Sauter HBA 100-0 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Sauter HBA 100-0 (7 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7
Sauter GmbH
Ziegelei 1
D-72336 Balingen
e-mail: info@kern-sohn.com
Phone : +49-[0]7433- 9933-0
Fax: +49-[0]7433- - 9933 149
Internet: www.sauter.eu
Instruction manual analog shore
hardness tester
SAUTER (&TI) HB
Version 2.0
03/2020
GB
HB- -e-2020 BA
PROFESSIONAL MEASURING
2 - -e-2020 HB BA
GB
Thank you for purchasing the analogue Shore hardness tester from SAUTER. We
hope you will be very satised with the high quality of the hardness tester and its
functionality. For any questions, wishes and suggestions we are at your disposal.
Table of contents:
1 Before commissioning .................................................................................. 3
2 General overview ........................................................................................... 3
3 Technical data ................................................................................................ 4
4 Measurement method .................................................................................... 4
5 Storage ........................................................................................................... 4
6 SHORE DUROMETER TEST STAND with HB .............................................. 5
7 Introduction .................................................................................................... 5
8 Structure ......................................................................................................... 5
9 Operation ........................................................................................................ 6
10 Note ................................................................................................................. 7
11 Maintenance ................................................................................................... 7
HB- -e-2020 3 BA
1 Before commissioning
Before putting the device into operation, check the delivery for any transport damage
to the packaging, the plastic case and the device itself. Should this be the case,
SAUTER must be contacted immediately.
2 General overview
The hardness of plastic is generally measured with a Shore hardness tester, using
either the or the scale. This is the preferred method for rubber or Shore A Shore D
elastomers and also for "softer" plastics such as polyolens, uoropolymers and vinyl.
The Shore A scale is used for "softer" rubbers and the Shore D scale for the "harder"
rubbers.
Shore C/ Shore 0 is mainly used for tests with foam rubber, sponges, microporous
plastic, etc.
These three dierent tips (see gure above) are not interchangeable. For each
hardness range the corresponding Shore hardness tester must be purchased.
Developed according to the following standards:
DIN 53505
ASTM D2240
ISO 868
This Shore hardness tester is especially recommended for internal comparison
measurements. Standard calibrations, e.g. to DIN 53505, are often not possible due to
very tightly specied standard tolerances and are therefore not oered by SAUTER.
Shore A, Shore C / Shore 0 and Shore D


Product specificaties

Merk: Sauter
Categorie: Meetapparatuur
Model: HBA 100-0

Heb je hulp nodig?

Als je hulp nodig hebt met Sauter HBA 100-0 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Meetapparatuur Sauter

Sauter

Sauter FC 10 Handleiding

5 Februari 2025
Sauter

Sauter FH 20 Handleiding

5 Februari 2025
Sauter

Sauter FL 5K Handleiding

5 Februari 2025
Sauter

Sauter LB 500-2 Handleiding

27 Januari 2025
Sauter

Sauter TVL Handleiding

27 Januari 2025
Sauter

Sauter JCT 100 Handleiding

27 Januari 2025
Sauter

Sauter LB 300-2 Handleiding

27 Januari 2025
Sauter

Sauter TI-HEA Handleiding

27 Januari 2025
Sauter

Sauter JCS 200 Handleiding

27 Januari 2025

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur