Sony RDP-M15iP Handleiding

Sony Speaker RDP-M15iP

Lees hieronder de 📖 handleiding in het Nederlandse voor Sony RDP-M15iP (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Disposal of Old Electrical &

Electronic Equipment (Applicable

in the European Union and other

European countries with separate

collection systems)

This symbol on the product or on its packaging

indicates that this product shall not be treated as

household waste. Instead it shall be handed over

to the applicable collection point for the recycling

of electrical and electronic equipment. By

ensuring this product is disposed of correctly, you

will help prevent potential negative consequences

for the environment and human health, which

could otherwise be caused by inappropriate waste

handling of this product. The recycling of

materials will help to conserve natural resources.

For more detailed information about recycling of

this product, please contact your local Civic

Office, your household waste disposal service or

the shop where you purchased the product.

Applicable accessory: Remote Commander.

Disposal of waste batteries

(applicable in the European

Union and other European

countries with separate

collection systems)

This symbol on the battery or on the packaging

indicates that the battery provided with this

product shall not be treated as household waste.

On certain batteries this symbol might be used in

combination with a chemical symbol. The

chemical symbols for mercury (Hg) or lead (Pb)

are added if the battery contains more than

0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of

correctly, you will help prevent potentially

negative consequences for the environment and

human health which could otherwise be caused

by inappropriate waste handling of the battery.

The recycling of the materials will help to

conserve natural resources.

In case of products that for safety, performance or

data integrity reasons require a permanent

connection with an incorporated battery, this

battery should be replaced by qualified service

staff only.

To ensure that the battery will be treated properly,

hand over the product at end-of-life to the

applicable collection point for the recycling of

electrical and electronic equipment.

For all other batteries, please view the section on

how to remove the battery from the product

safely. Hand the battery over to the applicable

collection point for the recycling of waste

batteries.

For more detailed information about recycling of

this product or battery, please contact your local

Civic Office, your household waste disposal

service or the shop where you purchased the

product.

If you have any questions or problems concerning

your unit, please consult your nearest Sony dealer.

Precautions



To disconnect the AC adaptor, pull it out by the

plug, not the cord.



Since a strong magnet is used for the speaker,

keep credit cards using magnetic coding or

spring-wound watches, CRT-based TVs, or

projectors, etc., away from the unit to prevent

possible damage from the magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive dust,

mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit on

a surface (a rug, a blanket, etc.) or near

materials (a curtain) which might block the

ventilation holes.



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



Do not handle the unit with wet hands.



Do not place the unit anywhere near water.

NOTES ON LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

Note



In this Reference Guide, “iPod” is used as a

general reference to functions on an iPod or

iPhone, unless otherwise specified by the text

or illustrations.

WARNING

To reduce the risk of fire or electric

shock, do not expose this apparatus to

rain or moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place lighted

candles on the apparatus.

To reduce the risk of fire or electric shock, do not

expose this apparatus to dripping or splashing,

and do not place objects filled with liquids, such

as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug of AC adaptor is used to

disconnect the AC adaptor from the mains,

connect it to an easily accessible AC outlet.

Should you notice an abnormality in it,

disconnect it from the AC outlet immediately.

The unit is not disconnected from the AC power

source (mains) as long as it is connected to the

wall outlet, even if the unit itself has been turned

off.

The nameplate and important information

concerning safety are located on the bottom

exterior of the main unit and on the surface of the

AC adaptor.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

Notice for customers: the following

information is only applicable to equipment

sold in countries applying EU directives

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan, Minato-ku, Tokyo,

108-0075 Japan. The Authorized Representative

for EMC and product safety is Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,

Germany. For any service or guarantee matters,

please refer to the addresses given in separate

service or guarantee documents.

4-274-302- (1)73

Personal Audio Docking System

RDP-M15iP

Printed in China

Reference Guide

Others

Troubleshooting

General

The power does not turn on when the AC

adaptor is connected.



Make sure the AC adaptor is connected to the wall outlet

firmly.

The power does not turn on when the AC

adaptor is disconnected, or the button  /

indicator flashes several times and then the

power of the unit turns off.



The rechargeable battery may be depleted. In this case,

connect to the AC adaptor to charge the battery. (See “To

prepare a power source.”)

The rechargeable battery is depleted.



Connect to the AC adaptor to charge the battery.

There is no audio.



Adjust VOLUME +/− VOL +/− ( on the remote

commander).

Noise is heard.



Ensure that the unit is not in the vicinity of in-use

portable phones, etc.

The two different music sources are mixed

together during playback.



Stop playback of your iPod or external component.

The BATTERY/CHARGE indicator (red)

flashes.



The rechargeable battery is not connected properly, or

cannot be charged for some reason. Check that the

battery connector is connected firmly; otherwise, replace

the battery.

iPod

There is no audio.



Make sure the iPod is connected firmly.

Operation is not performed.



Make sure the iPod is connected firmly.

The iPod does not charge.



Make sure the iPod is connected firmly.



Make sure the AC adaptor is connected firmly.

Audio-in

There is no audio.



Make sure the audio connecting cable is connected

firmly.

The sound is low.



Confirm the volume of the connected external

component.

Remote commander

The remote commander does not function.



Replace the battery in the remote commander with a

new one if it is weak.



Make sure that you are pointing the remote commander

at the remote sensor on the unit.



Remove any obstacles in the path of the remote

commander and the unit.



Make sure the remote sensor is not exposed to strong

light such as direct sunlight or fluorescent lamp light.



Move closer to the unit when using the remote

commander.

If the problem persists, consult your nearest Sony dealer.

Specifications

Section for iPod

DC out: 5 V

MAX: 1 A

General

Speaker

Approx. 5.0 cm dia. 8 Ω

Input

AUDIO IN jack (ø 3.5 mm stereo minijack)

Power output

10 W + 10 W (at 10% harmonic distortion)

(with AC adaptor)

2 W + 2 W (at 10% harmonic distortion)

(with rechargeable battery)

Power requirements

Rechargeable battery pack: NH - M15 RDP

Battery life

See “Battery Life” of “Power source” for details.

External power source

DC IN 14.5V

Dimensions

Approx. 337.0 mm × 108.2 mm × 77.0 mm (w/h/d)

(not including projecting parts and controls)

Mass

Approx. 1.1 kg

Supplied accessories

Remote commander (1)

AC adaptor (1)

Dock Holder A/B/C/D/E/F (6)

Carrying pouch (1)

Design and specifications are subject to change

without notice.

Operations

Power source

Power management system

After playback of the iPod (or component

connected to AUDIO IN jack) has finished, if no

operation is performed for about 20 minutes, the

unit will automatically turn off.

To prepare a power source

This unit contains a rechargeable battery pack.

Charge the battery before using this unit for the

first time, or when it is depleted. You can operate

the unit while charging.

1 Connect the supplied AC adaptor to the

DC IN 14.5V jack on the back of this

unit firmly, and plug it into a wall outlet

to charge the battery.

Note on the AC adaptor



Use the supplied Sony AC adaptor only. The

polarity of the plugs of other manufacturers

may be different. Failure to use the supplied AC

adaptor may cause the unit to malfunction.

2 Confirm that charging has started.

The BATTERY/CHARGE indicator (red) lights

up while charging, and turns off when

charging is complete.

Note



It will take approximately 5 hours to charge the

battery.

To use the rechargeable

battery

You can operate the unit with the rechargeable

battery instead of the AC adaptor.

Battery Life

(Approx. hours) (JEITA*)

When Usage time

Playback of iPod 6

* Measured by JEITA (Japan Electronics and

Information Technology Industries

Association) standards. The usage time is

measured with the SOUND function set to off,

and actual battery life will vary depending on

the circumstances of the unit.

Notes on the rechargeable battery



The maximum output will be lower when the

AC adaptor is disconnected.



The BATTERY/CHARGE indicator (green)

becomes dim when the battery is weak, and

turns off when remaining battery power is

depleted.

When to replace the rechargeable

battery

Repeated recharging causes the capacity of the

battery power to decrease over time. Replace the

battery pack when its capacity becomes half the

usual time, even after charging it fully.

Note



The rechargeable battery pack is not a

commercially available product. To purchase

rechargeable battery pack (NH – M15 RDP),

consult with your nearest Sony dealer.

To replace the rechargeable

battery

1 Remove the screw of the battery

compartment at the bottom of the unit,

and open the lid.

2 Disconnect the connector of the battery

pack and pull the old one out.

3 Insert a new battery pack and connect its

connector to the jack.

4 Replace the battery compartment lid and

tighten the screw.

Notes



Charge a new battery pack before use. See “To

prepare a power source” for details.



Turn off the unit and disconnect the AC

adaptor before replacing the battery pack.



When replacing the battery pack, place a soft

cloth etc., under the unit.

To charge your iPod (AC only)

You can use the unit as a battery charger for your

iPod when the power is supplied by the AC

adaptor.

Charging begins when the iPod is connected to

the unit. The charging status appears in the

display on iPod. For details, see the user’s guide of

your iPod.

To turn the unit on/off

Press / (power).

The / button indicator will light up when the

unit is turned on.

Remote commander

Before using the supplied remote commander for

the first time, remove the insulation film.

Aim the remote commander at the (Remote

sensor) of the unit.

The / button indicator flashes when the remote  

commander’s command is received.

VOL + and  buttons have a tactile dot.

 / (Power)*



Turns the unit on/off. The / button indicator

lights up when the unit is turned on.

 (Play/Pause)



Start playing iPod. Press again to pause/resume

playback.



Press and hold to turn off the iPod.

 (Forward)



Go to the next track.



Press and hold while listening to the sound to

locate a desired point.



Press and hold in pause while observing the

display on iPod to locate a desired point.

 (Backward)



Go back to the previous track. During

playback, this operation returns to the

beginning of the current track. To go back to

the previous track, press twice.



Press and hold while listening to the sound to

locate a desired point.



Press and hold in pause while observing the

display on iPod to locate a desired point.

 (Up)/ (Down)



Select a menu item or track for playback.



Go back to the previous menu.



Press and hold to go back to the main menu.

ENTER



Execute the selected menu item or begin

playback.

SOUND



Press once or twice to obtain the desired sound

effect. (For details, see “To obtain the bass or

expansion sound effect.”)

VOL +/ −(Volume plus/minus)



Adjust the volume.

* 

When using the rechargeable battery, press the

/ button on the unit. The / button of the

remote commander works only when the AC

adaptor is used.

Notes



Some operations may differ or may not be

available between models of iPod.



Some operations may differ or may not be

available when using the iPod in a horizontal

position.

When to replace the battery

With normal use, the battery (CR2025) should

last for about 6 months. When the remote

commander no longer operates the unit, replace

the battery with a new one.

the side facing up

Note



If you are not going to use the remote

commander for a long time, remove the battery

to avoid any damage that may be caused by

leakage and corrosion.

Operating an iPod

Compatible iPod/iPhone

models

The compatible iPod/iPhone models are as

follows.

Update software of your iPod/iPhone to the latest

version before using it with this unit.

iPod touch (4th generation)

iPod touch (3rd generation)

iPod touch (2nd generation)

iPod touch (1st generation)

iPod nano (6th generation)*

iPod nano (5th generation)

iPod nano (4th generation)

iPod nano (3rd generation)

iPod nano (2nd generation)

iPod with video

iPod classic

iPhone 4S

iPhone 4

iPhone 3GS

iPhone 3G

iPhone

* The iPod nano (6th generation) cannot be

controlled by the remote when the command of

“ ,” “ ,” “ ,” and “ ” is pressed.MENU   ENTER

On copyrights

iPhone, iPod, iPod classic, iPod nano, and iPod

touch are trademarks of Apple Inc., registered in

the U.S. and other countries.

“Made for iPod,” and “Made for iPhone” mean

that an electronic accessory has been designed to

connect specifically to iPod or iPhone,

respectively, and has been certified by the

developer to meet Apple performance standards.

Apple is not responsible for the operation of this

device or its compliance with safety and

regulatory standards. Please note that the use of

this accessory with iPod or iPhone may affect

wireless performance.

Note



This unit is not specified for use with an iPad,

and malfunction may result if used as such.

To set an iPod on the Docking

Tray

1 Press on the front of the unit until PUSH

the Docking Tray comes forward.

2 Set your iPod on the Dock connector.

To set an iPod in sideways

You can use the supplied Dock Holder to set your

iPod. The Dock Holder code (A, B, etc.) and

compatible iPod model(s) are indicated on the

Dock Holder. Check for compatibility before use.

Example

Dock Holder

code

Compatible iPod models

A iPod touch (4th generation)

iPod touch (3rd generation)/

iPod touch (2nd generation)/

iPod touch (1st generation)

C iPod nano (5th generation)

D iPod nano (4th generation)

E iPhone 4S/iPhone 4

F iPhone 3GS/iPhone 3G/

iPhone

1 Press on the front of the unit until PUSH

the Docking Tray comes forward.

2 Attach and slide the appropriate Dock

Holder down in the Docking Tray.

Hold the Docking Tray when attaching the

Dock Holder.

3 Set your iPod on the Dock connector.

4 Twist the Docking Tray anti-clockwise to

the horizontal position.

Conversely, the Docking Tray will not move

when twisted clockwise.

Notes



To change the Dock Holder, slide it up and pull

out. Hold the Docking Tray when pulling the

Dock Holder out.



Attach the Dock Holder for using the iPod in

the horizontal position. Otherwise, the iPod

may fall when the Docking Tray is twisted.

To close the Docking Tray

1 Twist the Docking Tray clockwise until it

is in vertical position.

2 Remove the iPod from the Dock

connector.

3 Press on the front of the unit until PUSH

the Docking Tray is locked.

To operate

Press .

When using the rechargeable battery with the

remote commander, press / on the unit, and

then press .

The iPod begins to play back.

You can operate the connected iPod via this unit

or the iPod itself.

Notes



Remove the case or cover from your iPod

before setting it in the Docking Tray to ensure a

stable connection.



When placing or removing the iPod, hold the

iPod at the same angle as that of the connector

on this unit, and do not twist or bend the iPod

as it may result in connector damage.



Remove the iPod and lock the Docking Tray of

the unit when transporting it, otherwise a

malfunction may result.



When placing or removing the iPod, hold the

Docking Tray securely.



If the battery of your iPod is extremely low,

charge it for a while before operation.



An iPod touch/iPhone will not work unless it is

turned on. Be sure to turn on the power of the

iPod touch/iPhone before operation.



Sony cannot accept responsibility in the event

that data recorded to an iPod is lost or damaged

when using an iPod connected to this unit.



For details of environmental conditions for

operating your iPod, check the website of Apple

Inc.

To adjust the volume

Press VOLUME +/− VOL +/− ( on the remote

commander).

Tip



The / button indicator flashes three times

when the sound is set to either maximum or

minimum volume.

To obtain the bass or

expansion sound effect

Press .SOUND

The button indicator lights up umber. SOUND

High quality bass sound will be heard.

Press the button again.

The indicator lights up green. Additional

expansion of the sound field will be heard.

To return to normal sound, press the button again

and the indicator will turn off.

Connecting optional

components

You can enjoy the sound from an optional

component, such as a portable digital music

player, through the speakers of this unit. Be sure

to turn off the power of each component before

making any connections.

1 Firmly connect the line output jack of a

portable digital music player (or other

component) to the AUDIO IN jack on the

back of the unit, using a suitable audio

connecting cable (not supplied).

2 Press to turn on the unit.

3 Turn the connected component on.

4 Play the connected component.

The sound from the connected component is

output from the speakers of this unit.

Notes



The audio connecting cable required depends

on the external equipment. Make sure the cable

is correct for the external equipment to be

connected.



If the volume level is low, adjust the volume of

the unit first. If the volume is still too low,

adjust the volume of the connected equipment.



When playing an external component

connected to the AUDIO IN jack, stop playback

of your iPod.



Disconnect the audio connecting cable when

audio-in is not in use.

About App

Dedicated Dock App for iPod/iPhone available at

Apple App Store.

Search for “D-Sappli” and download the free App

to find out more about the functions.

Notes



If the App to link with this unit is not

downloaded to your iPod/iPhone, a pop-up

message prompting you to download D-Sappli

may appear repeatedly.

Deactivate the App’s link function to stop the

pop-up message.



To deactivate the App’s link function: Connect

the AC adaptor, and then press / to turn off

the unit. Remove your iPod/iPhone from the

Dock connector, and then press and hold

VOLUME − and  simultaneously for more

than 2 seconds. (The BATTERY/CHARGE

indicator (red) flashes 3 times when

deactivated.)



Repeat the above steps to activate the function.

(The BATTERY/CHARGE indicator (green)

flashes 3 times when activated.)

VOLUME + and  buttons have a tactile dot.

BATTERY/CHARGE

SOUND

Docking Tray

iPod & iPhone



− VOLUME +

/

PUSH

Remote

sensor

Product specificaties

Merk:	Sony
Categorie:	Speaker
Model:	RDP-M15iP
Kleur van het product:	Zwart
Gewicht:	1100 g
Bluetooth:	Nee
Gemiddeld vermogen:	20 W
Volumeregeling:	Digitaal
FM-radio:	Nee
Equalizer-instellingen:	Nee
Audio-uitgangskanalen:	2.0 kanalen
Diameter driver:	50 mm
Frequentiebereik:	- Hz
Afmetingen (B x D x H):	337 x 77 x 108.2 mm
Apple docking-compatibiliteit:	iPhone, iPod
Ingebouwde lader:	Ja
AC-ingangsspanning:	100 - 240 V