Sonance Landscape LS4T SAT Handleiding

Sonance Speaker Landscape LS4T SAT

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Sonance Landscape LS4T SAT (5 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 85 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
SATELLITE SPEAKERS
I N S T R U C T I O N M A N U A L
LS4T SAT | LS6T SAT
Figure 2
Figure 1: Placement
Introduction
Thank you for purchasing SLS Speakers. When properly installed,
these speakers will provide you with years of outdoor entertainment
pleasure. To get the most out of your new speakers, please read
this manual thoroughly before you begin installation.
Satellite Placement
The SLS system is designed to deliver a seamless, evenly
dispersed sound īƒ„eld in an ā€˜open airā€™ environment. An array of
multiple Satellite speakers and Subwoofers should be strategically
placed to minimize ā€˜hot spotsā€™ and ā€˜nullsā€™ as you move around the
outdoor entertainment area. Recommended placement of the SLS
Satellite models is every 8-10 feet around the area of coverage.
The shorter spacing is recommended for higher SPL and closer
listening applications. After every 4-5 satellites, install one SLS
Subwoofer of choice within the speaker wire chain. This will
allow the output of the satellite speakers and subwoofer to blend
together more seamlessly. See Figure 1.
Use care to select satellite locations that are equally distant from
the main listening area. When possible, use high and low locations
to centralize the acoustic stage. See Figure 2.
Sonamp DSP 2-750 Ampliīƒ°er Power Planning
The maximum number of satellites and subwoofers that can be
used in a system will depend on the ampliīƒ„er power. It is important
to calculate the ampliīƒ„er power your installation will require before
you begin. Multiple ampliīƒ„ers may be required in large installations.
Refer to the SLS wattage calculator on the Sonance website:
www.sonance.com/outdoor/new-sls/satellite-speakers.
1
Adjustable Tap
This Sonance Landscape Series product features a wide bandwidth
Sonance Laminated Core Transformer (SLCT) with an adjustable
tap, allowing the system to be conīƒ„gured for 70V/100V or 8 ohm.
If using this SLS product in an 8 ohm application, ensure the tap
switch is positioned to the 8 ohm setting. If using this product in
a 70V/100V system, ensure the tap is positioned to one of the
70V/100V settings.
Some 70V/100V system designs will require variations of higher
and lower output in diī‘œerent areas of the landscaping. The SLCT
adjustable tap allows each satellite or subwoofer to be individually
dialed to the desired output. Adjusting the tap settings will impact
your wattage calculations. Please review the Wattage Calculator
on the Sonance website: www.sonance.com/outdoor/new-sls/
satellite-speakers for more information.
NOTE: AS A GENERAL GUIDELINE, (1) SATELLITE WILL COVER ABOUT 250
SQUARE FEET OF LISTENING AREA
Box Contents
(1) Satellite Speaker
(2) Silicone īƒ°lled wire nuts
LS4T SAT
Landscape Series Satellite Speaker
NOTE: THIS PRODUCT SHIPS WITH THE SLCT ADJUSTABLE TAP SET
TO 40W. ADJUSTMENTS CAN BE MADE TO THE TAP SWITCH ONCE ALL
THE SATELLITES AND SUBWOOFERS ARE CONNECTED TO ACHIEVE THE
APPROPRIATE OUTPUT LEVEL.
NOTE: ENSURE THAT ALL SATELLITES AND SUBWOOFERS ARE SET TO
EITHER 70V/100V OR 8 OHM TAP SETTINGS TO AVOID ANY DAMAGE TO
YOUR AMPLIFIER. DO NOT COMBINE PRODUCTS SET TO ANY OF THE
70V/100V SETTINGS WITH PRODUCTS SET TO THE 8 OHM SETTING ON A
SINGLE AMPLIFIER.
Figure 4: SLS Wiring Diagram
Conīƒ„guration: 4 SATs:1 SUB or up to 8 SATs:1 SUB
Figure 3: Connect
7. After all the speaker connections are completed, connect the
wires to your ampliīƒ„er. See Figure 4.
8. Turn your ampliīƒ„er on and test the system with your favorite
music. If the speakers are operating properly, reīƒ„ll the wire
trench and enjoy your new system.
Satellite Wiring and Installation
Sonance Landscape Series systems allow for speakers to be
daisy chained together. In a typical system with one zone of audio,
simply run a stereo or 4 conductor speaker wire from the ampliīƒ„er
to the closest speaker. Designate the īƒ„rst speaker as either left
or right and connect the appropriate positive and negative wires
to the speaker terminals. Continue alternating the wires between
the left and right channels for each speaker, creating a daisy chain
of stereo satellites. The Subwoofer can be wired anywhere in the
chain and will receive either left or right speaker wires. See Figure 4.
Twist wires
together
Waterproof
Wire Nuts
To next
speaker/subwoofer
To
Amplifier
Positive
+Negative
-
Expandable
Sonamp DSP 2-750 Amplifier
LS4T SATs & LS12T SUB/LS15T SUB or LS6T SATs & LS12T SUB/LS15T SUB
LeftLeft RightRight LeftLeft RightRight
4OHMSMIN
2. Once the accessories have been mounted at the desired
locations, mount the satellites by threading the mounting shaft
into the corresponding opening of the accessory.
2
NOTE: DO NOT STAKE SLS SPEAKERS WITHIN DIRECT SPRAY RANGE OF
SPRINKLER HEADS. KEEP AT A DISTANCE OF 2 FEET OR GREATER FROM
DIRECT WATER STREAMS.
NOTE: SONANCE STRONGLY RECOMMENDS THE USE OF 14/4 DIRECT
BURIAL WIRE FOR DISTANCES UP TO 200 FEET AND 12/4 DIRECT BURIAL
FOR LONGER RUNS. KEEP WIRES AS SHORT AS POSSIBLE TO MINIMIZE
RESISTIVE WIRE LOSSES.
CAUTION: THE AMPLIFIER SHOULD NOT BE CONNECTED TO AC POWER
UNTIL ALL SPEAKER WIRE CONNECTIONS ARE COMPLETED. HIGH POWER
70 VOLT AMPLIFIERS PRESENT A SERIOUS SHOCK HAZARD.
NOTE: BEFORE INSTALLING SATELLITE SPEAKERS, ENSURE THAT EACH
ONE HAS BEEN SET TO THE APPROPRIATE 70V/100V OR 8 OHM TAP
SETTING FOR YOUR SYSTEM DESIGN AND REQUIREMENTS.
1. Once Locations have been established, choose the appropriate
mounting accessories for the project. PLEASE NOTE: Always
use a #3 Phillips head screwdriver when īƒ„ne tuning the height
adjustment screw.
ā€¢ For applications on īƒ…at surfaces, such as the side of a
building or structure, use the SM1 Round Surface Mount.
See instruction manual included with accessory for precise
mounting instructions.
ā€¢ For placement directly into the ground, use the GS9 ABS
in-ground stake for the LS4T SAT, and/or the GP19 PVC
Ground Post for the LS6T SAT. See Instruction Manual
included with accessory for precise instructions.
ā€¢ For in-tree Mounting, use the TSMJB Tree / Surface Mounting
Junction Box. See Instruction Manual included with accessory
for precise instructions.
NOTE: ATTENTION MUST BE PAID TO THE ELECTRICAL LEADS TO AVOID
NICKS AND CUTS THAT MIGHT SHORT THE SYSTEM.
3. Prepare individual leads to be connected to main leads.
4. Dig a 4ā€ ā€“ 5ā€ deep trench for running the speaker wires.
5. Run the wire through the trench from the ampliīƒ„er to the īƒ„rst
speaker location.
6. Connect the direct burial wire to each speaker wire;
connections should be made with either silicone īƒ„lled wire
connectors or appropriate junction boxes. See Figure 3.
IMPORTANT: BE SURE NOT TO LET ANY STRAY ā€˜+ā€™ & ā€˜ā€“ā€™ STRANDS TOUCH
EACH OTHER. TOUCHING STRANDS CAN CAUSE A SHORT-CIRCUIT THAT
COULD DAMAGE YOUR AMPLIFIER AND DEGRADE SOUND QUALITY.
NOTE: THE SUBWOOFER
CAN BE CONNECTED
AT ANY POINT IN THE
DAISY CHAIN.


Product specificaties

Merk: Sonance
Categorie: Speaker
Model: Landscape LS4T SAT

Heb je hulp nodig?

Als je hulp nodig hebt met Sonance Landscape LS4T SAT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Sonance

Handleiding Speaker

Nieuwste handleidingen voor Speaker