twisted pair) cable.
Max. Distance via CAT5e Cable
800x600 pixels (60Hz) 328’ (100M)
1024x768 pixels (60Hz) 246’ (75M)
1280x1024 pixels (60Hz) 196’ (60M)
1920x1080 pixels(60Hz) 131’ (40M)
(PIN TIA/EIA-568B)
PIN Wire Color
1 Orange-white Red +
2 Orange Red -
3 Green-white H-Sync
4 Blue Green +
5 Blue-white Green -
6 Green V-Sync
7 Brown-white Blue +
8 Brown Blue -
3
SYNC FILTER LEVEL SETTING
DIP Switch Chart
DIP Switch
1
2
3
4
5
Level 0 (Min) ↓ ↓ ↓ ↓ ↓
Level 1
↓
Level 2 ↓ ↑ ↓ ↓ ↓
Level 3
↓
Level 4 ↓ ↓ ↓ ↑ ↓
Level 5
(Max
)
↑
Sync Filter Level is designed for improving signal synchronizing stability, not for picture quality or skewing problems when
using UTP cable.
There is no definitive setting as monitors have different set values. Please try multiple levels of setting to figure out the best
stability.
If there is no picture display or picture is not stable after adjustment, please change the UTP to STP cable.
CAUTION
1. The wiring must be kept away from electromagnetic equipment, i.e. microwave, wireless, hi-voltage cables,
etc.
2. The maximum distances supported by the VGA Extender are dependent on the type of twisted pair cable
and image resolution of the PC’s VGA interface. Make sure that the maximum recommended operational
distances have not been exceeded.
3. All wiring is β€œstraight-through” twisted pair cable, and not to be used for other LAN or telephone equipment.
4. Do not connect the VGA Extender to a telecommunication outlet wired to unrelated equipment.
TROUBLESHOOTING
1. No picture display:
 Check Link cable.
 Check DIP switch setting.
 Check VGA cable connection.
 Change the resolution or frequency.
 Change UTP to STP cable.
2. Picture not stable or disappearing intermittently:
 Check DIP switch setting.
 Change the resolution or frequency.
 Move cable away from electromagnetic equipment.
 Change UTP to STP cable.
3. Picture tilt:
 Check DIP switch setting.
 Change the resolution or frequency.
 Change UTP to STP cable.

Product specificaties

Merk: Speco Technologies
Categorie: Niet gecategoriseerd
Model: VGA135

Heb je hulp nodig?

Als je hulp nodig hebt met Speco Technologies VGA135 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Speco Technologies

Speco Technologies

Speco Technologies APCR620L Handleiding

18 September 2024
Speco Technologies

Speco Technologies V5T3 Handleiding

18 September 2024
Speco Technologies

Speco Technologies V5T3M Handleiding

18 September 2024
Speco Technologies

Speco Technologies V5B3M Handleiding

18 September 2024
Speco Technologies

Speco Technologies APCR640L Handleiding

26 Augustus 2024
Speco Technologies

Speco Technologies O4BXLP1M Handleiding

26 Juli 2024
Speco Technologies

Speco Technologies O8TDD2M Handleiding

25 Juli 2024
Speco Technologies

Speco Technologies SXA400 Handleiding

25 Juni 2024
Speco Technologies

Speco Technologies SXU24V Handleiding

25 Juni 2024
Speco Technologies

Speco Technologies ZIPK16N1 Handleiding

25 Juni 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx

Gourmetmaxx 03863 Handleiding

24 December 2024
Vello

Vello PGS-P Handleiding

24 December 2024
Venom

Venom Quad Charging Station VS4796 Handleiding

24 December 2024
Nec

Nec IPJ2000CM Handleiding

24 December 2024
Monogram

Monogram ZKPN Handleiding

24 December 2024
Philips

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024
Philips

Philips Senseo HD7002 Handleiding

24 December 2024
D-Link

D-Link DUB-C2 Handleiding

24 December 2024
Nec

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024
Nec

Nec DS1-TM01 Handleiding

24 December 2024