Smeg PC681-1 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Smeg PC681-1 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
PC60 - PC68 - PC681
7
EN
Self-cleaning panels
PC60
PC68 - PC681
1 Left self-cleaning panel
2 Self-cleaning deflector
3 Right self-cleaning panel
The self-cleaning panels are coated in a
special enamel which aids progressive
elimination of grease splattering and
odours caused by cooking food.
Precautions
Avoid using anti-adhesive films (silicone)
and all maintenance products, particularly
harsh cleaning products.
Do not knock the self-cleaning coating or
use metal brushes or blunt objects to clean it.
Practical advice
The self-cleaning enamel will always
remain clean as long as stains are not
produced at a greater rate than they are
eliminated.
If production of stains increases, the
cleaning action will become insufficient and
the self-cleaning coating will become
ineffective.
After cooking food which leaves a large
amount of dirt and stains on the oven (e.g.
roast duck), it is necessary to heat the oven
up to maximum temperature while empty.
Cooking foods which do not splatter can
also be an opportunity to perform this
regeneration.
Do not cook food which could further stain
the oven before the dirt from the previous
cooking has been eliminated.
If the appliance has the “Vapor
Clean” function, do not point the
spray nozzle towards the
deflector.
PC60 - PC68 - PC681
8
Installation of the self-cleaning panels
1. Remove all accessories from inside the
oven (trays and drip trays).
2. Remove the frames: pull the frame
towards the inside of the oven to unhook
it from its groove A, then slide it out of the
seats at the back .B
3. Remove the deflector: unscrew the two
side screws holding the deflector to the
rear wall of the oven.
4. Replace the deflector with the new self-
cleaning deflector ( ): fasten it to the 2
rear wall of the oven using the screws
removed from the previous deflector.
PC60 - PC68 - PC681
9
EN
5. Place the left-hand self-cleaning panel
( ) on the corresponding oven wall.1
6. Hold the self-cleaning panel in position
on the wall and insert the frame first into
the seats at the back , then hook it into B
its groove .A
7. Repeat the operation with the right-hand
self-cleaning panel ( ).3
Regeneration of self-cleaning panels
(catalytic cycle)
The regeneration cycle of the self-cleaning
panels is a cleaning method through
heating suitable for removing small grease
residues, not sugar-based ones.
1. Clean the base and the upper guard first
with a microfibre cloth soaked in water
and neutral washing up liquid. Rinse
thoroughly.
2. Set a regeneration cycle by selecting a
fan assisted function at the maximum
temperature for one hour.
3. If the panels are particularly dirty after the
regeneration cycle, remove them and
wash them with neutral washing up
liquid. Rinse and dry them.
Put the panels back in the oven and set a
fan assisted function at a temperature of
180°C for one hour, in order to ensure that
they are thoroughly dry.
We recommend carrying out the
self-cleaning panel regeneration
cycle every 15 days.


Product specificaties

Merk: Smeg
Categorie: Niet gecategoriseerd
Model: PC681-1

Heb je hulp nodig?

Als je hulp nodig hebt met Smeg PC681-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Smeg

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd