Shimano BL-MX70 Handleiding

Shimano Niet gecategoriseerd BL-MX70

Lees hieronder de 📖 handleiding in het Nederlandse voor Shimano BL-MX70 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

4. Pass the inner cable through the inner cable lead, and

after setting so that the total of the clearances between

the left and right shoes and the rim is 2 mm, tighten the

cable fixing bolt.

General Safety Information

WARNING

• Improper use of your bicycle's brake system may result in a loss

of control or an accident, which could lead to a severe injury.

Because each bicycle may handle differently, be sure to learn the

proper braking technique (including brake lever pressure and

bicycle control characteristics) for your bicycle.

Consult your bicycle dealer and the bicycle's owners manual, and

practice your riding and braking technique.

• If the front brake is applied too strongly, the wheel may lock and

the bicycle may fall forward, and serious injury may result.

• Brakes designed for use as rear brakes should not be used as

front brakes.

• Obtain and read the service instructions carefully prior to

installing the parts. Loose, worn or damaged parts may cause

the bicycle to fall over and serious injury may occur as a result.

We strongly recommend only using genuine Shimano replacement

parts.

• Be careful not to allow any oil or grease to get onto the brake

shoes. If any oil or grease do get on the shoes, you should

replace the shoes, otherwise the brakes may not work correctly.

• Check the brake cable for rust and fraying, and replace the cable

immediately if any such problems are found. If this is not done, the

brakes may not work correctly.

• Always make sure that the brakes are working correctly before

you ride the bicycle.

• The required braking distance will be longer during wet weather.

Reduce your speed and apply the brakes early and gently.

• If the road surface is wet, the tires will skid more easily. If the tires

skid, you may fall off the bicycle. To avoid this, reduce your speed

and apply the brakes early and gently.

• Read these Technical Service Instructions carefully, and keep

them in a safe place for later reference.

– To avoid serious injuries:

WARNING

Use the BR-MX70 V-BRAKE brake with V-BRAKE brake-

compatible brake levers such as the BL-MX70 brake levers.

Note

• The BR-MX70 V-BRAKE brake can only be used as a rear brake.

• The optimum efficiency of the Multi-Condition Brake System can

be realized by using the brakes and brake levers in the

recommended set.

• If the brake shoes have worn down until the grooves are no longer

visible, they should be replaced.

• Different brake shoes have their own characteristics. Ask the place

of purchase for details when purchasing the brake shoes.

• Parts are not guaranteed against natural wear or deterioration

resulting from normal use.

• For maximum performance we highly recommend Shimano

lubricants and maintenance products.

• For any questions regarding methods of handling or maintenance,

please contact the place of purchase.

– To avoid serious injuries:

Shimano BR-MX70 Safety Information

Use a 5 mm Allen key to install the brake lever.

When installing the components to carbon frame/handle bar

surfaces, verify with the manufacturer of the carbon

frame/parts for their recommendation on tightening torque

in order to prevent over tightening that can cause damage

to the carbon material and/or under tightening that can

cause lack of fixing strength for the components.

FORWARD

11 22

1 mm 1 mm

BL-MX70

JAPAN

22.2

FOR WAR DR

FORWARDR

Series

Brake lever

V-BRAKE brake

Brake cable

DXR

BL-MX70

BR-MX70

Multi-Condition

Brake System

In order to realize the best performance, we

recommend that the following combination be

used.

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222

3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

* Service Instructions in further languages are available at :

http://techdocs.shimano.com

Please note: specifications are subject to change for improvement without notice. (English)

Technical Service

Instructions SI-8ED0A-002

Tightening torque:

6 – 8 N·m {52 – 69 in. lbs.}

Tightening torque:

6 – 8 N·m {52 – 69 in. lbs.}

Tightening torque:

6 – 8 N·m {52 – 69 in. lbs.}

Tightening torque:

5 – 7 N·m

{43 – 61 in. lbs.}

Installation of the brake lever

32 mm or more

Installation of the V-BRAKE brake

1. Insert the stopper pin of the brake body into the center

spring hole in the frame mounting boss, and then secure

the brake body to the frame with the link fixing bolt.

2. While holding the shoe against the rim, adjust the

amount of shoe protrusion by changing over the washer

B (thick or thin) so that dimension A is kept at 32 mm or

more.

1 mm

3. While holding the shoe against the rim, tighten the shoe

fixing nut.

B C

B +

C =

2 mm

5 mm Allen key

Shoe fixing pin Shoe fixing pin

Shoe holder

Shoe

5 mm Allen key

Shoe holder

5 mm Allen key

Inner cable lead

Link fixing bolt

Stopper pin

Spring hole

Shoe fixing link

Washer AWasher A

Washer

Shoe fixing nut

Washer B (thin)Washer B (thick)

5. Adjust the balance with the spring tension adjustment

screws.

6. Depress the brake lever about 10 times as far as the grip

and check that everything is operating correctly and that

the shoe clearance is correct before using the brakes.

Spring tension

adjustment screw

Spring tension

adjustment screw

Depress about

10 times

FORWARDR

Replacement of the cartridge shoe

1. Remove the shoe fixing pin, and then slide the shoe

along the groove to remove it from the shoe holder.

3. Insertion of shoe fixing pin is very critical to keep shoe

properly fixed in place.

2. There are two different types of shoe and shoe holder to

be used in the left and right positions respectively. Slide

the new shoes into the grooves on the shoe holders

while taking note of the correct directions and pin hole

positions.

Shoe fixing pin

Shoe

insertion

direction

Front

For the left For the right

Shoe

Front

Multi-Condition Brake System

By providing superior wet weather braking performance

(control and modulation), braking performance will not

vary in a multitude of conditions when using this brake

system.

Use a handlebar grip

with a maximum outer

diameter of 32 mm.

SI-8ED0A-002-00

Product specificaties

Merk:	Shimano
Categorie:	Niet gecategoriseerd
Model:	BL-MX70

Heb je hulp nodig?

Als je hulp nodig hebt met Shimano BL-MX70 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Shimano

Shimano ST-T4000-R Handleiding

15 November 2024

Shimano CLARIS 2400 ST-R240-R Handleiding

30 September 2024

Shimano SL-RV300-7R Handleiding

30 September 2024

Shimano SL-RV400-LN Handleiding

30 September 2024

Shimano SL-RV400-7R Handleiding

30 September 2024

Shimano SW-E8000-L Handleiding

30 September 2024

Shimano CLARIS R2000 ST-RS200-R Handleiding

30 September 2024

Shimano CLARIS 2400 ST-R240-L Handleiding

30 September 2024

Shimano SL-RV300-LN Handleiding

30 September 2024

Shimano SL-RV300-L Handleiding

30 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx 03863 Handleiding

24 December 2024

Vello PGS-P Handleiding

24 December 2024

Venom Quad Charging Station VS4796 Handleiding

24 December 2024

Nec IPJ2000CM Handleiding

24 December 2024

Monogram ZKPN Handleiding

24 December 2024

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024