Sennheiser Encore 50 Handleiding

Sennheiser Speaker Encore 50

Lees hieronder de 📖 handleiding in het Nederlandse voor Sennheiser Encore 50 (12 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/12
Floor standing loudspeaker
Page 2
Flat washer x 4
4mm Diameter bolts x 16
Allen key
Large disc x 4
Large conical metal foot x 4
Small conical locking device x 4
Tommy bar
Floor protection disc x 4
Spike x 4
UNPACKING
If you are reading this, you must have already removed the outer carton and split the tape that holds the
main carton together. You have found this instruction manual at the top and hopefully you have not tried to
assemble the speaker before reading this manual. Epos strongly advises you to read it first, before
attempting to assemble the speakers, for your safety and the reliability of the product. Assembling the
speaker is really a two-person job. It is advisable not to start until you have help.
Remove the separate polystyrene packaging and carton boxes from around the speaker, together with the
gift-box that contains the metal feet and bolts. Stand the carton, containing the speaker, on its end. If you
can first discover which end is the bottom, then stand the speaker on its head so the bottom is facing
upwards. Note that the speaker terminal on the rear is at the bottom of the speaker. With the flaps of the
carton open, walk the speaker out of the carton, a little bit at a time, by twisting the speaker from side to
side and pulling it out onto the floor. When it is away from the carton, move the carton away to provide
more space. Lift the top EPE cap from the speaker, untie the cord holding the fabric sleeve and roll it down
to reveal the cabinet. The next step is to fit the plinth.
PLINTH
The Encore 50 floor standing loudspeaker is supplied with a support plinth that serves several purposes.
First, it spreads the footprint of the speaker to reduce the risk of it being accidentally knocked over.
Secondly, the metal feet attached to the plinth help to decouple vibrations and resonances in the speaker
cabinet, when it is working, and dissipate them harmlessly into the floor. It is surprising how much better
loudspeakers sound when properly decoupled to the floor through spiked feet.
The plinth is packed separately in the main carton. Remove the plinth from the packing frames. At this
point you can fit the feet to the plinth. It is advisable to rest the plinth on top of the speaker.
SPIKES
Epos has designed some unique spiked feet for mounting this large loudspeaker that allow a wide range of
adjustment in height and angle. Depending on floor surface (carpet, tiles, wood) the height may be set to
suit the listener and angled up or down, depending on the chosen listening position. It is highly
recommended that you use the feet and the plinth to achieve the maximum performance and flexibility from
the Encore 50 loudspeakers.
ASSEMBLING the PLINTH and SPIKES
Page 3
10mm diameter
fixing Bolt x 4
10mm Washer x 4
Allen key
The plinth should be sitting on the speaker with the Epos logo facing the right way up. Take the metal feet
from the packaging one by one and disassemble them. Place the flat washer into the recess in the top and
pass each of the 4mm diameter bolts through the 4 holes so they exit under the plinth. Take a large conical
metal foot and screw the 4 screws into the foot, one at a time, until it is necessary to use the small ALLEN
key to tighten them completely. This creates a sandwich with the plinth as the filling. Now screw the smaller
conical locking device to the bottom of the spike. Do this to each of the four feet. At this point, the spike
should be as far inside the foot as possible, with only the pointed end sticking out below the locking device.
Repeat this until all four feet are secured to the plinth. Be careful not to scratch yourself on the sharp
spikes. The large discs cover the hole in the top of the washer. They can be fitted at the end of the set-up.
FITTING the PLINTH to the LOUDSPEAKER
Turn the plinth over, so that the feet point upwards. Locate the EPOS logo at the front of the speaker. Four
10mm diameter fixing bolts and washers are supplied in the presentation carton packed within the main
carton. Pass each of the four bolts through the washer and then into the plinth. Line up the four bolts with
the screw inserts in the bottom of the cabinet. Tighten the bolts, using the ALLEN key supplied until the
plinth is tightly secured to the base of the speaker.
SPEAKER LOCATION
It is now time to turn the loudspeakers the correct way up. Take care not to damage your back, the floor, or
the speaker cabinet when inverting it. Remember that you should have some help to do this. It is not a one
person job. Move to approximately the position you want the speakers to be used in, or place them directly
onto the assembled Skateboard.

Product specificaties

Merk: Sennheiser
Categorie: Speaker
Model: Encore 50

Heb je hulp nodig?

Als je hulp nodig hebt met Sennheiser Encore 50 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker Sennheiser

Sennheiser

Sennheiser Encore 50 Handleiding

12 Maart 2023
Sennheiser

Sennheiser TeamConnect Wireless Set Case Handleiding

12 Februari 2023
Sennheiser

Sennheiser SL Loudspeaker 52 A Handleiding

12 Januari 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Kenwood

Kenwood KFC-PS170C Handleiding

3 December 2024
Bose

Bose DesignMax DM5P Handleiding

2 December 2024
Yamaha

Yamaha CHR12 Handleiding

2 December 2024
Yamaha

Yamaha DHR12 Handleiding

2 December 2024
Yamaha

Yamaha DHR15M Handleiding

2 December 2024
Yamaha

Yamaha CHR15M Handleiding

2 December 2024
Yamaha

Yamaha True X Speaker 1A WS-X1A Handleiding

2 December 2024
Yamaha

Yamaha Stagepas 100 Handleiding

2 December 2024
Yamaha

Yamaha NS-2000A Handleiding

2 December 2024
Yamaha

Yamaha DXS15XLF-D Handleiding

2 December 2024