Shure MX418 Handleiding

Shure Microfoon MX418

Lees hieronder de 📖 handleiding in het Nederlandse voor Shure MX418 (20 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/20

MX412DMX418D

Printed in U.S.A.

www.shure.com

27A14051 (Rev. 2)

MX400D

/C (R185)

/S (R184)

Shure Microflex® MX400D Series microphones

are miniature electret condenser gooseneck mi-

crophones with a desktop base and a 3 m (10 ft.)

cable. Desktop base allows microphones to be

used in multi-purpose rooms where quick setup

is required, or where permanent installation is

impractical.

Features

• Wide dynamic range and frequency response

for accurate sound reproduction

• Interchangeable cartridges that provide a

choice of polar pattern for each application

• Programmable mute button and LED indicator

• Logic input and output terminals for remote

control or use with automatic microphone

mixers

• Balanced, transformerless output for increased

immunity to noise over long cable runs

• RF filtering

MX400 Series Model Variations

MX400 microphones are available with 305 mm

(12 in.) or 457 mm (18 in.) goosenecks.

• “S” models include a mute button and LED.

• “D” models include a desktop base with

programmable mute button and LED and logic

input and output.

• “SE” models feature a surface mount flange

with side-exit cable.

The polar pattern of the included cartridge is indi-

cated by a model number suffix:

/C Cardioid

/S Supercardioid

/N Cartridge not included

Interchangeable Cartridges

Microflex microphones use

interchangeable cartridges

that allow you to choose

the polar pattern for differ-

ent installations.

Snap-Fit Windscreen

• Snap into the groove

below the cartridge.

• To remove, spread

the gap with a

screwdriver or

thumbnail.

• Provides 30 dB of

“pop” protection.

Microphone Placement

• Aim the microphone toward the desired source,

such as the talker.

• Aim it away from any unwanted source, such

as a loudspeaker.

• Place the microphone within 15 to 30cm (6 to

12 in.) of the desired sound source.

• Always use the supplied windscreen or optional

metal windscreen to control breath noise.

• If four or more microphones will be open at

the same time, use of an automatic mixer,

such as the Shure SCM810 or SCM410, is

recommended.

Securing to a Surface

Desktop Microphones

R183 Omnidirectional

R184 Supercardioid

R185 Cardioid

Connecting to an Automatic Mixer

Use these settings if connecting the microphone

to an automatic mixer or other device that mutes

audio and controls the LED.

1. Connect logic leads to the automatic mixer.

Connect the LED IN to the gate output to illumi-

nate the LED when that channel is gated on.

2. Set DIP switch 3 on. This disbles the mute but-

ton (the microphone passes audio regardless of

whether the button is pressed or not).

3. Set DIP switch 1 to configure how the mute but-

ton sends SWITCH OUT logic:

Logic Wiring

Green (LOGIC GROUND): Connects to the logic

ground of an automatic mixer, switcher, or other

equipment.

Orange (LED IN): Set DIP switch 3 on to use LED

IN. When shorted to LOGIC GROUND, the LED

turns on.

White (SWITCH OUT): Provides TTL logic (0 Vdc

or 5 Vdc) in response to the mute button. Set DIP

switch 1 for momentary or toggle. When phantom

power is applied, logic initializes high (5 Vdc). DIP

switch 2 has no effect on SWITCH OUT.

DIP Switches

Use the DIP switches to configure logic settings

and mute button behavior.

The DIP switches are covered with a piece of

clear tape at the factory. Remove tape to modify

the switch settings.

OFF (factory

default)

1 Momentary Toggle

2 Push-to-mute Push-to-talk

3 Mute button enabled,

LED illuminates when

mic is active

Disable mute button

(microphone always

on), logic controls

LED

4 -- --

Changing SWITCH OUT to Always

Momentary

Use the following modification in situations where

your logic interface requires momentary closure

of the SWITCH OUT, but you want the mute but-

ton to toggle the microphone (DIP switch 1 ON, 3

OFF):

1. Access the circuit board in-

side the microphone base.

2. Remove the resistor at R45

and reinstall it at location

R46.

Mute Button Configuration

Use DIP switches 1 and 2 to configure the mute

button, as follows.

Be sure to set DIP switch 3 (factory default) off

so that the mute button controls audio from the

microphone.

Switch Function DIP Switch Setting

Momentary: push-to-mute

(as shipped).

Momentary: push-to-talk

Toggle: (Push On/Push

Off): Mic is active when

powered on

Toggle: (Push On/Push

Off): Mic is mute when

powered on

Momentary:

push = 0 Vdc,

release = 5 Vdc

Toggle:

initial = 5 Vdc,

push = 0 Vdc

Wiring Diagram

NOTE: Audio and logic ground are connected at

microphone base.

Ground (Green)

SWITCH OUT (White)

LED IN (Orange)

Audio + (Red)

Audio – (Black)

NOTE: Bottom

cover must

be closed for

microphone to

function.

Product specificaties

Merk:	Shure
Categorie:	Microfoon
Model:	MX418
Kleur van het product:	Zwart
Soort:	Presentatiemicrofoon
Connectiviteitstechnologie:	Bedraad
Aansluiting:	XLR-3
Gevoeligheid microfoon:	-33.5 dB
Frequentie microfoon:	50 - 17000 Hz
Bedrijfstemperatuur (T-T):	-18 - 57 °C
Aantal producten inbegrepen:	1 stuk(s)
Output impedance:	180 Ohm