SE Electronics Z5600a II Handleiding

SE Electronics Microfoon Z5600a II

Lees hieronder de 📖 handleiding in het Nederlandse voor SE Electronics Z5600a II (32 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/32

Z5600a II

U s e r M a n u a l

User Manual - EN

Thank you

Thank you for choosing an sE microphone! In addition to some basic safety precautions, this manual includes details

and specifications that we hope will assist you in getting the most out of your Z5600a II. Please take a few minutes to

read through it.

Capturing great audio is our passion. We sincerely hope you’ll enjoy the sound of this mic as much as we enjoyed

designing and building it for you.

Happy Tracking,

The sE Team

Brief Description

The tone quality and versatility of the Z5600a II make it an asset to any mic locker. -This large diaphragm condenser

microphone has nine switchable polar patterns, ranging from omnidirectional to cardioid to figure-8, with six additional

patterns in between. Central to the Z5600a II’s rich timbre is a 12AX7 tube, delivering stunning detail and flattering the

source with enhanced harmonic character. In other words, this mic sounds huge! It has been praised for capturing

incredible vocal tones, but the Z5600a II is engineered to excel in any sonic context.

The Z5600a II is equipped with a switchable low cut filter, as well as a switchable -10dB pad, making it just as suitable

for recording a string quartet, or drum overheads, as it is for tracking vocals.

Like all of our microphones, the Z5600a II is built by hand at sE Headquarters in Shanghai. We take pride in the attention

to detail under which our products are crafted, therefore the entirety of manufacturing is done in our own facilities. We

also individually test and measure the tubes for these mics to ensure optimal performance upon arrival.

What’s in the box

Your Z5600a II includes a custom flight case to safely transport the microphone and its necessary accessories. If

anything is missing, please contact your sE Electronics dealer f or assistance.

• Z5600a II microphone

• 8- pin microphone cable

• Custom shockmount

• Power supply

• IEC power cable

Controls

The Z5600a II -features both an Attenuation Switch and a Low Cut Switch.

Attenuation Switch

The Attenuation Switch is located on the front-left side of the microphone. When engaged, the

incoming signal is reduced by 10dB, helping prevent signal distortion preamplifier clipping and

when capturing audio at close proximity and/or high sound pressure levels.

Low-Cut Switch

The Low-Cut Switch is located on the front a low-right side of the microphone, inserting -cut filter

at 5 . 0Hz when engaged When switched to the left, the filter is removed for a flat frequency

response. This low-cut switch is useful for reducing plosives, footfall noise, and especially rumble

that might adversely affect the recorded signal. Additionally, the -low cut filter will help minimize

the proximity effect when “close-miking,” i.e. placing the microphone a very short distance from

the source.

Pattern Switch

The Pattern Switch is located front and center on the microphone’s power supply. This 9-

position switch allows a range of polar patterns from omnidirectional (left,) to cardioid (middle,)

to figure 8 (right.) There are six pattern variations available between these three. This array of

patterns makes it possible to tailor the balance of direct sound, versus ambient sound, that the

microphone picks up.

Powering

The included floor box contains the outboard power supply for the Z5600a II. No phantom power is required from an

interface or microphone preamplifier.

Before powering on, connect all required cables (IEC to power, XLR to preamplifier or interface, and 8-pin cable from

floor box to microphone). Then turn the power on via the switch on the back of the Z5600a II floor box.

For best performance, we recommend allowing approximately 15 minutes of “warm up” time before recording. This

allows the tubes within the Z5600a II to heat up and stabilize, and reduces the risk of unwanted noise or distortion on

your recordings.

Risk of damage

Do not connect the microphone to any power supply other than the included Z5600a II power

supply. Do not apply phantom voltage (+48VDC) from an external interface or preamplifier.

This is the only way to ensure safe and reliable operation.

Safety and maintenance

Risk of damage

Please make sure that the piece of equipment to which your microphone and PSU will be

connected fulfils the safety regulations enforced in your country and is fitted with a ground

lead.

Cleaning icroph the m one

The microphone d in the supplied should only be cleaned with a dry, soft cloth. It is best store wooden presentation box.

Product specificaties

Merk:	SE Electronics
Categorie:	Microfoon
Model:	Z5600a II
Kleur van het product:	Grey, Stainless steel
Soort:	Microfoon voor studio's
Type verpakking:	Doos
Connectiviteitstechnologie:	Bedraad
Opbergetui:	Ja
Aansluiting:	XLR (8-pin)
Verpakkingsinhoud:	12AX7/ECC83
Microphone direction type:	Cardioïde/omnidirectionele microfoon
Vermogenstoevoer inclusief:	Ja
Diafragmamateriaal:	Goud/Mylar
Gevoeligheid microfoon:	-32 dB
Spreekspoel types:	Condensor
Frequentie microfoon:	20 - 20000 Hz
Microphone input impedance:	200 Ohm
Aantal producten inbegrepen:	1 stuk(s)
Gewicht microfoon:	850 g
Microfoon Signal-to-Noise Ratio (SNR):	81 dB
Gevoeligheid (1 kHz):	25.12 mV/Pa
Eigenruis:	13 dB
Membraan diameter:	35 mm
Microphone Total Harmonic Distortion (THD):	0.5 procent
Voordempkussen:	-10 dB
Doorlaatfilterschakelaar:	50 Hz
Stroomtoevoer gewicht:	1970 g