Sharper Image 20-Setting Beard and Stubble Trimmer Handleiding

Sharper Image Niet gecategoriseerd 20-Setting Beard and Stubble Trimmer

Lees hieronder de 📖 handleiding in het Nederlandse voor Sharper Image 20-Setting Beard and Stubble Trimmer (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
- 1 -
Item No. 205954
20-SETTING BEARD AND STUB BLE TRIMMER
User Guide
Thank you for purchasing the Sharper Image 20-Setting Beard and Stubble Trimmer. Please
read this User’s Guide carefully and keep it for future reference.
TO CHARGE/ RECHARGE
Fully charge Trimmer before using for the first
time or after non-use for a long period of time.
Charging, recharging or using the Trimmer in
temperatures than below 4°C (4F) or higher
35°C (95° F) adversely affects lifespan of the
battery.
• If the Trimmer is subjected to a major change
in temperature, pressure or humidity, let the
trimmer acclimatize for 30 minutes before
using.
• Continuously recharging Trimmer will reduce
lifespan of battery.
1. Be certain Trimmer is OFF (Fig.1).
2. Connect appliance plug directly into the
Trimmer (Fig.2) and plug adapter into any
220-240 V AC outlet. Note: Use only the
included adapter plug provided.
3. The charging light on the adapter lights up
RED to indicate the Trimmer is charging. After
fully charging, the charging light will remain
lit. It will take approximately 10 hours to fully
charge the Trimmer for a cordless trimming
time of up to 45 minutes.
4. Disconnect the cord and unplug from
electrical outlet.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
safety precautions should always be followed,
including the following. Read all instructions
before using this appliance.
To reduce the risk of electric shock:
1. Keep away from water.
2. Do not reach for a plugged in Trimmer that
has fallen into water. Unplug immediately.
3. The Trimmer is for dry use only. Do not use
while bathing or in a shower.
4. Do not place or store Trimmer where it can
fall or be pulled into a tub or sink.
5. Always unplug this Trimmer from the
electrical outlet immediately after (re)
charging.
6. Unplug and remove power supply cord from
Trimmer before cleaning.
FEATURES
1. Trimming Comb
2. Cutting Unit
3. Precision zoom
look adjustment
ring
4. ON/OFF switch
5. Socket for
appliance plug
6. Blade oil
7. Adapter
8. Cleaning brush
- 1 -
OPTIMIZE THE WORKING LIFE OF THE
BATTERY
• After the Trimmer has been charged for
the first time, do not recharge the Trimmer
between trimming sessions. Continue using it
until the battery is completely empty.
• Do not charge for more than 24 hours.
• Do not keep cord permanently plugged in.
• Discharge / run down the battery completely
twice a year by letting the motor run until it
stops.
• If the Trimmer hasn’t been used for a long
period of time, it must be recharged for a full
10 hours.
- 2 -
CORDLESS TRIMMING
1. Unplug Trimmer from outlet and remove
cord.
2. Slide ON/OFF switch ON to begin trimming.
3. When finished, turn Trimmer OFF.
TRIMMING
• Use this Trimmer for its intended household
use as described in this manual.
• Always comb the beard and/or moustache
with a fine comb before you start trimming.
• If you are trimming for the first time, be
careful. Do not move the Trimmer too fast.
Make smooth and gentle movements.
TRIMMING WITH YOUR BEARD
Trimming Comb (Note: Beard Trimming Comb
must be on Trimmer to use the Zoom Lock.)
1. Turn the Zoom Lock to the desired
trimming length setting (See table). The
setting is indicated in the center of the
adjustment ring (Fig. 3). If you are trimming
for the first time, start by using the comb
at the maximum trimming length setting
(#10) to prevent accidentally trimming
hairs too short. As you become familiar with
the settings, adjust Zoom Lock to desired
trimming length. Zoom Lock will click” into
position at each setting.
2. Switch the Trimmer ON.
3. To trim in the most effective way, move
the Trimmer against the direction of hair
growth. Make sure the surface of the comb
always stays in contact with the skin
(Fig. 4).
4. If cut hairs have accumulated in the comb
turn Trimmer off, remove the comb and
shake the hair out of comb (Fig. 5). The
selected trimming length setting will not
change when you do this.
Trimming without the Beard Trimming comb
1. Be certain the Trimmer is in the OFF
position.
Setting Hair length after trimming
- 0.5 mm
1 1 mm
- 1.5 mm
2 2 mm
- 2.5 mm
3 3 mm
- 3.5 mm
4 4 mm
- 4.5 mm
5 5 mm
- 5.5 mm
6 6 mm
- 6.5 mm
7 7 mm
- 7.5 mm
8 8 mm
- 8.5 mm
9 9 mm
- 9.5 mm
10 10 mm
Trimming for ‘Stubble’ Look
5. Be certain Beard Trimmer Comb is on
Trimmer and use setting 1 (3/64in/1mm) to
result in a ‘stubble’ look (Fig. 6).
Trimming without the Beard Trimming comb
Remove comb if you are:
• Defining hair lines
• Trimming nape of neck
• Removing single, unwanted hairs
2. Remove the Beard Trimming Comb by pulling
it off the Trimmer (fig.7)
3. Switch the Trimmer ON.
4. Make well-controlled movements. Touch the
hair/skin lightly with the Trimmer (fig.8).


Product specificaties

Merk: Sharper Image
Categorie: Niet gecategoriseerd
Model: 20-Setting Beard and Stubble Trimmer

Heb je hulp nodig?

Als je hulp nodig hebt met Sharper Image 20-Setting Beard and Stubble Trimmer stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Sharper Image

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd