Shure UA874Z Handleiding

Shure Niet gecategoriseerd UA874Z

Lees hieronder de 📖 handleiding in het Nederlandse voor Shure UA874Z (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

General Description

The Shure UA874 uses a log periodic dipole array to offer enhanced reception

when directed toward the desired coverage area. An integrated amplifier and

four gain settings compensate for varying degrees of coaxial cable signal

loss. The UA874 can be mounted on a microphone stand, suspended from

the ceiling, or mounted to a wall using the integrated swivel adapter.

Features

• Low-noise signal amplifier compensates for insertion loss in coaxial cable

• Compatible with Shure wireless receivers and antenna distribution sys-

tems that provide 10–15 V DC bias

• Integrated threaded adapter mounts easily to microphone stands

• Four-position gain selector switch

• Shure quality, ruggedness, and reliability

Note: will not operate The antenna without 10-15 V DC bias. This is required

even at -6 dB and 0 dB ("passive") gain settings.

Installation

• Connect the antenna to the receiver or distribution system using Shure

antenna cables (or any 50 ohm, low-loss coaxial cable, such as RG-8U).

• The antenna only operates with receivers or distribution systems that

provide 10–15 V DC bias.

• Lower the gain setting for short cable runs, or increase gain for longer

runs. Note that the quality of the cable, not just the length, contributes

to signal loss. A lighter-grade 50 foot cable may require more gain than

a 100 foot, low-loss cable. Contact the cable manufacturer for cable loss

specifications.

• Direct the antenna toward the intended coverage area.

• Do not use this antenna for transmitting (such as with PSM transmitters)

Cable Maintenance

To maintain top performance for antenna cables:

• Avoid sharp bends or kinks in the cables.

• Do not deform cables with makeshift clamps, such as bending a nail over

the cable.

• Do not use in permanent outdoor installations.

• Do not expose to extreme moisture.

Selecting Antenna Cables

Use 50 ohm low-loss coaxial cable, such as RG-8U. Shure offers pre-termi-

nated antenna cables ranging from 6 to 100 feet.

NOTE: When ordering cables from Shure, select the low-loss "Z" models

(available for longer cables) when using frequency bands above 1000 MHz.

Interface

① Gain Switch

Adjust the four-position gain switch to compensate for the calculated cable loss, based on the length and type of cable.

Caution: There may be a small RF dropout when changing the gain setting.

UA874Z

Active Directional Antenna

② Gain Mode LED

Indicates the current gain switch setting.

③ RF Overload LED

Indicates a strong RF signal that is overloading the antenna amplifier, which results in distortion or poor performance. Increase the distance between the antenna

and transmitter, or lower the antenna gain setting.

NOTE: RF Overload LED does not operate for passive gain settings (−6 dB or 0 dB).

④ BNC Connector

Connect to a receiver or antenna combiner with RF inputs that supply 10–15 V DC bias.

Antenna Placement

Use the following guidelines when mounting antennas:

• Antennas and receivers must be from the same band.

• Mount antennas one wavelength (two feet) apart.at least

• Position antennas so there is nothing obstructing a line of sight to the transmitter (including the audience).

• Keep antennas away from metal objects.

Important: Always perform a "walk around" test to verify coverage before using a wireless system during a speech or performance. Experiment with antenna

placement to find the optimum location. If necessary, mark "trouble spots" and ask presenters or performers to avoid those areas.

Shure IncorporatedUA874Z Active Directional Antenna

2017/11/022/4

Setting Gain

The gain setting should only be used to compensate for the calculated cable

signal loss. Additional signal gain does not mean better RF performance.

Too much gain actually reduces reception range and the number of available

channels. This is because Shure receivers are optimized to deliver the best

performance when the sum of signal gain and cable loss equals 0 dB. Addi-

tional gain just amplifies everything in the RF range—including interference

and ambient RF noise. It cannot selectively increase the signal from the

transmitter.

• Use the lowest gain setting necessary to achieve good reception of the

transmitter RF signal, as indicated on the receiver’s RF LED or meter.

• Only increase the gain setting to compensate for the calculated cable

loss.

• The −6 dB gain setting can be useful for applications with short cable

runs (25 feet or less) and where the distance between the transmitter

and antenna is less than 100 feet.

• Reduce gain if the antenna LED illuminates—the signal isRF Overload

strong enough, so gain is not needed.

Calculating Gain Settings

To calculate the required gain setting, obtain the cable manufacturer's

specification for signal loss. The rated loss usually varies with RF frequency

in addition to cable length.

Multiply the per 100 feet rating of the cable by cable length to determine

signal loss, and add gain as necessary to compensate. For example: a 50

ft. cable with rated loss of -12dB per 100 ft. would calculate as

(-12dB/100)*50 = -6dB and require +6dB of gain for a sum total of 0

dB loss.

Find More Information Online

For more information, visit http://www.shure.com

Specifications

Connector Type

BNC, Female

Impedance

50 Ω

Power Requirements

10 to 15 V DC bias from coaxial connection, 75 mA

RF Frequency Range

470–698 MHzUA874US

470–790 MHzUA874E

470–900 MHzUA874WB

1240–1260 MHzUA874Z16

1492–1525 MHzUA874Z17

1785–1805 MHzUA874Z18

925–952 MHzUA874X

902–960 MHzUA874XA

Reception Pattern

3 dB Beam Width

70 degrees

Third-order Overload Intercept Point (OIP3)

>30 dBm

Antenna Gain

On Axis

7.5dBi

Signal Gain

±1 dB, Switchable

+12 dB, +6 dB, 0 dB, −6 dB

RF Overload LED Threshold

−5 dBm

Dimensions

316 x 359 x 36 mm (H x W x D)UA874

224 x 234 x 36 mm (H x W x D)UA874X

224 x 234 x 36 mm (H x W x D)UA874XA

224 x 234 x 36 mm (H x W x D)UA874Z

Weight

317 g (11.2 oz.)UA874

213 g (7.5 oz.)UA874X

213 g (7.5 oz.)UA874XA

213 g (7.5 oz.)UA874Z

Operating Temperature Range

−18°C (0°F) to 63°C (145°F)

Storage Temperature Range

−29°C (-20°F) to 74°C (165°F)

0RF overload LED does not operate for passive gain settings

Shure IncorporatedUA874Z Active Directional Antenna

3/42017/11/02

Product specificaties

Merk:	Shure
Categorie:	Niet gecategoriseerd
Model:	UA874Z

Heb je hulp nodig?

Als je hulp nodig hebt met Shure UA874Z stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Shure

Shure Plus Channels Handleiding

25 September 2024

Shure Plus PLAY Handleiding

25 September 2024

Shure UA864 Handleiding

24 September 2024

Shure Microflex Complete Handleiding

22 Augustus 2024

Shure SLXD5 Handleiding

6 April 2024

Shure Wireless Workbench 7 Handleiding

19 Juli 2023

Shure ULX-S Handleiding

8 Juli 2023

Shure GLXD14+/SM31FH Handleiding

7 Juli 2023

Shure GLXD14+/85 Handleiding

6 Juli 2023

Shure GLXD24R+/SM58 Handleiding

28 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024

Kolcraft MLB New York Yankees Handleiding

26 November 2024

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024

Nedis POCO106 Handleiding

26 November 2024

Nedis BTSM1GY Handleiding

26 November 2024

Turbosound TPOLEAJ-01 Handleiding

26 November 2024

Turbosound TSTAND-01 Handleiding

26 November 2024

IFM TAD981 Handleiding

26 November 2024

IFM TAD961 Handleiding

26 November 2024