SIIG CE-MT0F11-S1 Handleiding

SIIG Muurbeugels CE-MT0F11-S1

Lees hieronder de 📖 handleiding in het Nederlandse voor SIIG CE-MT0F11-S1 (8 pagina's) in de categorie Muurbeugels. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

04-0658A

TV Size: 23" - 42”

Max load capacity: 99lbs / 45kg

Wall distance: 0.43" / 11mm

Bubble level included

Ultra-Thin LED/LCD TV Mount - 23" to 42"

IMPORTANT: If you don't understand the installation instructions, please consult an installation

specialist

Ultra-Thin LED/LCD TV Wall Mount

Material: 2.0mm Cold Rolled Steel Plate

Installation Instructions

Universal Mounting Pattern

Caution

A F

B G

C H-1 (x4) M6 Washer

(×4) M6×12 screw

(×4) M5×12 screw

(×4) M8×15 screw

H-2 External bubble level

(×4) M8/M6 rectangular

washer

It is recommended that two people perform the installation. Injury and/or damage can result from dropping or

mishandling the display.

INSTALLATION AND OPERATING INSTRUCTIONS

Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source. Failure

to do so may result in damage to the display and could increase the risk of fire.

The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the wall

must be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in the

installation instructions, must be adhered to. Failure to do so could result in serious personal injury.

Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any

surface other than wood studs or concrete, use suitable hardware (not included but commercially available).

(×4) M6 x 50 bolt

Prior to the installation of this product, the installation instructions should be read and completely understood. The

installation instructions must be read to prevent personal injury and property damage. Keep these installation

instructions in an easily accessible location for future reference.

CAUTION: The maximum load capacity is 99lbs. Use with products exceeding the maximum load capacity may

cause serious injury. See apparatus instructions.

When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is

recommended that the wood studs be a minimum of 16" apart.

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result

in damage to the display and/or damage to the mounting surface.

Hardware Kit

(×4) M4×12 screw

(x4) M6 concrete anchor

a) Wood Stud Installation

You should mark two positions total.

Stud finder for drywall installation

NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.

Use a high-quality electronic stud finder (commercially available) to locate dead center of two wood studs and

mark their locations with a pencil.

Step 1: Wall Plate Installation

Tools Required

Phillips head screw driver

Attach the bubble level (H-2) to the wall plate and with the help of an assistant ensure the wall plate is level,

position the wall plate against the wall in the desired mounting location.

Mark the right and the left positions of the small horizontal slots that are in alignment with the studs.

CAUTION: Do not over-tighten bolts - doing so may cause unnecessary damage to the wall.

Tighten the bolts with a 7/16" socket or 7/16" open-end wrench by turning clockwise until tight.

For each location, thread bolt (F) through washer (H-1) and insert into the wall. Do not tighten until all bolts are in

place.

Pre-drill a 1/8" hole to a depth of approximately 2" in the wood stud at each marked location.

Level

7/16" socket & socket wrench and/or 7/16" open-end wrench

Drill, 1/8" (3mm) drill bit for wood stud installation and 5/16" (8mm) masonry drill bit for concrete/brick installation

CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.

6 Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level to

verify that the wall plate is level.

Product specificaties

Merk:	SIIG
Categorie:	Muurbeugels
Model:	CE-MT0F11-S1
Kleur van het product:	Zwart
Breedte:	450 mm
Diepte:	11 mm
Hoogte:	380 mm
Materiaal behuizing:	Staal
Montagewijze:	Muur
Geschikt voor schermmaten:	23 - 42 "
Maximale gewichtscapaciteit:	45 kg
Gewicht (imperiaal):	3 lbs
Compatibiliteit:	LCD, LED, Plasma
Montage interface compatibiliteit (min):	200 x 100 mm
Montage interface compatibiliteit (max):	200 x 200 mm