SIIG CE-H23B11-S1 Handleiding

SIIG AV extender CE-H23B11-S1

Lees hieronder de 📖 handleiding in het Nederlandse voor SIIG CE-H23B11-S1 (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Important Instructions

• Suggest using IGMP Gigabit switches

• Do not mix up transmitter and receiver

before installation

• Channel of each transmitter(TX) must be

unique, otherwise, the system could break

down (including transmitter, receiver, IGMP

switch etc.)

Product Features

1. Resolution supported up to 1080p @60Hz

2. Transmission distance up to 120 meters (CAT6)

3. Support IR pass back function to control the

source device from RX location

4. Oers scalable TX/RX matrix conguration,

allows up to 256 total units, limited to 100

transmitters, additional transmitter units (part#

CE-H23B11) and receiver units (part# CE-

H23C11) sold separately

5. Supports computer control software to select

and switch between source devices .

Package Contents

1. Transmitter unit

2. Receiver unit

3. User Guide

4. IR blaster extension cable

5. IR receiver extension cable

6. DC5V/2A power adapter (x2)

7. Remote control

8. 3 pin phoenix connector (x2)

9. Wall-mount kit (x2)

10. Screws (x8)

Layout

• Transmitter unit

OUTPUT GND RX TX

RS-232

1. IR window: remote control channel

2. Power indicator

3. TX ID: Indicator of the current TX’s number

4. Reset button

5. DC 5V/2A power jack

6. Data transmission indicator

7. RJ45 output

8. Connection indicator

9. IR blaster extension cable interface

10. HDMI local signal output

11. HDMI signal input

12. RS-232 connector

• Receiver unit

G ND RX TX

RS-232

1. RX ID: Mark receiver unit as a number,

Indicator of the current RX’s number

2. IR window: remote control channel

3. Power indicator

4. TX connected: Indicator the input channel

as a number, and when the cahannel of

receiver as same as the channel of trans

mitter, transmission connected

5. Reset button

6. DC 5V/2A power jack

7. Data transmission indicator

8. RJ45 input

9. Connection indicator

10. IR receiver extension cable interface

11. HDMI signal output

12. RS-232 connector

Application

• Point to point

OUTP UT

RJ45

23 2

GND

• Matrix conguration

Note: Dedicated LANs with IGMP Gigabit Ethernet switches are

recommended for reliable performance. Installing on mixed LANs

may adversly eect performance is not supported.

RS232 bi-direction function

• Baud rate

Different encoding mechanism can not mix-

connected, the baud rate of RS232 serial of these

transmitter unit and receiver unit, support 2400,

4800, 9600, 19200, 28800, 38400, 57600, and

115200

If the RS232 serial does not work by above con-

nection, please try to change the order of TXD

line and RXD line.

• Check baud rate:

I f y o u n e e d t o c h e c k t h e b a u d r a t e .

Before powering on, set the baud rate to

115200 on your seria l port test tool and

power on. When the RS232 serial of the product

co n n ec te d to se ri a l po rt te s t to o l , th e

s o f t w a r e w i l l r e a d o u t t h e b a u d r a te .

E.g.: The software shows information “ Baud rate:

9600”, and it means 9600 is the current baud rate.

• Set baud rate

For example, the current baud rate of extenders

are 9600, but the baud rate of control equipment

is 19200. In this case, choose baud rate 9600 for

serial port tool, then input command “set: 19200”

in character format and send it out. (set: xxxxx

have to send all at once in command line)

IR use guide

• IR passback

IR blaster cable should be pluged into the IR-out

of Transmitter, and the IR receiver cable should

be pluged into the IR-in port of the Receiver. The

emitter of IR blaster cable should be as close as

possible to the IR receiver window of the signal

source device.

• IR remote control

Using the IR remote controll to set/select the

channel of this HDMI Extender.

Button control

The left button controls the value of the left

Nixie tube, and the right one to control the value

of the right Nixie tube. When the value of “TX

connected” on the RX unit matches the value of

“TX ID” on the TX unit, the devices will pair/link

successfully.

Reset device to default

“TX ID” on TX unit and “TX connected ”on the RX

unit. Press both buttons simultaneously and hold

them down for 3 seconds to reset to default.

Computer control software (Windows)

1. HDbitT E-Matrix Download software “

Control center“ from http://www.hdbitt.

com/download-matrix/

2. Set PC’s IP to 192.168.1.xxx, then connect

your PC to the Ethernet switch which has

the same subnet with TX and RX units.

3. Open the software HDbitT E-Matrix Control

center and scan for devices.

• IP setting

TX and RX have their own default IP address, TX’s

IP is 192.168.1.238, and RX’s IP is 192.168.1.239.

Generally, there is no need to change the device

IP address, as the system can work normally

even though multiple TX units and multiple RX

units connected into the LAN have the same IP

address.

If IP change is required, follow the instructions on

the next page.

• Device setting

Set device name, ID, Channel then click "Update"

button to save conguration

• Pre-operation mode setting

Support

For more info or tech support

http://www.siig.com/support

HDMI Over IP Extender with IR

User Guide

04-1129A

• Operation mode selection setting

Click “Select Mode” button and choose the mode

needed, then click "Update" button

Wireless Control APP

Requires installing a wireless access point on your

dedicated IGMP LAN.

• Download the Android or Apple wireless APP at

www.hdbitt.com/download-matrix

• Connect to the wireless access point which has

the same subnet as the TX and RX units

• TX ID, RX ID, TX connected number can be

reset by this APP, along with editing the device

name

Product specificaties

Merk:	SIIG
Categorie:	AV extender
Model:	CE-H23B11-S1
Kleur van het product:	Zwart
Gewicht:	272 g
Breedte:	133 mm
Diepte:	83 mm
Hoogte:	23 mm
Soort:	AV-zender
Gebruikershandleiding:	Ja
Montage gereedschap:	Ja
Connectiviteitstechnologie:	Bedraad
Ondersteunde video-modi:	480p, 720p, 1080i, 1080p
Maximum resolutie:	- Pixels
Videocompressieformaten:	H.264
Meegeleverde kabels:	IR
Inclusief AC-adapter:	Ja
Certificering:	FCC, CE
HDCP:	Ja
Maximale refresh snelheid:	60 Hz
Aansluiting voor netstroomadapter:	Ja
Materiaal:	Metaal
HDMI versie:	1.3
Duurzaamheidscertificaten:	RoHS
Temperatuur bij opslag:	-10 - 60 °C
Output current:	2 A
Remote (IR) uitgang:	1
HDMI in:	1
RJ-45 uitgang ports:	1
HDCP versie:	1.4
Aantal HDMI-uitgangen:	1
Operating voltage:	5 V
Afstandsbediening inbegrepen:	Ja
Maximaal bereik:	120 m
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Ondersteundende kabel types:	Cat5, Cat5e, Cat6