Sauter FL 5 Handleiding

Sauter Niet gecategoriseerd FL 5

Lees hieronder de đź“– handleiding in het Nederlandse voor Sauter FL 5 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 60 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
Sauter GmbH
Ziegelei 1
D-72336 Balingen
E-Mail: info@sauter.eu
Tel: +49-[0]7433- -199 9933
Fax: +49-[0]7433- -149 9933
Internet: www.kern-sohn.com
Instruction Manual
FL
FL- -e-1411 1BA
Table of Contents
1. Introduction
2. Before Use
3. Operation Overview
4. Powering the FL
5. Battery Indicator
6. Fitting Accessories
7. Mounting to a Test Stand
8. Powering up
9. Basic Functions
10. Main Menus
AUTO-OFF
PASS-FAIL
MEMORY
CALIBRATION
DIAGNOSTIC
ABOUT
11. Measurement Practice
12. FL Specications
13. Conversion Factor
14. Declaration of Conformity
1. Introduction
Thank you for choosing the SAUTER FL series instrument.
With correct use and regular re-calibration it will give many
years of accurate and reliable service.
The FL can measure tensile and compressive forces
accurately, being simply used by the operator. It may be
used handheld or mounted a xture or test stand. on
SAUTER oers software and accessories to make the
force gauge even more versatile. Ask your SAUTER
distributor for additional information or visit our website at
www.kern-sohn.com
2. Before Use
After having receiv the unit please check that no ed
physical damage has occurred to the packaging material,
plastic case or the instrument itself. If any damage is
evident, please notify SAUTER immediately.
3. Operation Overview
The most common used features (such as displaying
force, peak hold, zero and changing of displayed units) can
all be done by pressing a single dedicated key identied on
the front panel-see the Basic Functions section.
You can press a menu key to access the gauge
conguration- see the Main Menu section.
4. Powering the FL
The FL is supplied with a set of 4 Nickel Metal Hydride AA
rechargeable batteries. For safety reasons during
transportation the batteries are shipped discharged. To
obtain maximum battery life we recommend that you
charge them with the charger/adaptor supplied for at least
14-16 hours when you rst receive the instrument.
5. Battery Indicator
If battery level is less than 3.9 V, The “battery empty”
message will be displayed and the gauge will power down
automatically.
Important: Only use the adaptor/charger supplied
6. Fitting Accessories
Couple ttings directly to the load cell stem or use an
extension rod. The threads are and have capacities up M6
to 2500 N.
Ensure that the xing does nor contact the force gauge
case. Ensure that anything coupled to the gauge is
screwed finger-tight only. Excessive torque can damage
the load cell and is not covered by warranty.
7. Mounting to a Fixture or Test Stand
The two 10-32 threaded holes, or fours thread holes on M3
the rear of the gauge can be used for mounting the gauge.
A versatile stand mounting plate is available to couple the
force gauge to many brands of test stands.
8. Powering up
As shown in Figure 1 the control panel has eight keys.
Sauter GmbH
Ziegelei 1
D-72336 Balingen
E-Mail: info@sauter.eu
Tel: +49-[0]7433- -199 9933
Fax: +49-[0]7433- -149 9933
Internet: www.kern-sohn.com
Instruction Manual
FL
FL- -e-1411 2BA
Figure 1
As shown in Figure 1 the control panel has eight keys.
To power up the gauge, the ON/OFF key has to be
pressed. A short self-test runs during which the display will
show the capacity in Newton.
After the self test, providing no load has been applied to
the instrument, the display will show all zeroes. This is
because the gauge re-zeroes itself during the self-test
routine.
*If a force is applied via the load cell sensor (hole at the
bottom of the ), the reading on display will register the FL
applied force.
*Forces may not show zero if it is moved during the self
test routine. Once it is properly mounted and zeroed the
reading will be stable.
*Do not overload the load sensor. This will cause
irreparable damage. Forces greater than 120% of full-scale
will produce an audible beep and OL symbol will blink on
the display until load is release and RESET key is pressed.
To power down the gauge press the ON/OFF key.
*All the current settings are saved when the gauge is
turned o and the gauge will function in the same mode
when powered up again.
9. Basic Functions
Tensile forces are displayed on the and recognized by FL
the symbol. Compressive forces are displayed on the FL
and recognized by the symbol.
Display of Tension/Compression
A load indicator bar alerts the operator to how much load
has been applied to the load sensor.
For tensile force the indicator bar is moving from right to
left. For compressive forces the indicator bar is moving
from left to right.
Zeroing the gauge
During the operation of the gauge it is often necessary to
zero the display e.g. when you wish to tare out the –
weight of a grip, so it does not become part of the
measured reading. Press and release the ZERO key.
Changing the unit of measurement
You can choose the following units of measurement
depending on the capacity of your gauge:
milliNewtons, kiloNewtons, Newtons, gram-force, kilogram-
force, ounceforce or pound-force.
To change the display units, press the UNIT key. Each
successive key press will select the next available units ed
until the gauge returns to its original setting. The FL
automatically converts readings as new unit of a
measurement is selected.
*Note: All units may not be displayed depending on the
capacity of the gauge.
Changing the mode of measurement
You can choose the following modes of measurement:
Track, Peak-Tension, and Peak-Compression, to change
the display mode press MODE key. Each successive key
press will select the next available modes until the ed
gauge returns to its original setting.
Track mode
Press MODE key until the appeared on the display. The
display will now indicate forces applied in both directions
as they are applied to the load sensor and maintain the live
display. See Figure 3a
Peak-Tension mode
Sauter GmbH
Ziegelei 1
D-72336 Balingen
E-Mail: info@sauter.eu
Tel: +49-[0]7433- -199 9933
Fax: +49-[0]7433- -149 9933
Internet: www.kern-sohn.com
Instruction Manual
FL
FL- -e-1411 3BA
Press MODE key until the appears on the
display. The display will show the maximum tensile force.
See Figure 3b
Peak-Compression mode
Press MODES key until s on the appear
display. The display will show the maximum compressive
force. See Figure 3c
Resetting the gauge
Press RESET key to clear both maximum registers and
prepare for detecting the next maximum readings.
Backli t Display gh
If any key is pressed or forces applied to the load are
sensor bigger than 0.5 % of full scale, the backlight be
activated for 60 seconds.
Saved reading to memory
Any reading can be saved anytime by pressing
MEM/ENTER key. A total of 500 readings can be stored in
the database included the reading unit.
Computer Control of Force Gauge
A computer can control the force gauge by sending RS-
232 commands.
RS232 output signal
The displayed reading may be transmitted to PC by
pressing the PRINT key or sending request command from
PC to the gauge.
10. Main Menu
Press MENU/ESC key to access the main menu. To move
between the option listed on the main menu page, press
UP and DOWN arrow keys to move the cursor. Press
ENTER to select the sub-menus, activate feature and
enter values. Within sub-menus UP, DOWN, LEFT and
RIGHT arrow keys will also change numerical values.
Press ESC to return to the main menu page.
Figure 4
1) AUTO-OFF
Press the MENU key, the display will show the main menu
page and use UP and DOWN to move the cursor point to
AUTO-OFF.
Press the ENTER key. The display will show the Auto-o
menu page.
Press ESC key to return to the main menu page.
An Auto-o feature can be enabled to conserve battery
power where the gauge powers down after 5,10 and 15
minutes (depending on Auto-o time) since the last key
has been press . The will appear in the main display ed AO
if you activate this feature.
Figure 5

Product specificaties

Merk: Sauter
Categorie: Niet gecategoriseerd
Model: FL 5

Heb je hulp nodig?

Als je hulp nodig hebt met Sauter FL 5 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Sauter

Sauter

Sauter FK 10 Handleiding

3 Juni 2023
Sauter

Sauter FA 200 Handleiding

14 Mei 2023
Sauter

Sauter FK 500 Handleiding

10 Mei 2023
Sauter

Sauter FK 1K Handleiding

8 Mei 2023
Sauter

Sauter FA 10 Handleiding

27 April 2023
Sauter

Sauter FL 200 Handleiding

27 April 2023
Sauter

Sauter FL 500 Handleiding

26 April 2023
Sauter

Sauter FL 100 Handleiding

25 April 2023
Sauter

Sauter FL 50 Handleiding

20 April 2023
Sauter

Sauter FK 100 Handleiding

19 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Smeg

Smeg GTA-6 Handleiding

21 November 2024
Smeg

Smeg KIT6CX Handleiding

21 November 2024
Senal

Senal SCS-98 Handleiding

21 November 2024
Senal

Senal ASM-6 Handleiding

21 November 2024
Senal

Senal ASM-MNTKIT Handleiding

21 November 2024
Senal

Senal SMS-45 Handleiding

21 November 2024
Smeg

Smeg KIT6PX Handleiding

21 November 2024
Senal

Senal SCI-3212MP Handleiding

21 November 2024
Matterport

Matterport Pro2 3D Camera MC250 Handleiding

21 November 2024
Senal

Senal OLM-2S-P Handleiding

21 November 2024