Simrad WR10 Handleiding

Simrad Marine WR10

Lees hieronder de 📖 handleiding in het Nederlandse voor Simrad WR10 (2 pagina's) in de categorie Marine. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
WR10 Wireless Autopilot Controller
and BT-1 Bluetooth Base Station
Quick Reference Guide
*988-10831-003*
Specications
Base station
Dimensions Ø 90 mm, H 38 mm (Ø 3.54” H 1.50”)
Power supply and interface 9-16 V DC via Micro-C network
Power consumption <100 mA at 12 V DC
Temperature Operating: -25°C to +60°C, Storage: -40°C to +85°C
Humidity 66°C, 95% RH, 18 hrs
Environmental protection IPx7
In-rush current 2 A for 20 ms (@ internal 5 V)
Connection cable: Micro-C drop cable 1.8 m (6 ft)
Signal wire gauge 24 AWG
Power wire gauge 22 AWG
Power wire resistance 5.7 ohms per 100 meters
Maximum current 3 A
Connector Micro-C T-Joiner
Remote controller
Dimensions H 72.64 mm, W 41.58 mm, D 22 mm, Weight:
Power supply 2 AAA batteries
Temperature Operating: -20°C to +55°C, Storage: -30°C to +70°C
Humidity 66°C, 95% RH, 18 hrs
Environmental protection IPx6, IPx7
Operation 5 buttons
Communication Bluetooth via Base station, range >30 m
Mounting Lanyard strap or wrist mounted
Accessories
Content of standard package
Dimensional drawings
Brand Supported autopilot systems
Simrad NAC-1, AC12, AC42, SG05
Simrad Pro AC70
Lowrance Outboard Pilot
B&G H5000, Triton
72.64 mm
(2.85”)
22.0 mm
(0.86”)
60 mm
2.36 “
41.58 mm (1.63”)
1 WR10 Wireless Autopilot Controller
2 AAA batteries
1 BT-1 Bluetooth Base Station
1 Micro-C drop cable 1.8 m (6 ft)
3 Lanyard straps (1 for each brand) + 1 carabiner clip
Wrist strap (000-12360-001)
x 2 x 2
Kit for pole mounting:
2 pcs. M4 30 mm stainless steel Phillips head mounting screws
(081-0008-11)
2 pcs. No. 6x 1.5 Phillips head bolts (083-0011-15)
Dash mount gasket (074-1253-000)
Mount Pole Cone (072-2970-000)
Pole mount locking nut (037-0105-00)
Micro-C drop cable 1,8 m (6 ft) (003-7872-00)
Micro-C T-Joiner (037-0491-01)
Mounting location of base station
Avoid installing the base station behind other electrical and electronic devices, as
they may interfere with the signal and consistency of wireless communication.
The base station should be at least 2 meters away from any other Bluetooth or wire-
less LAN (WiFi) transceiver.
It is advisable to check Bluetooth connection throughout the boat by pairing the
unit before permanently mounting the base station.
Operation
Keys and LED Action Mode: Auto Standby Wind NoDrift
< Left arrow Port or
> Right arrow Starboard
Short press: Adjust 1° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind mode.
√ √
Long press (2s): Adjust 10° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind
mode. √ √
< Left arrow +
> Right arrow
Autotack (in Wind mode), press and hold until LED is flashing green rapidly, then press AUTO to confirm.
STBY Place the autopilot into Standby mode.
MODE Changes the autopilot mode:
1. Boats set to SAIL: Toggles AUTO and WIND modes.
2. Other boat types: Toggles AUTO and NoDrift modes.
AUTO Engages the autopilot into AUTO mode.
LED* Green for 1s indicates message acknowledged. Red for 1s indicates message is either rejected or not acknowledged.
Green rapid flashes for up to 10s, followed by solid green for 1s. Red for 1s indicates message is either rejected or not
acknowledged.
* Note: In addition to the LED behaviour specified: Red will flash for 1s every 10s when battery level is low.
X X
X
X
Electromagnetic
Interference
0.5 m (20”) Min 0.5 m (20”) Min
2 m (6 ft) Min
RADAR
Magnetic Field
Radio Transmitter
X
Surface mount the base station
3 mm
19 mm
1
4
5
3
2
Use of Lanyard strap or wristband Add/replace batteries
WR10 Wireless Autopilot Controller operates
on 2 AAA batteries. Remove the cover to add
or replace the batteries.
Wiring the base station
A1.8 m (6 ft) Micro-C drop
cable (male to female)
BMicro-C T-Joiner
CMicro-C backbone
A
B
C
First, make sure that:
- the batteries in the remote are not low.
- the remote and the base station are placed as close together as possible.
- the AP system is OFF or in standby.
Then continue to:
1. Remove power from the base station.
2. Press and hold the buttons MODE and STBY on the remote for at least 5 seconds
until a single quick green LED flashes. The remote is now in Discoverable mode and
will stay in this mode for 60 seconds or until base station asks to pair.
3. Power up base station. For the first 10 seconds, the base station will search for
Discoverable remotes.
4. Wait till remote quickly flashes the green LED every second, indicating that the base
station is asking to pair.
5. Press the AUTO button for at least 1 second to start the pairing.
- When succesfully paired: The green LED will stay on for 2 seconds.
- When pairing failed: The red LED will stay on for 2 seconds.
Pairing a remote to the base station
Use Philips screw-
driver size #1 to en-
sure proper torque
when reassembling.


Product specificaties

Merk: Simrad
Categorie: Marine
Model: WR10

Heb je hulp nodig?

Als je hulp nodig hebt met Simrad WR10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Marine Simrad

Handleiding Marine

Nieuwste handleidingen voor Marine