Scott Genius 900 AXS Handleiding

Scott Fiets Genius 900 AXS

Lees hieronder de 📖 handleiding in het Nederlandse voor Scott Genius 900 AXS (20 pagina's) in de categorie Fiets. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/20
W W W . S C O T T - S P O R T S . C O M
WWW.SCOTT-SPORTS.COM
SCOTT Sports SA
Route du Crochet 17, CH–1762 Givisiez
Phone: +41 26 460 16 16 | Fax: +41 26 460 16 00
Email: scottsupport@scott-sports.com
All rights reserved © 2017 SCOTT Sports SA
Distribution:
SSG (Europe) Distribution Center SA, P.E.D. Zone C1, Rue du Kiell 60, 6790 Aubange, Belgium
v7.0/03072017
USER MANUAL
SCOTT GENIUS
WWW.SCOTT-SPORTS.COM
ENGLISHENGLISH
Genius Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04
Geometry/Technical Data Genius 27.5" & 29" . . . . . . . . . . . . . . . . . 05
TWINLOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06
B S Up of Shock & Fasic et- orks. . . . . . . . . . . . . . . . . . . . . . . . . . .07
SAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
R Shock S Upebound et- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09
R Rear Deplaceable ropout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
P Mivot aintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
C Rable outing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
BB Standards/FD Mounting Details . . . . . . . . . . . . . . . . . . . . . . . . 17
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Guarantee on SCOTT Bikes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
•CONTENTS
The SCOTT Genius should be adjusted exactly to the individual
rider to achieve maximum saftey and fun while riding.
SCOTT recommends that all adjustments be carried out by
your local authorized SCOTT dealer. Some basic maintenance
can be done if strictly following the manuals supplied with
this bike.
Please contact your authorized SCOTT dealer for advice in order
to avoid any harm and assist you with any questions or technical
problems.
03 |
BI KE USER MANUAL | GENIUSGENIUS | BIKE USER MANUAL
| 02
S / 900 S / 700 M / 900 M / 700 L / 900 L / 700 XL / 900 XL / 700
LOW BB Setting HIGH BB Setting LOW BB Setting HIGH BB Setting LOW BB Setting HIGH BB Setting LOW BB Setting HIGH BB Setting
A HEAD TUBE ANGLE 65.0 ° 65.6 ° 65.0 ° 65.6 ° 65.0 ° 65.6 ° 65.0 ° 65.6 °
B HEAD TUBE LENGTH 95.0 mm 3.7 in 95.0 mm 3.7 in 95.0 mm 3.7 in 95.0 mm 3.7 in 4.3 in 4.3 in 4.9 in 4.9 in110.0 mm 110.0 mm 125.0 mm 125.0 mm
CTOP TUBE
HORIZONTAL 569.7 mm 22.4 in 568.2 mm 22.4 in 602.8 mm 23.7 in 601.2 mm 23.7 in 631.8 mm633.4 mm 24.9 in 24.9 in 670.1 mm 26.4 in 668.4 mm 26.3 in
D STANDOVER HEIGHT
E BB OFFSET -1.1 in-27.4 mm -20.0 mm -20.0 mm -20.0 mm -20.0 mm-0.8 in -1.1 in-27.5 mm -0.8 in -1.1 in-27.6 mm -0.8 in -1.1 in-27.8 mm -0.8 in
F BB HEIGHT 346.1 mm 13.6 in 13.4 in 346.0 mm 13.6 in340.0 mm 340.0 mm 340.0 mm 340.0 mm13.4 in 345.9 mm 13.6 in 13.4 in 345.7 mm 13.6 in 13.4 in
G WHEEL BASE 1,165.9 mm 45.9 in 1,164.6 mm 45.9 in 1,198.9 mm 1,197.6 mm 1,232.1 mm47.2 in 47.1 in 48.5 in 48.5 in1,230.8 mm 1,271.3 mm 50.1 in 50.0 in1,270.0 mm
HBB CENTER TO
TOPTUBE CENTER
IBB CENTER TO TOP OF
SEATTUBE 410.0 mm 410.0 mm 440.0 mm 440.0 mm 480.0 mm 480.0 mm 520.0 mm 520.0 mm16.1 in 16.1 in 17.3 in 17.3 in 18.9 in 18.9 in 20.5 in 20.5 in
J SEAT ANGLE 74.7 ° 75.3 ° 75.3 ° 75.3 ° 75.3 °74.7 ° 74.8 ° 74.8 °
K CHAINSTAY 438.0 mm 436.0 mm 438.0 mm 436.0 mm 438.0 mm 436.0 mm 438.0 mm 436.0 mm17.2 in 17.2 in 17.2 in 17.2 in 17.2 in 17.2 in 17.2 in 17.2 in
L REACH 405.9 mm 16.0 in 16.2 in 439.1 mm412.0 mm 17.3 in 445.0 mm 17.5 in 466.1 mm 18.4 in 18.6 in 499.2 mm 19.7 in 505.0 mm 19.9 in472.0 mm
M STACK 599.7 mm 23.6 in 595.5 mm 23.4 in 599.9 mm 23.6 in 595.5 mm 23.4 in 613.7 mm 609.2 mm 622.8 mm24.2 in 24.0 in 24.7 in627.5 mm 24.5 in
N STEM LENGTH 40.0 mm 1.6 in 1.6 in 2.0 in 2.0 in 2.0 in 2.0 in 2.0 in 2.0 in40.0 mm 50.0 mm 50.0 mm 50.0 mm 50.0 mm 50.0 mm 50.0 mm
0 TRAIL 117.7 mm 4.6 in 4.2 in 4.6 in 4.2 in 4.6 in 4.2 in107.3 mm 117.6 mm 107.3 mm 117.5 mm 107.3 mm 117.4 mm 4.6 in 4.2 in107.3 mm
ENGLI SHENGLI SH
•GENIUS CONCEPT
The Genius has been a longstanding staple in our range of Mountain Bikes for many years
now. Having always been the result of a focus on innovation, technology and design, the
Genius has evolved over the years in order to be able to tame anything that comes its way.
With the latest iteration of our all mountain trail bike, one concept formed the backbone of
the development process. What comes down, must go up. This has always been the premise
of the Genius, it truly is the perfect MTB for every trail it encounters.
Steep rooty climbs? No problem.
Fast, flowy single track? Yes please.
2000m long descents in the alps? Music to our ears.
With the Genius, no matter the trail, no matter the conditions, no matter the rider, it is always
the right tool for the job.
•GEOMETRY/TECHNICAL DATA GENIUS 27.5" & 29"
Seatpost diameter 31.6mm
Seatube clamp 34.9mm
Headset Semi integrated cups 56mm
bottom/44mm top
BB housing PF92
Front derailleur Shimano high direct side swing (N/A on
HMX frames) additional parts needed
Chainring size 36T max
Shock Dimensions 185x55mm
Shock mount size 30x8mm
Max tire width 27.5 plus /2.8 tire (71mm)
29 / 2.6 tire (66mm)
Please note:
Tire sizes often vary from brand to brand.
Ensure the tire clearance is adequate
when replacing your tires!
05 |
BI KE USER MANUA L | GENIUSGENIUS | BIKE USER MANUAL
| 04
ENGLISHENGLISH
•IMPORTANT!
SCOTT Genius is designed around the BOOST platform so many of the fitted parts:
cranks/wheels/dropouts/forks differ from traditional cycle parts. Always consult your
authorized SCOTT dealer for advice on replacing or repairing any part of your SCOTT bike!
•TWINLOC
The TWINLOC system offers simultaneous control of the front and rear shocks with a single
lever allowing the ride of the bike to be adjusted at the flick of a finger.
The 3 basic functions of TWINLOC system are:
-Climb-out Mode: Climb rear / climb front
-Traction Mode: Traction mode rear / platform mode front (where applicable)
-Descent Mode: Full travel rear / full travel front
You can only assemble the “standard” TWINLOC remote lever in “left side upward position”
on the handlebar (this is usually fitted on bikes with x2 front chainrings.)
On bikes with p4-x1 chainring on the front the under bar TWINLOC remote lever in “left side
downward” position can be fitted as standard.
It is possible to change the TWINLOC lever to the underbar option if the bikes gears have
been changed to p4-x1 system, a new alternative lever will be required for this adjustment;
please consult your local SCOTT dealer for more information on obtaining the correct lever
for your bike.
There are 3 positions of the TWINLOC remote lever.
1. CLIMB MODE:
The shock is nearly locked; climbing on asphalt roads is now possible with little power loss.
A simultaneous blow-off-system prevents the shock being damaged in case the rider does
not open the system while crossing obstacles.
2. TRACTION MODE:
By reducing the internal chamber volume inside the shock the travel of the shock will
be reduced, the characteristic of the air spring gets harder this results in climbing with
reduced “bobbing” and offers still optimum traction of the rear wheel.
3. DESCENT MODE:
Full travel of the front and rear shocks.
You will find the following positions on the remote lever:
•BASIC SET-UP OF SHOCK & FORKS
Recommended tools for the shock setup:
-The SAG tool that came with your bike.
-A shock pump with a dial up to 20bars/300psi with a special air valve connector (not
supplied with this bike), this will help stop air from escaping while removing the pump
from the shock valve.
Please note that air will flow into the hose and indicator when counterchecking the air
pressure, this will give the appearance that the shock has less air pressure then it was setup,
your shock may need to be adjusted once this action is made.
Please also note that the indicators of shock pumps have a tolerance of max. 10%.
For bikes spec’d with Fox shock and forks:
You can find more specific information about Fox set up on Fox’s website, please use your
fork/shock ID number to find more useful setup tips for your exact fork and shock (please
visit: ridefox.com)
07 |
BI KE USER MANUAL | GENIUSGENIUS | BIKE USER MANUAL
| 06
ENGLISHENGLISH
•SAG
Your SCOTT bike will be supplied with a SAG tool to help set up your bikes suspension, these
SAG tools can be easily clipped on the shock body and fork dust seal.
For the best performance it is recommended you start with SAG of 25-30% for shocks and
15-20% for forks.
1. Make sure before any adjustment is made that your shock and forks are in the “open”
position.
2. With the shock pump attached to the rear shock valve, pump your desired pressure
into the shock. Once the pressure is achieved slowly compress and decompress your
shock through 25% of its travel 10 times. This will equalize the positive and negative air
chambers and will change the pressure on the pump gauge, if needed add or reduce
pressure and repeat.
Note the compression/decompression of the rear shock through the travel must also
be done if the pressure is reduced!
The same operation is used on the forks.
3. Once your desired pressure is reached slide the rubber O-ring on the shock and fork leg
against the dust seal, clip on your SAG tool if required.
4. Sit on your bike in your usual riding position (in your riding gear: if you carry a bag/
Hydration-system put it on,) don’t “bounce” the suspension while doing this, use a wall or
a friend for support if needed.
5. Get off the bike gently without bouncing and check the O-ring position on the shaft or
the fork stanchion, with the SAG adjuster clipped on. This makes it easy to see where your
SAG is set.
•IMPORTANT!
Do not sit on your bike with the shock pump attached to the bike!
•REBOUND SHOCK SET-UP
“Rebound” describes the speed the shock returns back to its original length after absorbing
an obstacle, setting of this is very important for the handling and correct function of the bike.
The rebound adjustment lever can be found on the head of the shock
After the shock pressure/sag is correctly set ride your bike in a safe area with your riding
gear/backpack, etc. While remaining in the saddle, ride you bike off a drop/kerb of about
10-15 cm.
-If it bounces 1-2 times and settles the set-up is good.
-If it bounces more than 3 times the rebound is too fast, turn the knob 1-2 “clicks”
clockwise and repeat.
-If there is no bounce the rebound is too slow, turn the knob 1-2 click counter clockwise
and repeat.
-Repeat these steps until the desired result is achieved.
Your SCOTT Genius bike was designed to be used in conjunction with a specific shock and
forks, changing the shock or forks on your bike may cause poor/unsafe riding characteristics
or damage to frame and components, please consult your SCOTT dealer for any assistance
you need, failure to do this may affect your warranty
* Fox Nude model shown
09 |
BI KE USER MANUAL | GENIUSGENIUS | BIKE USER MANUAL
| 08
ENGLISHENGLISH
•REPLACEABLE REAR DROPOUT
On SCOTT Genius models for 2018 the rear derailleur hanger is replaceable, depending on
your model of Genius there are 5 different hangers available, 2 for carbon swingarms SCOTT
and 3 alloy swingarms, these parts can be seen below, please consult your SCOTT dealer for
information on the correct part.
FOR CARBON SWINGARMS ONLY:
Sram and non-direct mount
derailleurs
SCOTT part number 254090
Shimano direct mount
derailleurs
SCOTT part number 254091
Sram and non-direct
mount derailleurs
SCOTT part
number 254092
Non-Direct mount derailleurs
and boost Q/R wheels
SCOTT part number 254094
Shimano direct mount
derailleurs
SCOTT part
number 251093
FOR ALLOY SWINGARMS ONLY:
If your dropout needs to be replaced, we recommend this work should be carried out by
your local dealer as the rear derailleur may need adjustment, failure to adjust this SCOTT
correctly may result in accident or damage to your bike.
•IMPORTANT!
We recommend all work should be carried out by your authorised SCOTT dealer!
If you wish to change this item yourself, please ensure the bike is supported correctly to
prevent damage by referring to the general manual instructions supplied with your bike.
Before installing the new hanger first
make sure the area is clean; insert
the hanger.
Insert the end cap through the frame and
into the hanger.
Make sure the location arrow is pointing
to the lower bolt hole; insert the bolt (Max
torque 1.5 N/M)
Insert the second bolt in the rear of the
dropout (Max torque 1.5 N/M)
(Carbon swingarm fitting shown)
Once the bike is reassembled please ensure the wheels are refitted correctly and the gears
are set correctly including the over shift stops, please consult your authorized SCOTT dealer
for assistance.
11 |
BI KE USER MANUAL | GENIUSGENIUS | BIKE USER MANUAL
| 10
ENGLISHENGLISH
•PIVOT MAINTENANCE
The pivot and bearings on the Genius are easy to mSCOTT aintain.
If you have to change the bearings or pivots please consult your local dealer for the SCOTT
purchase and fitting of the kit as special tools are required for disassembly and reassembly.
To prolong the life of your pivot bearings an external treatment with water repellent after
every bike wash will help repel excess water. We do not recommend heavy grease sprays
since these will leave a film on the parts which are difficult to remove. We recommend the
same for the chain also after washing and before chain lube.
•IMPORTANT
Do not let spray or oils come into contact with the disc brake pads or rotor!
Please refer to the manuals supplied with this bike for wash and care instructions for your
SCOTT bike.
•WHEELS
The SCOTT Genius frame is incredibly versatile with the option to change your wheel size
from 29" to 27.5" and 27.5" plus with minimal effort, to do this the following tire sizes must be
observed:
-27.5 plus / 2.8" (71mm) tire
-29 / 2.6" (66mm) tire
Even when following these tire sizes you must always double check the clearance as tire
sizes may vary with different brands.
The SCOTT Genius is equipped with a Geometry chip, this can be altered if you wish to
adjust the geometry on your Genius to tune the handling of yoSCOTT ur bike.
•CABLE ROUTING
On the Genius the cable guides on the headtube can be changed if required so SCOTT
different cable configurations can be used.
The main cover plate of the cable guide is available in two options:
-HT-Blank: this can be used when no cables are to be routed.
-HT: this is open and can be used for different cable options.
If cables are to be routed you must select the correct insert for the cover depending on the
configuration you require, the inserts can be easily changed in cover plate once the cables
have been removed and the cover removed from the bike.
If the bike is equipped with small 27.5" tires and set in the "Low mode" crank clearance
must be checked before riding!
“Low mode” for 29 “High mode” for 29" and 27." tires. 5 tires.
Please ensure the geo chip is in the same position for both the left and right sides.
•IMPORTANT
While the Genius frame is compatible with different wheel sizes this does not SCOTT
mean the fork fitted will be compatible, please check with your local SCOTT dealer if
there are any compatibility/clearance questions before carrying out any wheel changes.
As with all parts on your bike please ensure all bolts are set to the correct torque SCOTT
and threadloc used where applicable/ geo chip bolt 10 N/M and 242 (medium strength)
threadloc.
13 |
BI KE USER MANUAL | GENIUSGENIUS | BIKE USER MANUAL
| 12

Product specificaties

Merk: Scott
Categorie: Fiets
Model: Genius 900 AXS

Heb je hulp nodig?

Als je hulp nodig hebt met Scott Genius 900 AXS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Fiets Scott

Scott

Scott Speedster 60 Handleiding

26 Februari 2025
Scott

Scott Addict eRIDE 10 Handleiding

15 November 2024
Scott

Scott Genius 950 Handleiding

7 Augustus 2024
Scott

Scott Addict Handleiding

3 April 2024
Scott

Scott Contessa Voltage eRIDE 900 Handleiding

3 April 2024
Scott

Scott Voltage eRIDE 900 SL Handleiding

3 April 2024
Scott

Scott Contessa Solace eRIDE 15 Handleiding

3 April 2024
Scott

Scott Voltage eRIDE 900 Handleiding

3 April 2024
Scott

Scott Voltage eRIDE 910 Handleiding

3 April 2024
Scott

Scott Speedster 40 EQ Handleiding

3 April 2024

Handleiding Fiets

Nieuwste handleidingen voor Fiets

Athletic

Athletic Vision 240BH Handleiding

2 April 2025
BodyCraft

BodyCraft SPX-MAG Handleiding

27 Maart 2025
QU-AX

QU-AX Luxus Handleiding

13 Januari 2025
Chipolino

Chipolino Marathon Handleiding

5 December 2024
Marvel

Marvel Avengers Handleiding

18 November 2024
Amigo

Amigo E-Vibe S2+ Handleiding

17 November 2024
VANMOOF

VANMOOF X2 Handleiding

15 November 2024
Kawasaki

Kawasaki Z800 (2012) Handleiding

15 November 2024
Trek

Trek Fuel EXe 9.8 XT Handleiding

14 November 2024
Kindercraft

Kindercraft RAPID 2 Handleiding

23 Oktober 2024