Sony PCWA-AR800 Handleiding

Sony Overige computer accessoire PCWA-AR800

Lees hieronder de đź“– handleiding in het Nederlandse voor Sony PCWA-AR800 (2 pagina's) in de categorie Overige computer accessoire. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
PCWA-AR800
©2004 Sony Corporation Printed in Japan
4-680-222- (1)11
Wireless
Broadband Router
Troubleshooting Guide
This document provides solutions to common problems
encountered with the Broadband Router.Wireless
Please refer to this guide before contacting Sony
Customer Information Services.
The PCWA-AR800 consists of:
• Broadband Router Unit PCWA-R1
• Wireless LAN Access Point PCWA-A820
In this document, we refer to the Broadband Router Unit as the
Router Unit and to the Wireless LAN Access Point as the Access
Point.
The PCWA-AR800 can be used at frequency settings of 2.4 GHz
and 5 GHz. Change this setting as necessary. (By default, the
PCWA-AR800 is set to 2.4 GHz.)
Preparations
Case 1 No communication between the computer and
Wireless Broadband Router
1Are you attempting to establish a connection at a frequency
of 5 GHz?
The default wireless broadband frequency setting is 2.4 GHz. If you want to establish a wireless
connection at 5 GHz, access the Access Point Setup page through a wired network, and change
the frequency setting to 5 GHz (802.11a). Refer to the separate Quick Start Guide for details about
how to display the Access Point Setup page.
2Was your computer properly configured for wireless
communication?
When using the Access Point functions under factory default settings, configure the computer as
follows.
The factory default settings of the Access Point function are:
• Network Name (SSID):
The 6-character identifier printed on the label inside the rear cover of the Wireless Unit
z Hint
For details about the location of the network name (SSID), refer to procedure 3 of the Quick Start Guide.
• Security settings
Encryption (WEP): Disabled
• IEEE 802.11 Mode: 11g, 11b (High multicast rate)
With the Windows Me and Windows 2000 operating systems, perform setup as described in the
documentation provided with your Wireless LAN PC Card.
With the Windows XP operating system, proceed as follows.
1
Click “Start”, and then click “Control Panel”.
2
In “Control Panel”, click “Network and Internet Connections”, and then click
“Network Connections”.
z Hint
If “Network and Internet Connections” does not appear, click “Switch to Category View” on the left.
3
In the “Network Connections” window, right-click the icon of the wireless network to
which you want to connect, and click “View Available Wireless Networks”.
4
In the “Connect to Wireless Network” dialog box (with Windows XP SP1, the
“Wireless Network Connection” dialog box), select the Access Point from “Available
Wireless Networks”, and click “Connect”. (When using the Access Point functions
under factory default settings, check the 6-character identifier printed on the label
inside the rear cover of the Wireless Unit.)
3Are the network name (SSID) and security settings configured
correctly?
To connect to the Access Point, the network name (SSID) and security settings must be the same
at the computer and the Access Point.
z Hint
When using the Access Point functions under factory default settings, use the settings listed in above.2
With the Windows Me and Windows 2000 operating systems, verify the Access Point network name (SSID)
and security settings of the wireless LAN PC card as described in its documentation.
With the Windows XP operating system, proceed as follows to verify the settings.
1
Open the “Connect to Wireless Network” dialog box (with Windows XP SP1, the
“Wireless Network connecion” dialog box) as described in 2 above.
2
Select the network name (SSID) of the Access Point from “Available Wireless
Networks”.
3
Make sure that the security settings of the Access Point match those of the
computer.
4
Click “Connect”.
If the connection is not established, reset the Access Point functions to the factory default
settings as described in “Miscellaneous”, “Case 1: Forgot settings”, and then set up the
Access Point functions again as described in the separate Quick Start Guide.
Continued on next page
4Can the IP address of the computer be acquired?
With the computer setting “Obtain an IP address automatically” enabled, perform the following
steps. For information on how to set the IP address of the computer, see Windows Help.
Windows Me operating system
1
Click “Start”, and click “Run”.
2
In the dialog box used to specify the file name, enter “winipcfg” (exclude the
quotation marks) and click “OK”.
3
From the list in the “IP Setup” dialog box, select the Wireless LAN interface that you
are using (PC card, computer internal wireless LAN, etc.).
4
Make sure that an IP address is shown in the “IP address” text box.
5
If the IP address is “0.0.0.0” or an address starting with “169.254.” is displayed, click
“Release”, and then “Renew”.
Note
If an IP address starting with “169.254.” is displayed, a suitable IP address was not obtained with
“Obtain an IP address automatically” and your Windows operating system assigned an address to the
wireless LAN PC card or Wireless LAN Converter. In this condition, correct network connection is not
possible. Perform the setup again as described in the separate Quick Start Guide.
Windows 2000 and Windows XP operating systems
1
Click “Start”, point to “Programs” (“All Programs” when using the Windows XP
operating system) and then “Accessories”, and click “Command Prompt”.
2
In the command prompt window, enter “ipconfig /all” (exclude the quotation marks)
and press the Enter key.
3
Verify the IP address setting information of the Wireless LAN interface that you are
using (PC card, computer internal wireless LAN, etc.).
z Hint
The “Description” field shows the name of the Wireless LAN interface.
4
If the IP address is “0.0.0.0” or an address starting with “169.254.” is displayed,
enter “ipconfig /renew” (exclude the quotation marks) and press the Enter key.
A new IP address is assigned.
Note
If an IP address starting with “169.254.” is displayed, a suitable IP address was not obtained with
“Obtain an IP address automatically” and your Windows operating system assigned an address to the
wireless LAN PC card or Wireless LAN Converter. In this condition, correct network connection is not
possible. Perform the setup again as described in the separate Quick Start Guide.
Connections
Case 1 Cannot display the Setup Page (an error message
appears)
If entering “http://192.168.11.1/” in the address field of the Web browser does not open the Setup Page,
check the following.
1Can the IP address of the computer be acquired?
See “Preparations”, “Case 1: No communication between the computer and Wireless Broadband
Router”, item 4.
2Are the Access Point and Router Unit power connections
correct?
When powered properly, the Status indicator of the Router Unit is lit and the Status indicator of
the Access Point is flashing slowly.
3Is the AC adapter power switch on?
Make sure that the AC adapter is properly connected and verify that the power switch is on.
z Hint
When the AC adapter power switch is on, the LED on the adapter is lit.
4Is the Ethernet cable correctly connected?
Make sure that an end of the Ethernet cable is connected to a LAN connector of the Router Unit.
Connect the other end of the Ethernet cable to your computer.
z Hint
The Ethernet port of your computer is on its back panel.
5Is the Windows XP “Internet Connection Firewall” function
enabled?
If the “Internet Connection Firewall” function is enabled, communication may not be possible.
See “Miscellaneous”, “Case 4: Computer firewall function and browser proxy settings” for details.
6Is the Web browser of the computer used for the Wireless
Broadband Router setup configured to use a proxy server?
Make sure that there are no proxy settings enabled for the IP address of the Wireless Broadband
Router. See “Miscellaneous”, “Case 4: Computer firewall function and browser proxy settings”
for details.
Power switch
a: Off
? : On
Cable modem or DSL modem
LED
• Sony, VAIO, , , and the Eco Info logo are trademarks of Sony Corporation.
• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other
countries.
• In this document, Microsoft® Windows® Millennium Edition is referred to as Windows Me, Microsoft
® Windows®
2000 Professional is referred to as Windows 2000, Microsoft
® Windows® XP Home Edition and Microsoft®
Windows® XP Professional are referred to as Windows XP.
• Netscape is a registered trademark of Netscape Communications Corporation.
• All other names of systems, products and services are trademarks of their respective owners.
• In the document, the ™ or ® marks are not specified.
Contents
Preparations
• No communication between the computer and
Wireless Broadband Router ........................................................................ Case 1
Connections
• Cannot display the Setup Page (an error message appears) ..................... Case 1
Router Functions
• The Internet Gateway is shown as a network connection.
What does this mean? ................................................................................ Case 1
• Cannot connect to the Internet .................................................................... Case 2
• I changed the LAN settings of the Router Unit, but I can no longer
connect to the Router Unit or network ........................................................ Case 3
Access Point Functions
• Clicked the “Refresh” button under “Access Point List”, but nothing
appears in the list ........................................................................................ Case 1
• Several Access Points are listed, but I do not know which one to select .... Case 2
• The user name and password input dialog box appears despite
the lack of settings ...................................................................................... Case 3
• Unable to connect after Access Point functions settings are made ............ Case 4
• If “Easy Setup” is used after “Advanced Setup”,
what about items not included in “Easy Setup”? ......................................... Case 5
Miscellaneous
• Forgot settings ............................................................................................ Case 1
• The power cord is plugged to the AC outlet, but the indicators
do not light .................................................................................................. Case 2
• After pressing the Quick Setup switch, the Status indicator
starts flashing red ........................................................................................ Case 3
• Computer firewall function and browser proxy settings .............................. Case 4
To power outlet
Printed on 100% recycled paper using VOC (Volatile Organic Compound)-free vegetable oil
based ink.
Router Functions
Case 1 The Internet Gateway is shown as a network
connection. What does this mean?
It means that the Router Unit is recognized as the Internet Gateway. If you disconnect the Router Unit
from the network, the indication disappears.
Case 2 Cannot connect to the Internet
Are the WAN settings correct?
Select from the following depending on the connection method specified by your Internet service
provider.
• When connecting by DHCP (having an IP address assigned to the computer automatically), select
“Obtain an IP address automatically”. In this case, please confirm the DHCP client ID (in cases
where it is particularly specified).
• When connecting by a fixed IP address (manually assigning the computer IP address), select “Use the
following IP address”. In this case, enter the IP address for your computer specified by your Internet
service provider.
Refer to the separate Quick Start Guide for details.
Case 3 I changed the LAN settings of the Router Unit, but
I can no longer connect to the Router Unit or
network
See “Case 1: No communication between the computer and Wireless Broadband Router”, item 4 to
release and renew the IP address of your computer so that it matches the LAN settings of the Router
Unit. Alternately, you can restart the Router Unit, which automatically releases and renews the IP
address of your computer.
Note
In “Case 1: No communication between the computer and Wireless Broadband Router”, item , we recommend4
that you release and renew the IP address only when it is “0.0.0.0” or it starts with “169.254”. In the case above, you
must release and renew the IP address, regardless of the displayed address.
Access Point Functions
Case 1 Clicked the “Refresh” button under “Access Point
List”, but nothing appears in the list
1Did you wait long enough?
The scanning process may take some time. After clicking “Refresh”, wait at least 30 seconds
before checking the results.
2Can the IP address of the computer be acquired?
See “Preparations”, “Case 1: No communication between the computer and Wireless Broadband
Router”, item 4.
3Is the Access Point connected correctly to the Router Unit?
Make sure that connections are as shown.
4Is the Windows XP “Internet Connection Firewall” function
enabled?
See “Miscellaneous”, “Case 4: Computer firewall function and browser proxy settings” for details.
Case 2 Several Access Points are listed, but I do not
know which one to select
The “Access Point List” shows the MAC addresses of all the Access Points found.
Use the MAC address to identify the Access Point.
Check the MAC address of the Access Point to which you want to connect. The MAC address is
located on the label inside the rear cover of the Wireless Unit.
Case 3 The user name and password input dialog box
appears despite the lack of settings
Enter “admin” in the “User name” text box, and then click “OK”. Do not enter anything in the
“Password” text box.
Case 4 Unable to connect after Access Point functions
settings are made
Did you change the wireless connection settings of the computer
to match the Access Point functions settings?
If the network name (SSID) and security settings of the Access Point are changed, the wireless
connection settings of the computer must be changed accordingly. For information on how to do this,
refer to the documentation of the wireless LAN PC card or the Wireless LAN Converter.
Case 5 If “Easy Setup” is used after “Advanced Setup”,
what about items not included in “Easy Setup”?
If you reconfigure the unit with “Easy Setup” after using “Advanced Setup”, the items not included in
“Easy Setup” are set as follows.
Item Setting
Frequency (Channel) 2.4 GHz (Auto Select)
Broadcast Network Name (SSID) Yes
IEEE 802.11 Mode 11g, 11b (High multicast rate)
Super A/G Disable
Turbo Mode Disable
Access Control Accept all
Connection Method Obtain IP address automatically (DHCP)
Speed Auto-Detect
Setup Switch Enable
The Super A/G and Turbo Mode functions of the PCWA-AR800 are supported by the Wireless
LAN Converter PCWA-DE80 and Wireless LAN PC Card PCWA-C800S. Compatibility of the
Super A/G and Turbo Mode functions with third party Wireless Client devices is not guaranteed.
Cable modem or
DSL modem
Miscellaneous
Case 1 Forgot settings
Reset the Access Point and/or Router Unit, as described below.
To perform a reset, the Wireless Broadband Router must be on. It is possible to reset both units or only
the unit for which you have forgotten the settings. When you forget the Access Point settings, press the
Reset switch on the Wireless Unit. When you forget the Router Unit settings, press the Reset switch on
the Router Unit. Hold the switch for at least a second, and then release it.
The Wireless Broadband Router restarts automatically, and the settings of the unit whose Reset switch
is pressed revert to their factory defaults. Repeat the setup procedure.
Wireless Unit Router Unit
Note
When resetting the Access Point, be careful not to press the Quick Setup switch by mistake.
Case 2 The power cord is plugged to the AC outlet, but
the indicators do not light
1Is the AC adapter power switch on?
zHint
When the AC adapter power switch is on, the LED on the adapter is lit.
2Is the “Status Indicator” setting of the Access Point set to
Off?
Open the Setup Page of the Access Point, go to the Access Point “Management” page, and set
“Status Indicator” to On.
1
Click “Status Indicator” and “Change”.
2
Select “On” from the list and click “Execute Setup”.
3
When the completion message appears, click “Close”.
Reset switch
Quick Setup switch
Reset switch
To power outlet
Case 3 After pressing the Quick Setup switch, the Status
indicator starts flashing red
If the Quick Setup switch is held down for more than one second, the Status indicator starts to flash red.
30 seconds later, the Status indicator begins flashing slowly white to indicate normal operaton.
Note
The Quick Setup switch is used in setting the separately available Wireless LAN Converter PCWA-DE80 or
PCWA-DE30.
For information on how to use the Quick Setup switch, refer to Wireless LAN Converter PCWA-DE80
or PCWA-DE30 Quick Start Guide.
Case 4 Computer firewall function and browser proxy
settings
■The “Internet Connection Firewall” function is enabled
When the Windows XP “Internet Connection Firewall” function is enabled, it may prevent the
computer from being accessed externally (this function is disabled by default). This function can
prevent connection to your network when you change your Wireless LAN Converter or Access
Point settings. If this happens, disable the “Internet Connection Firewall” function as described
here, connect to the network, and then re-enable the function.
1Click “Start”, and then click “Control Panel”.
2In “Control Panel”, click “Network and Internet Connections”, and then click “Network
Connections”.
zHint
If “Network and Internet Connections” does not appear, click “Switch to Category View” on the left.
3In the “Network Connections” window, right-click the icon of the wireless network that
you want to use, and click “Properties”.
4Click the “Advanced” tab and (if selected) clear the “Protect my computer and network
by limiting or preventing access to this computer from the Internet” check box.
5Click “OK”.
Refer to Windows XP Help for details about the “Internet Connection Firewall” function.
Note
Make sure that you take appropriate security measures when the “Internet Connection Firewall” function is
disabled. Except when configuring the Access Point, it is strongly recommended that you enable the “Internet
Connection Firewall” function at all times.
â– When using a personal firewall software provided standalone
or as part of an antivirus or network security software
Antivirus scanning and network security software sometimes includes a function called a
“personal firewall”, intended to prevent unauthorized access by other computers. Depending on
the software, the security level of this function may initially be set to a high level. If this high
security level setting is left enabled, other computers may be unable to access your computer. This
can cause problems such as not being able to connect to the network when changing the Wireless
LAN Converter or Access Point settings. In this event, lower the security level to allow the
network connection. Refer to the software instructions or Help for details.
Notes
• Make sure that you take appropriate security measures.
• For questions about firewall functions, contact your firewall software manufacturer.
â– Proxy settings
Make sure that no proxy settings are enabled for the IP address of the Wireless Broadband Router.
Note
While the proxy server settings are disabled, it may not be possible to display other pages except the Wireless
Broadband Router Setup page.
Example 1: Using Microsoft Internet Explorer
1On the “Tools” menu, click “Internet Options”.
The “Internet Options” dialog box appears.
2On the “Connection” tab, click “LAN Settings”.
The “Local Area Network (LAN) Settings” dialog box appears.
zHint
If there are dial-up profiles in the “Dial-up” box, make sure that you select the “Never dial a connection”
check box.
3If the “Use a proxy server for your LAN (These settings do not apply to dial-up or VPN
connections)” check box is selected, clear the check box and click “OK”.
4When the Wireless Broadband Router setup is complete, return the proxy setting to
its original condition.
Example 2: Using Netscape
1Start the Web browser on the computer used for the Wireless Broadband Router
setup.
2On the “Edit” menu, click “Preferences”.
3In “Category”, click “Advanced” and click the “Proxies” button.
4Select “Direct connection to the Internet” and click “OK”.
5When the Wireless Broadband Router setup is complete, return the proxy setting to
its original condition.
â– Java settings
Make sure that the Java settings of your Web browser are enabled. If they are not, do so.

Product specificaties

Merk: Sony
Categorie: Overige computer accessoire
Model: PCWA-AR800

Heb je hulp nodig?

Als je hulp nodig hebt met Sony PCWA-AR800 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Overige computer accessoire Sony

Sony

Sony PCWA-A220 Handleiding

18 Juni 2023
Sony

Sony GDM-500PS Handleiding

14 Juni 2023
Sony

Sony GDM-FW9011 Handleiding

31 Mei 2023
Sony

Sony PCGA-CCGX Handleiding

28 Mei 2023
Sony

Sony GDM-F520 Handleiding

15 Mei 2023
Sony

Sony GDM-C520 Handleiding

15 Mei 2023
Sony

Sony PRSA-CL1 Handleiding

12 Mei 2023
Sony

Sony PCGA-BP4V Handleiding

12 Mei 2023
Sony

Sony PCGA-CC1A Handleiding

12 Mei 2023
Sony

Sony PCGA-AC19V1 Handleiding

11 Mei 2023

Handleiding Overige computer accessoire

Nieuwste handleidingen voor Overige computer accessoire

Gabor

Gabor LTS-50 Handleiding

10 December 2024
Gembird

Gembird NBS-D1-04 Handleiding

10 December 2024
StarTech.com

StarTech.com DK30CHHPD Handleiding

7 December 2024
StarTech.com

StarTech.com 129UE-USBC-KVM-DOCK Handleiding

7 December 2024
IFM

IFM E12247 Handleiding

5 December 2024
Dell

Dell Universal Dock UD22 Handleiding

3 December 2024
Sharkoon

Sharkoon X-Rest PRO Handleiding

29 November 2024
Sharkoon

Sharkoon SHARK XTend 16 Handleiding

29 November 2024
SMK-Link

SMK-Link VP3610 Handleiding

26 November 2024
Dell

Dell 470-ACWN Handleiding

22 November 2024