Simrad Fluid Level Sensor Handleiding

Simrad Niet gecategoriseerd Fluid Level Sensor

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Simrad Fluid Level Sensor (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
*988-10921-001*
Whatā€™s in the box
Fluid Level Sensor
Installation Guide
Tools required Overview
Plan the installation
The sensor is designed to be the only device receiving signals
from the sending unit. If the sensor is replacing a previous gauge,
make sure you remove all the old gauge wires before you begin.
If this is a replacement, note which connection is positive before
disconnecting the old wires.
This document assumes the mounting bracket is connected to
the ļ¬‚uid level arm (or potentiometer) and is already installed in
the tank. The sensors wires ā€” red (positive) and black (negative)
ā€” will connect to the sending unitā€™s mounting bracket, on top of
the tank.
Use one Fluid Level Sensor for each diļ¬€erent ļ¬‚uid tank. When
having 2 diļ¬€erent tanks of similar ļ¬‚uids it is advisable to label
them so they can be identiļ¬ed in the NMEA 2000 device list in
the gauge or multi-function display.
Install the Fluid Level Sensor
Attach marine-grade crimp-on connectors to both the red lead
(+) and the black (-) lead. The Fluid Level Sensor must be the
ONLY device connected to the sender
Attach the positive red
lead to the sending unitā€™s
positive connector, usually
located in the center of the
mounting plate. Connect
the negative black lead to
the sending unitā€™s negative
connector. To ensure you
know which connection
is which, refer to the
mounting instructions that
came with the sending unit.
Wire Pliers
Drill with 22 mm (7/8ā€ ) drill bit
Marine-grade Crimp-on wire
connectors
Zip ties for securing Fluid Level
Sensor
The Fluid Level Sensor is designed to monitor fuel, live well, oil,
fresh water, waste water (gray water), and black water tanks.
!You should read all of the installation instructions
before proceeding. Decide where to install all components
before drilling any holes in your vessel.
The sensor is pre-conļ¬gured to the US marine standard of 33.5-
240 ohm. Please refer to your operations guide for conļ¬guration
information.
! Do NOT connect the
sensors to the NMEA
2000 network until you
have ī˜Ÿnished connecting
the red and black leads to
the sending unit. This re-
duces the risk of a spark
when working around
fuel tanks.
Other parts required
Fluid Level Sensor
NMEA 2000 T-Joiner
A Red wire for positive connector in ļ¬‚uid level ļ¬‚oat
B Black wire for negative connector in ļ¬‚uid level ļ¬‚oat
C Fluid Level Sensor
D NMEA 2000 connector
A Fluid tank
B Fluid Level Sensor
C NMEA 2000 CAN bus
backbone
Positive
Connector
(Red)
Negative
Connector
(Black)
A
C
D
B
46 cm
(18ā€)
3 m
(9.8ā€™)
Dimensions
Connect the Fluid Level Sensor to the network
A
B
C
A Fluid Level Sensor
B NMEA 2000 CAN bus backbone
C 12 V DC Power supply.
Connect via a switch and 5 amp fuse
D Fluid Level Sender
E Cable/wire leading to the Fluid Level Float in the tank
Speciī˜Ÿcations
Compatible with most sending units that are calibrated
between 33 and 240 ohm.
PGNs transmitted
59392 ā€“ ISO Acknowledgment
59904 ā€“ ISO Request
60928 ā€“ ISO Address Claim
126996 ā€“ Product Information
127505 - Fluid Level
A
B
D
E
C
86.5 mm
(3.4ā€)
17.1 mm
(0.67ā€)
9.6 mm
(0.38ā€)
20 mm
(0.8ā€)
11.5 mm
(0.45ā€)


Product specificaties

Merk: Simrad
Categorie: Niet gecategoriseerd
Model: Fluid Level Sensor

Heb je hulp nodig?

Als je hulp nodig hebt met Simrad Fluid Level Sensor stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Simrad

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd