Samson Graphite M25 Handleiding
Samson
Midi-keyboard
Graphite M25
Lees hieronder de 📖 handleiding in het Nederlandse voor Samson Graphite M25 (52 pagina's) in de categorie Midi-keyboard. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/52

Quick Start Guide

2
Copyright 2015
V2
Samson Technologies
45 Gilpin Avenue
Hauppauge, New York 11788-8816
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 631-784-2201
www.samsontech.com
Apple, Mac, Mac OS, and iPad are trademarks of Apple Inc., registered in the U.S. and other
countries.
IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used
under license.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER SER-
VICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the
user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance instructions in the literature accompanying the appli-
ance.
ATTENTION
RISQUE D’ÉLECTROCUTION !
NE PAS OUVRIR !
WARNING
TO PREVENT FIRE OR SHOCK HAZARD. DO NOT USE THIS PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED
TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRICAL SHOCK, MATCH WIDE
BLADE PLUG TO WIDE SLOT AND FULLY INSERT.

Graphite M25 · USB Keyboard Controller
3
ENGLISHFRANÇAISDEUTSCHEESPAÑOLITALIANO
CAUTION
Any changes or modifications to the construction of this device which are not expressly ap-
proved by the party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
If you want to dispose this product, do not mix it with general household waste. There
is a separate collection system for used electronic products in accordance with legisla-
tion that requires proper treatment, recovery and recycling.
Private household in the 28 member states of the EU, in Switzerland and Norway may return
their used electronic products free of charge to designated collection facilities or to a retailer (if
you purchase a similar new one).
For Countries not mentioned above, please contact your local authorities for a correct method of
disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, re-
covery and recycling and thus prevent potential negative effects on the environment and human
health.

4
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. -Do not install near any heat sources such as radiators, heat registers, stoves, or other appa
ratus (including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the man-
ufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
11. Unplug the apparatus during lightning storms, or when unused for long
periods of time.
12. Refer all servicing to qualified personnel. Service is required when the apparatus has
been damaged in any way, such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
13. This appliance shall not be exposed to dripping or splashing water and that no object filled
with liquid such as vases shall be placed on the apparatus.
14. Caution-to prevent electrical shock, match wide blade plug wide slot fully insert.
15. Please keep a good ventilation environment around the entire unit.
16. Always unplug cables by gripping the plug firmly, not by pulling on the cable.
Important Safety Information

Graphite M25 · USB Keyboard Controller
5
ENGLISHFRANÇAISDEUTSCHEESPAÑOLITALIANO
Introduction
Thank you for purchasing the Samson Graphite M25, compact USB keyboard controller!
The Graphite M25 gives you the performance and production control to easily integrate with
Windows or Mac digital production workstations. The keyboard can also be powered directly by
an Apple iPad (using the Apple iPad Camera Connection Kit or Lightning to USB Camera Adapt-
er, not included), and can be used to control many iOS MIDI apps, like GarageBand. To capture
the dynamics of your performance, the Graphite M25 comes equipped with a 25-key veloci-
ty-sensitive keyboard. In addition, the Graphite M25 has four velocity-sensitive trigger pads with
aftertouch, which can be used for recording drum beats, triggering samples, or controlling midi
parameters.
The Graphite M25 also functions as a full-featured control surface with eight knobs, one master
encoder, and transport controls. Four programmable presets provide access to additional layers
of control. To take full advantage of the assignable functions, you will need to download the free
Graphite M25 editor from the Samson website (www.samsontech.com).
In these pages, you’ll find a detailed description of the features of the Graphite M25 keyboard
controller, as well as a guided tour of its control panel, and inst ructions for setup and use.
You’ll also find a warranty card enclosed. Please don’t forget to fill it out and mail it in so that
you can receive online technical support, and so that we can send you updated information
about this and other Samson products in the future.
We recommend you record your serial number in the space provided below, for future refer-
ence.
Serial number: ____________________________________________
Date of purchase: __________________________________________
With proper care and maintenance, your Graphite M25 will operate trouble-free for many years.
Should your keyboard ever require servicing, a Return Authorization (RA) number must be
obtained before shipping your unit to Samson. Without this number, the unit will not be accept-
ed. Please call Samson at 1-800-3SAMSON (1-800-372-6766) for an RA number prior to
shipping your unit. Please retain the original packing materials and, if possible, return the unit
in its original carton. If your Graphite M25 was purchased outside of the United States, contact
your local distributor for warranty details and service information.

Graphite M25 · USB Keyboard Controller
7
ENGLISHFRANÇAISDEUTSCHEESPAÑOLITALIANO
Quick Start
1. Connect the Graphite M25 to your computer or iPad* using the supplied USB cable. The
unit will receive power and transmit MIDI data via the USB connection.
If the Graphite M25 is connected to a non-powered USB hub, it may not receive enough
power to turn on. It is recommended that you connect the Graphite M25 directly to your
computer or to a powered USB hub.
2. Launch your DAW or virtual instrument software.
3. Set the Graphite M25 as the MIDI Input and MIDI Output device.
*To connect directly to an iPad, you will need to use the Apple iPad Camera Connection Kit or
Lightning to USB Camera Adapter (not included).
Computer

10
Editing Parameters
The Graphite M25 features 19 controls which settings can be customized using the Graphite
M25 computer editor, which can be found on the Samson website (www.samsontech.com). The
following information outlines the available parameters for each control that can be adjusted.
Trigger Pads: Note
Note: Sets the MIDI note name that the Trigger Pad will transmit.
MIDI Channel: Sets the specific MIDI channel that the Trigger Pad will use to transmit note data.
Mode: Sets the behavior of the pad. If set to toggle, the pad acts like a switch, sending a note
on message when first pressed, and a note off message when pressed a second time. When set
to momentary, the pad sends a note on message when pressed down and a note off message
when the pad is released.
Trigger Pads: CC
Control Change: Sets the control change number that the Trigger Pad will transmit.
MIDI Channel: Sets the specific MIDI channel that the Trigger Pad will use to transmit control
change data.
Mode: Sets the behavior of the pad to either toggle or momentary.
Transport Controls
Control Change: Sets the control change number and name that the Transport Control button will
transmit.
MIDI Channel: Sets the specific MIDI channel that the Transport Control button will use to
transmit data.
Mode: Sets the behavior of the button to either toggle or momentary.
Assignable Knobs
Control Change: Sets the control change number and name that the knob will transmit.
MIDI Channel: Sets the specific MIDI channel that the knob will use to transmit data.
Master Encoder
Control Change: Sets the control change number that the Master Encoder will transmit.
MIDI Channel: Sets the specific MIDI channel that the Master Encoder will use to transmit data.
Modulation Strip
Control Change: Sets the control change number that the Modulation strip will transmit.
MIDI Channel: Sets the specific MIDI channel that the Modulation strip will use to transmit data.

Graphite M25 · USB Keyboard Controller
11
ENGLISHFRANÇAISDEUTSCHEESPAÑOLITALIANO
Keyboard 25-key, semi-weighted, velocity sensitive
Controls
Encoder 1
Knobs 8
Trigger Pads 4
Transport Controls 5 (Rewind, Fast Forward, Stop, Play, Record)
Ribbon Strips Pitch Bend, Modulation
Key Range Octave +/–
Operation Controls SUSTAIN, CC Mode, PROG, PRESET, PAD
Presets 4
Functions Keys 0-9, Enter
MIDI MIDI over USB
Power USB Bus Power
Accessories USB Cable
Dimensions 14.3” x 6.14” x 1.68”
363 mm x 156 mm x 42.75 mm
Weight 1.43 lbs
.65 kgs
Specications

12
Apple, Mac, Mac OS et iPad sont des marques commerciales appartenant à la société Apple
Inc., déposées aux Etats-Unis et dans d'autres pays.
IOS est une marque de commerce ou marque déposée de Cisco aux Etats-Unis et dans d'autres
pays ; elle est utilisée sous licence.
MISE EN GARDE : POUR DIMINUER LE RISQUE D’ELECTROCU-
TION, NE PAS RETIRER LE CACHE (OU A L’ARRIERE). CE MA-
TERIEL NE COMPORTE PAS DE PIECES SUSCEPTIBLES D’ETRE
REPAREES PAR L’UTILISATEUR. CONFIEZ TOUTES LES INTERVEN-
TIONS D'ENTRETIEN A DES TECHNICIENS DE S.A.V. QUALIFIE.
Le triangle équilatéral renfermant un éclair terminé par une flèche a pour but d’alerter l’utilisa-
teur sur la présence d’une "tension dangereuse" non isolée à l’intérieur du boîtier de l’appareil qui
peut être d’une valeur suffisante pour présenter un risque d’électrocution.
Le triangle équilatéral renfermant un point d’exclamation a pour but d’alerter l’utilisateur sur la
présence de consignes d’utilisation et de maintenance importantes dans la documentation jointe
à l’appareil.
ATTENTION
RISQUE D’ÉLECTROCUTION !
NE PAS OUVRIR !
AVERTISSEMENT
POUR PREVENIR L'INCENDIE OU L'ELECTROCUTION. NE VOUS SERVEZ DE CETTE PRISE
MALE AVEC UNE RALLONGE, UNE PRISE FEMELLE OU AUTRE PRISE DE SECTEUR QUE
SI LES LAMES PEUVENT ETRE ENFONCEES A FOND POUR PREVENIR LEUR EXPOSITION.
POUR PREVENIR L'INCENDIE OU L'ELECTROCUTION. N'EXPOSEZ CET APPAREIL NI A
LA PLUIE, NI A L'HUMIDITE. POUR PREVENIR TOUT RISQUE D'ELECTROCUTION, FAIRE
CORRESPONDRE LA LAME LARGE DE LA FICHE MALE A LA FENTE LARGE DE LA PRISE
FEMELLE, PUIS ENFONCER A FOND.

15
Graphite M25 - Clavier de commande USB
ENGLISHFRANÇAISDEUTSCHEESPAÑOLITALIANO
Introduction
Vous venez d'acquérir le clavier de commande USB compact Samson Graphite M25. Merci! Le
Graphite M25 vous offre performances et maîtrise de la production pour s'intégrer facilement
aux stations de travail de production numérique sous Windows ou Mac. Ce clavier peut être
alimenté directement par un Apple iPad (à l'aide du kit de connexion d'appareil photo pour
Apple iPad ou de l'Adaptateur Lightning vers USB pour appareil photo, non joint à la livraison),
destiné à contrôler de nombreuses applications iOS MIDI, comme GarageBand. Pour restituer
toute la dynamique de votre spectacle, le Graphite M25 est équipé d'un clavier à 25touches
sensible à la vitesse. En outre, le Graphite M25 est équipé de quatre plateaux déclencheurs
sensibles à la vitesse à aftertouch, qui peuvent servir à enregistrer les sons de batterie, à
déclencher des échantillons (samples) ou à régler les paramètres midi.
Le Graphite M25 fonctionne également comme une interface de commande riche en fonction-
nalité à huit boutons, encodeur maître et commandes de défilement. Quatre préréglages
programmables donnent accès à des couches de réglage supplémentaires. Pour profiter pleine-
ment des fonctions programmables, vous devrez télécharger le logiciel d'édition gratuit pour
Graphite M25 sur le site web de Samson (www.samsontech.com)
Vous trouverez ici une présentation détaillée des caractéristiques du clavier de commande
Graphite M25, ainsi qu'une visite guidée de sa façade de commande et les notices d'installa-
tion et d'utilisation. Vous trouverez également ci-joint une carte de garantie. N’oubliez pas de
la remplir et de nous la renvoyer. Vous pourrez ainsi bénéficier de l’assistance technique en
ligne et recevoir les dernières informations sur les produits Samson.
Prenez le temps de noter ci-dessous le numéro de série pour le retrouver ultérieurement.
Numéro de série: ____________________________________________
Date d'achat: _______________________________________________
Avec un entretien adapté et une bonne maintenance, votre Graphite M25 vous donnera satis-
faction pendant de nombreuses années. Pour faire réparer votre panneau de commande, vous
devez tout d’abord obtenir un numéro de retour (RA) avant de le renvoyer à Samson. Sans ce
numéro, l’appareil ne sera pas accepté. N'hésitez pas à appeler Samson au 1-800-3SAMSON
(1-800-372-6766) pour obtenir ce numéro avant de renvoyer votre appareil. Veuillez conserver
les matériaux d’emballage d’origine et, si possible, renvoyer l’appareil dans son carton d’origine.
Si vous avez acheté votre Graphite M25 ailleurs qu'aux Etats-Unis, contactez votre distributeur
pour obtenir tous les renseignements sur la garantie et le service après vente.

16
Caractéristiques
Faisant appel à une technologie dernier cri, le Samson Graphite M25 est conçu jusqu'au
moindre détail. Voici ses principales caractéristiques:
• clavier de 25touches sensible à la vitesse
• réglettes de Modulation de Hauteur et de Modulation
• Quatre plateaux déclencheurs sensibles à la vitesse avec aftertouch (deux rangées) pour
sons de percussions et échantillons
• Mode CC pour régler les plateaux déclencheurs pour envoyer des messages de changement
de réglage
• Huit boutons programmables pour un contrôle direct sur votre DAW et vos instruments
virtuels
• Commandes de défilement
• Quatre préréglages globaux pour un réglage étendu
• Mode Programme pour envoyer des informations sur le changement de programme
• De conception compacte, parfait pour la scène et le studio
• Des boutons spéciaux de Montée / Descente d'un Octave et de Sustinato
• Prêt-à-l'emploi et alimenté par bus via USB
Composants du système
• Clavier USB Samson Graphite M25
• Un (1) câble USB
• Manuel d'utilisation du Graphite M25
Conguration minimale requise
Windows (PC)
• Windows XP/Vista/Win 7/Win 8
• 800MHz ou plus, 256 Mo de RAM ou plus, port USB
Mac OS
• Mac OS X 10.4.9 ou plus
• 733MHz ou plus, 512 Mo de RAM ou plus, port USB
Apple iPad
• iOS v4.2 ou version ultérieure
Product specificaties
Merk: | Samson |
Categorie: | Midi-keyboard |
Model: | Graphite M25 |
Heb je hulp nodig?
Als je hulp nodig hebt met Samson Graphite M25 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Midi-keyboard Samson

10 Oktober 2022
Handleiding Midi-keyboard
- Midi-keyboard Casio
- Midi-keyboard Yamaha
- Midi-keyboard Akai
- Midi-keyboard Alesis
- Midi-keyboard Arturia
- Midi-keyboard Behringer
- Midi-keyboard Icon
- Midi-keyboard Ion
- Midi-keyboard Korg
- Midi-keyboard M-Audio
- Midi-keyboard Medeli
- Midi-keyboard Novation
- Midi-keyboard Peavey
- Midi-keyboard Pinnacle
- Midi-keyboard Pyle
- Midi-keyboard Reloop
- Midi-keyboard Roland
- Midi-keyboard Evolution
- Midi-keyboard CME
- Midi-keyboard Native Instruments
- Midi-keyboard IK Multimedia
- Midi-keyboard Chord
- Midi-keyboard Swissonic
- Midi-keyboard ESI
- Midi-keyboard Keith MCmillen
- Midi-keyboard Motu
- Midi-keyboard Doepfer
- Midi-keyboard Kurzweil
- Midi-keyboard Studiologic
- Midi-keyboard Nektar
- Midi-keyboard Waldorf
Nieuwste handleidingen voor Midi-keyboard

3 Maart 2025

3 Maart 2025

1 December 2024

17 November 2024

28 Mei 2024

28 Mei 2024

28 Mei 2024

28 Mei 2024

7 December 2023

7 December 2023