Skytech 1001 - A remote control system Handleiding

Skytech Diversen 1001 - A remote control system

Lees hieronder de 📖 handleiding in het Nederlandse voor Skytech 1001 - A remote control system (6 pagina's) in de categorie Diversen. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

MODEL: 1001 - A

INSTALLATION AND OPERATION INSTRUCTIONS

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO

NOT ATTEMPT TO INSTALL OR OPERATE

INTRODUCTION

The transmitter operates on a 12V (A23) battery that is included. Install the 12V battery sup-

plied with the unit into the battery compartment. It is recommended that ALKALINE batteries

always be used for this product. Be sure the batteries are installed with the (+) and (-)

ends facing the correct direction.

The LED signal light should illuminate when either the ON or OFF button is pressed. If the

signal light does not illuminate, check the position of the transmitter’s battery, and if the bat-

tery is fully charged.

TRANSMITTER

REV 4/15/11 Page 1

This remote control system was developed to provide safe, reliable, user-friendly remote control system for gas heating appliances. The

system can be operated manually from the transmitter.

OFF

FRONTBACK

SIGNAL

LIGHT

ON/OFF

BUTTONS

BAT TERY

COMPARTMENT

RECEIVER

Install the (4) AA-size batteries supplied with the unit. It is recommended that ALKALINE batteries always be used for this product. Be

sure the batteries are installed with the (+) and (-) ends facing the correct direction.

ON• : will manually turn on the appliance.

REMOTE• : will allow use of handheld transmitter. If the system does not respond

to the transmitter on initial use, check the battery positions in the remote. If that

does not work, see the SECURITY CODE section.

OFF• : will disable the remote receiver.

It is suggested that the slide switch be placed in the OFF position if you will •

be away from your home for an extended period of time.

REMOTE

OFF

LEARN

Requires 4-AA 1.5V

alkaline batteries

Learning

button

Remote Receiver

Battery cover slides on/off

Slide

Switch

REMOTE

OFF

The remote receiver has a 3-position slide switch for selecting the mode of operation

ON/REMOTE/OFF

Skytech 1001-A

INSTALLATION

The remote receiver can be either wall-mounted in a standard plastic switch box (not metal) or placed on or near the replace hearth.

Preferably, the remote receiver should be wall-mounted in a plastic switch box, as this will protect its electronic components from the

heat produced by the gas appliance. The remote receiver should be kept away from temperatures exceeding 130º F. Battery life is

also signicantly shortened if batteries are exposed to temperatures 130ºF or higher.

Before installation make sure the remote receiver slide switch is in the OFF position. After installation be sure that the slide switch is

moved to the REMOTE position.

MOUNTING THE REMOTE RECEIVER

Position the receiver as shown in diagram to

the left with lower tab on cover plate inserted

into groove of receiver (Make sure LEARN

hole on cover plate properly aligns with remote

receiver). Pull receiver up and snap into top

tab of cover plate.

Position the cover plate so the word ON is fac-

ing up; then, install the remote receiver into the

plastic switch-box using the two long screws

provided. Push the white button over the re-

ceiver slide switch.

Remote Receiver

Cover Plate

(Rear View)

To attach Cover Plate to Receiver Box:

REV 4/15/11 Page 2

OFF

LEARN

WALL

Plastic Switch Box

Cover Plate

Receiver

Slide

Button

HEARTH MOUNT

The remote receiver can be placed on the replace hearth or under the re-•

place behind the control access panel.

Use the wires attached to the remote receiver to connect to the gas valve or •

the electric module (piggyback connectors have both male & female terminals

for exibility).

Be sure that the connectors do not touch each other or other bare metal •

surfaces; this will cause the appliance to turn on. The connectors may be

wrapped with electrical tape to prevent this.

WALL MOUNT

When wall mounting the remote receiver, longer wires (not included) are required to connect to the gas valve or electronic module.

These wires must:

Be at least 18 Gauge (AWG)•

Be no longer than 20’•

Have no splices•

WARNING

This remote control system must be installed exactly as outlined in these instructions. Read all instructions completely before at-

tempting installation. Follow instructions carefully during installation. Any modications of this remote control or any of its compo-

nents will void the warranty and may pose a re hazard.

Do not connect any gas valve or electronic module directly to 110-120VAC power. Consult gas appliance manufacturer’s instruc-

tions and wiring schematics for proper placement of all wires. All electronic modules are to be wired to manufacturer’s specica-

tions.

The following wiring diagrams are for illustration purpose only. Follow instructions from manufacturer of gas valve and/or electronic

module for correct wiring procedures. Improper installation of electric components can cause damage to electronic module, gas

valve and remote receiver.

Skytech 1001-A

ELECTRONIC SPARK SYSTEM CHECK

Slide the 3-position button on the remote receiver to the • ON position. The spark electrode should begin sparking to ignite the pilot.

Afterthepilotameislit,themaingasvalveshouldopenandthemaingasameshouldignite.

Slide the button to • OFF.Themaingasameandpilotameshouldbothextinguish.

Slide the button to • REMOTE,thenpresstheON button on the transmitter to change the system to on. The spark electrode should

beginsparkingtoignitethepilot.Afterthepilotislit,themaingasvalveshouldopenandthemaingasameshouldignite.

LEARNING TRANSMITTER TO RECEIVER

•

Each transmitter uses a unique security code. It will be necessary to press the LEARN button on the receiver to accept the trans-•

mittersecuritycodeuponinitialuse,ifbatteriesarereplaced,orifareplacementtransmitterispurchasedfromyourdealerorthe

factory.Inorderforthereceivertoacceptthetransmittersecuritycode,besuretheslidebuttononthereceiverisintheREMOTE

position;thereceiverwillnotLEARNiftheslideswitchisintheONorOFFposition.TheLEARNbuttoninlocatedonthefrontface

of the receiver; inside the small hole labeled LEARN. Using a small screwdriver or end of a paperclip gently press and release

the black LEARN button inside the hole. When you release the LEARN button the receiver will emit an audible “beep”. After the

receiver emits the beep press ANY transmitter button and release. The receiver will emit several beeps indicating that the transmit-

ter’s code has been accepted into the receiver.

REV 4/15/11 Page 3

WIRING ELECTRONIC SPARK IGNITIONS

ELECTRONIC MODULE

TR TH

REMOTE

RECEIVER

neutral wire

24VAC

hot wire

120VAC

110/24VAC

Transformer

Theremotecontrolreceivercanbeconnected,inseries,toa24VAC

transformertotheTR(transformer)terminalontheELECTRONIC

MODULE.Connectthehotwirefromthe24VACtransformertoeither

ofthewireterminalsontheremotereceiver.Connectanotherwirebe-

tween the other receiver wire terminal and the TH (thermostat) terminal

ontheELECTRONICMODULE.

WIRING INSTRUCTIONS

Aqualiedelectricianshouldinstalltheremotecontrolsystem.

TERMINAL BLOCK

ON MILLIVOLT

GAS VALVES

TP TP TH

THERMOPILE/

PILOT LIGHT

REMOTE

RECEIVER

ConnectonewirefromtheremotereceivertotheTHterminalonthegas•

valve.

ConnecttheotherwirefromtheremotereceivertotheTH/TPterminalon•

the gas valve.

WIRING MILLIVOLT VALVES

MILLIVOLT SYSTEM CHECK

Ensurethatthepilotameislit.•

Slide the 3-position button on the remote receiver to the • ONposition.Themaingasame(i.e.,there)

should ignite.

Slide the button to • OFF.Themainameshouldextinguish(thepilotamewillremainon).

Slide the button to • REMOTE,thenpresstheON button on the transmitter to change the system to on. The main

gasameshouldignite.

Skytech 1001-A

Product specificaties

Merk:	Skytech
Categorie:	Diversen
Model:	1001 - A remote control system

Heb je hulp nodig?

Als je hulp nodig hebt met Skytech 1001 - A remote control system stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Diversen Skytech

Skytech 1001 - A remote control system Handleiding

9 Januari 2023

Handleiding Diversen

Nieuwste handleidingen voor Diversen

Fysic FHP-160 Handleiding

23 Oktober 2023

Fysic FC-18 Handleiding

23 Oktober 2023

Fysic FC35 Handleiding

23 Oktober 2023

Ideen Welt Led stekkerdoos verlichting 323043-G Handleiding

17 Oktober 2023

Ideen Welt Thermo koeltas Handleiding

17 Oktober 2023

Ideen Welt Massage MV-25 Handleiding

17 Oktober 2023

Ideen Welt LED sensor LX-LD-P300 Handleiding

17 Oktober 2023

Ideen Welt ZF6865 8 LED Camping lamp Handleiding

17 Oktober 2023

Ideen Welt Muis snoerloos Handleiding

17 Oktober 2023

Ideen Welt Koffer weegscaal Handleiding

17 Oktober 2023