SentrySafe QAP2BEL Handleiding
SentrySafe
Kluis
QAP2BEL
Lees hieronder de 📖 handleiding in het Nederlandse voor SentrySafe QAP2BEL (19 pagina's) in de categorie Kluis. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/19
XL Quick Access Pistol Safe
Owner’s Manual
QAP2BEL
QAP2E/ QAP2EL
2
Table of ContentsWarnings
WARNING
SentrySafe recommends that you do not store guns in this unit.loaded
NOTICE
YOUR SAFE IS ONLY PART OF YOUR TOTAL SECURITY PROTECTION.
SentrySafe recommends that you store your safe in a closet, office, basement, bedroom or any
other location that is convenient for you but out of direct line of sight from prying eyes.
The location of the safe does not affect the safe’s ability to protect your valuables inside.
This is a California-approved firearm safety device that meets the requirements of Penal Code
section 23655 and the regulations issued thereunder.
1 2 3 4
4
NOTE: Store code and keys in a secure location (other than in the safe).
NOTE: SentrySafe offers a secure on-line location for the entry and retrieval of your code.
Go to and register your safe. www.registermysafe.com
Insert key into keyhole and turn clockwise.
NOTE: Do not lock key inside safe – this is an override key and will
open the safe in the event that you have lost your code.
A Remove the battery pack cover.
B Pull out battery pack (keep battery pack connected
to wires).
C Insert four NEW AA alkaline batteries.
IMPORTANT
All safe models initially work with the factory code 1, 2, 3, 4, 1. It is therefore
important to re-program your safe with a new user code you have personally
selected to provide maximum security.
The XL Quick Access Pistol Safe comes with a built-in code.
Factory code 1, 2, 3, 4, 1.
Press any button once to bring the safe out of standby mode, then
enter the Factory Code 1, 2, 3, 4, 1.
The Green LED will light.
To Program an Electronic Code
A Find the Reset button located behind the battery pack.
B Press and hold the Reset button until the keypad flashes 3 times.
The LEDs remain on to indicate it is ready to accept a new user code.
C Enter a user code that is four, five or six digits long.
D A successful programming of the user code is indicated when the
LED light flashes green three times.
Programming Your Safe
Preparing your safe for first-time use
Programming your safe
Programming Your Safe
NOTE: Do not use rechargeable batteries or any other type of non-alkaline battery.
Do not mix old and new batteries. Do not mix alkaline and standard batteries.
A
Product specificaties
| Merk: | SentrySafe |
| Categorie: | Kluis |
| Model: | QAP2BEL |
Heb je hulp nodig?
Als je hulp nodig hebt met SentrySafe QAP2BEL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kluis SentrySafe
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
Handleiding Kluis
- Kluis Philips
- Kluis Honeywell
- Kluis Abus
- Kluis Avanti
- Kluis Burg-Wachter
- Kluis Dometic
- Kluis Duralock
- Kluis EasySafe
- Kluis Ferm
- Kluis Filex
- Kluis FireKing
- Kluis First Alert
- Kluis Fluke
- Kluis Hama
- Kluis Handson
- Kluis M-Locks
- Kluis Master Lock
- Kluis Nauta
- Kluis Nedis
- Kluis Perel
- Kluis Phoenix
- Kluis Protector
- Kluis Renkforce
- Kluis ROMA
- Kluis Rottner
- Kluis Royal Safe
- Kluis Royal Sovereign
- Kluis Salvus
- Kluis Sentry
- Kluis Sistec
- Kluis SMC
- Kluis Sygonix
- Kluis Technomax
- Kluis Thule
- Kluis Toolland
- Kluis Topcraft
- Kluis Tulox
- Kluis Varo
- Kluis Westfalia
- Kluis Workzone
- Kluis Yale
- Kluis Jewel
- Kluis Juwel
- Kluis Olympia
- Kluis Oxloc
- Kluis First Austria
- Kluis Guzzanti
- Kluis Steren
- Kluis Barska
- Kluis Conrad
- Kluis SereneLife
- Kluis Challenge
- Kluis MSW
- Kluis Hard Head
- Kluis Kidde
- Kluis CAWI
- Kluis Kreator
- Kluis Fichero
- Kluis Kreator-Varo
- Kluis Rottner Tresor
- Kluis Olymp
- Kluis Suncast
- Kluis Winholt
- Kluis Homak Security
- Kluis NOFIRE
- Kluis Stamony
Nieuwste handleidingen voor Kluis
14 December 2024
14 December 2024
6 December 2024
6 December 2024
6 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024