Sonance Landscape HS10SUB Handleiding

Sonance Subwoofer Landscape HS10SUB

Lees hieronder de 📖 handleiding in het Nederlandse voor Sonance Landscape HS10SUB (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
1
Figure 1
HS10SUB Subwoofer
Subwoofer
HS10SUB HARDSCAPE SUBWOOFER
Introduction
Thank you for purchasing a SLS Subwoofer. When properly installed,
this subwoofer will provide you with years of outdoor entertainment
pleasure. To get the most out of your new subwoofer, please read
this manual thoroughly before you begin installation.
Box Contents
SLS Hardscape Subwoofer box contains:
(1) Hardscape Subwoofer
(2) Silicon Filled Wire Nuts
Figure 1 shows the SLS placed along the perimeter of the
entertainment area.
Select a central location for the subwoofer if using only one
subwoofer (see Figure 1) if using multiple subwoofers, select
locations that are the same distance from the main listening area.
Subwoofer Location Selection
The SLS is designed to deliver a seamless, evenly dispersed sound
eld in an ‘open air environment. An array of multiple Satellite
speakers and Subwoofers should be strategically placed to
minimize ‘hot spots’ and ‘nulls’ as you move around the outdoor
entertainment area.
Sonamp DSP 2-750
Amplier Power Planning
The maximum number of satellites and subwoofers that can
be used in a system will depend on the amplier power,
refer to the SLS wattage calculator on the Sonance website
(www.sonance.com/outdoor/sonance-landscape-series/subwoofers).
2
Subwoofer Installation
70 volt audio systems allow for speakers to be daisy chained
together. In a typical system with one zone of audio you simply run a
stereo or 4 conductor wire from the amplier to the closest speaker.
Once you have designated your rst speaker as either left or right,
continue alternating the wires between the left and right channels
creating a daisy chain of stereo satellites. The Subwoofer can be
wired anywhere in the chain. See Figure 5
1. Find the best location to compliment your other speakers.
2. Decide which channel the subwoofer will go on, calculate load.
See wattage calculator.
3. Connect to amplier wiring using the supplied wire nuts, see
Figure 4.
Twist
Wires
Together
Waterproof
Wire Nuts
From Speaker AmplifieTo
r
Positive
+Negative
-
Figure 4
4. Dig a 4” – 5” deep trench to run the speaker wires in.
5. Run the wire through the trench from your amplier to the rst
speaker location.
6. Connect the direct burial wire to each speaker wire, connections
should be made with either silicone lled wire connectors or
appropriate junction boxes. See Figure 4.
7. After all the speakers connections are completed, connect the
wires to your amplier. See Figure 5 for reference.
8. Turn your amplier on and test the system with your favorite
music. If the speakers are operating properly, rell the wire
trench and enjoy your new speakers.

Figure 5
3
Specications
Woofer: 10” (254mm) polypropylene cone
with a rubber surround
Frequency Response: 35Hz – 100Hz ±3dB
Power Required: 100 watts
Enclosure Material: HDPVC
(High Density Polyvinyl Chloride)
Non-corrosive sealed enclosure
Crossover: 100Hz
Available Finishes: Dark brown textured enclosure
Dimensions: Enclosure
13 1/2” wide, 13 1/2” deep, 14” high
(34.29cm x 34.29cm x 35.56cm)
Shipping Weight: 42 lbs (19 kg)
14”
13.5” 13.5”


Product specificaties

Merk: Sonance
Categorie: Subwoofer
Model: Landscape HS10SUB

Heb je hulp nodig?

Als je hulp nodig hebt met Sonance Landscape HS10SUB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Subwoofer Sonance

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer