Salus T105RF Handleiding

Salus Thermostaat T105RF

Lees hieronder de 📖 handleiding in het Nederlandse voor Salus T105RF (3 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

Battery Installation

Your thermostat uses two (2) “AA” size batteries to operate. To power-up

the unit, insert two “AA” batteries into the battery compartment of the

front housing. When power is applied for the ﬁrst time, the display must

show time and the day as well as the room temperature (for example

28.5°C).

If the display is different, press the RESET button. Use a ﬁne probe such

as straightened paper clip to gently push the RESET button.

After installation of the batteries, push back the rear housing to the con-

trol centre and then the stand. Before turning on the main switch of the

system, press the reset button once. The thermostat is ready for use.

BATTERY REPLACEMENT

It is recommended that the batteries be replaced when the display is

showing the battery-low icon. To replace the battery,

1. Turn off the power of the Receiver ﬁrst.

2. Remove the back housing and stand of the Desktop Unit.

3. Replace the old batteries with 2 new AA alkaline batteries.

4. Replace the back housing and stand.

5. Press the reset button once and then turn on the power switch of the

Receiver.

Setting Clock

1. Press the SET TIME button to clear all digits except the day indicator

and the time display. The day indicator is ﬂashing.

2. While day indicator is ﬂashing, press UP or DOWN button to adjust.

3. Press the SET TIME button again, hour digits are ﬂashing instead of

day indicator. Press UP or DOWN button to adjust. Press and hold the

UP or DOWN button to speed up the adjustment rate.

4. Press the SET TIME button again, minute digits are ﬂashing instead

of hour digit. Press UP or DOWN button to adjust. Press and hold the

UP or DOWN button to speed up the adjustment rate.

5. Press the SET TIME button again to return to normal operation

mode.

6. The unit will return to normal operation mode if no key is pressed for

15 seconds.

Setting Control Temperature

1. Press the SET TEMPERATURE button to display the pre-deﬁned set

temperature.

2. Press the CONF/ECON button to toggle between the setting of eco-

nomic mode and comfortable mode.

3. Press the UP or DOWN button to increase/decrease the set tempera-

ture by 0.2°C.

4. Press the SET TEMPERATURE button again to save the set tempe-

rature.

5. The unit will return to normal operation mode if no button is pressed

for 15 seconds.

6. The default setting of comfortable mode is 21°C for heater mode and

23°C for cooler mode. The economic mode is 18°C for heater mode

and 26°C for cooler mode.

SETTING PROGRAM

i) Select Week-Day

1. Press the SET PROGRAM button, the day indicator shows the pro-

gram day and is ﬂashing. Program number indicator shows the current

program for the selected day.

2. Press the UP or DOWN button to select the day needed to program.

You can select the whole week, working day, weekend,or individual

day to program.

Receiver

- Linked with Control Centre via RF.

- Powered by line voltage only. No battery required.

- Two LED indicators for power and output status.

INSTALLATION OF RECEIVER

Caution:

1. The appliance can only be mounted indoors and in areas free from

any water or moisture.

2. A suitable fuse with a rating not exceeding 13A, should be in the power

line.

3. Observe the national regulations for wiring.

4. .gnicivres dna noitallatsni rof dednemmocer si naicirtcele deﬁilauq A

This thermostat has been designed for simple and quick installation

requiring only a few tools. Only the Receiver needs to be installed.

Required Tools

• Hammer • Masking tape • Screwdriver

• Drill and 3/16” drill bit (if not installed on a junction box)

RF Address Code Setting

If there is another user nearby, e.g. in the next house, your receiver

maybe fault triggered by their transmitter. You may select a different RF

address code to prevent this. Receiver can only response to RF coding

with the same address code setting as its own address code.

1. To adjust address code of Control Center Receiver, simply left or right

of the 5 dip switch levers.

2. To adjust address code of Control Centre, open the housing of the

transmitter unit. See battery replacement section on how to open the

housing.

Caution:

1. Address code of Control Centre must be the same as address code

of Receiver. For any on position of address code # in Control Centre,

the same address code # of Receiver must be switched to ON.

2. Disconnect AC power and remove batteries prior to adjusting address

code.

Removing your old thermostat

CAUTION : to avoid electric shock, isolate the power of the heating/

cooling system at the main power box in your home. Read the following

instructions carefully before disconnecting the wires.

1. Turn off your old thermostat.

2. Remove the cover from the old thermostat.

3. Unscrew the old thermostat from the wall plate.

4. Now ﬁnd the screws attaching the wall plate to the wall, and remove

them. You should now be able to pull the wall plate a small distance from

the wall. Do not disconnect any wire yet, simply locate the wires.

WARNING: After removing the wall plate, if you ﬁnd that it is mounted on

a junction box (e.g. a box similar to one behind a light switch or electric

outlet), high voltage circuit may be present and there is a danger of

electric shock. Please consult a qualiﬁed electrician.

T105RF – WIRELESS THERMOSTAT

INTRODUCTION

This thermostat can replace most common residential thermostats and

is designed to be used with electric, gas or oil heating control system or

cooling system. Unlike ordinary single unit design thermostats, this unit

is a new type of thermostat separating the thermostat function into two

units. The Receiver serves for wiring connections and heat/cool on/off

control. The Control Centre serves as user interface and temperature

sensing/control. The two units are linked by RF.

The advantage is that users can put the Control Centre nearby and can

read/control the temperature of the living area.

SPECIFICATION

Clock accuracy: +/ - 60 seconds/month

Temp. measurement: 0°C to 40°C in 0.2°C resolution

Temp. accuracy: +/ - 1°C at 20°C

Temperature Control: 7°C to 30°C in step of 0.2°C

Span: 0.4, 0.8 ,1.4 or 1.8°C

Air conditioner cycle time: 3 minutes

Operation temperature: 0°C to 40°C

Storage temperature: -10°C to 60°C

Power Source: Control Centre 2 AA (LR6) batteries

Receiver: 230VAC 50Hz 16A resistive, 5A inductive

Size and Weight: Control Centre 116 x 100 x 23.5mm, 126g

Receiver: 128 x 97 x 37mm, 190g

Frequency: 868 Mhz

Features

Several useful functions and operating modes have been incorporated

to suit a variety of customer needs besides all the features associated

with the state-of-the-art programmable thermostat.

Choosing a Location

Note: for a new installation, choose a mounting location about ﬁve feet

(1.5 metres) above the ﬂoor in an area with good air circulation and

away from:

1. Drafts.

2. Air ducts.

3. Radiant heat from the sun or appliances.

4. Concealed pipes and chimneys.

Mounting the Receiver onto the wall/junction box

1. Remove the back plate from the Receiver.

2. Mark the holes position.

3. Drill two holes and insert the plastic anchors carefully into the holes,

fasten the back plate to the wall with 2 screws.

4. Connect the wires - see wiring diagram.

5. Push on the wires in the wall.

6. Securely fasten the Receiver to the back plate.

WIRING DIAGRAM

RECEIVER WIRING TERMINALS

Terminal Identiﬁer Description

1 NO Normally Open [N/O]

2 COM Linked Live feed (230V AC heating applications

only)

3 L Live feed (230V AC)

4 N Neutral

SETTING OF CONTROL CENTRE

Heater/Cooler Selection

Before making any selection in the

control centre, its back housing must

be removed as follows: Inside the

Control Centre after the back housing

is removed, you can find the DIP

switch.

These three switches are used to

control the span and heat/cool sys-

tem. Set the DIP switch (position 3)

according to your selection of heater

system or cooler system as the fol-

lowing diagram.

Temperature Span Selection

Span is the temperature difference between the turn on temperature

and turn off temperature. For example, in heating systems, if you set

temperature to 20°C and span to 0.8°C, the heater will operate when the

room temperature drops to 19.2°C and turns off when the temperature

rises to 20.8°C. Set the DIP switch (position 1 & 2) according to your

selection of temperature span as the following diagram.

1 2 Span

ON ON 0.4ºC

OFF ON 0.8ºC

ON OFF 1.4ºC

OFF OFF 1.8ºC

Day Indicator

Heat/Cooler On Icon

Comf. Icon

Econ. Icon

Program Number

Manual Override Icon

Up Button

Set Time Button

Reset Button

Clock

Anti-freezing icon

Battery Low Icon

Temperature

Control Proﬁle Bar

Comf/Econ Button

Down Button

Backlight

Set Temperature Button

Set Program Button

On : HeaterOn

Off : Cooler

Remove

the front

housing

Push and hold

internal lock by

a screw driver

back

housing

Align the hinge

front

housing

Control Centre

- Can be placed anywhere in the

home to detect and control the

temperature of an area of the

user’s choice. Not limited by power

control wiring locations.

- Link with the Receiver via RF.

Control distance 70M open site

- LCD shows the “need to know”

information only, which is easier to

understand.

- Real time clock with day of the

week display

- Room temperature display

- Control proﬁle display

- Simpliﬁed temperature adjust-

ment - Simpliﬁed programming

procedure

- 6 pre-deﬁned control proﬁles,

3 user programmable control

proﬁles

- Protection against freezing

- Temporary set-temperature

override

- User selectable temperature

span; User selectable heater/

cooler operation mode

- Slim housing design

- EL backlight

OFF

12345

123

Set the address Code

#1 - #5 to ON or OFF

position

CONTROL CENTRE RECEIVER

NO COM

230V~

50Hz

16(5)A

L N

ANTI-FREEZING MODE

1. Pressing the UP and DOWN buttons simultaneously will activate the

anti-freezing mode (for heater mode only). The ANTIFREEZING icon

and the HAND icon will be turned on while both the COMF and ECON

icon will be turned off.

2. Pressing any button will terminate the antifreezing mode and revert to

normal operation mode.

3. The default set temperature for the anti-freezing mode is 7°C.

BACKLIGHT

Press the BACKLIGHT button to turn on the backlight. The backlight will

switch off when no button is pressed for 15 seconds.

POWER SWITCH

There is a power switch on the Receiver. When there is no demand to

turn on the heating/cooling device, e.g. when you go on holiday, it is

recommended to turn the power switch to the Off position.

LED INDICATOR

There are two LEDs on the Power Control Unit as status indicators:

1. Red LED turns on as long as there is power to the unit. When there is

no power to the unit or when power switch underneath the front cover

is put at the Off position, the red LED is Off.

2. Green LED turns on as long as the heating/cooling device is ener-

gised.

SALUS Controls plc

SALUS House,

Dodworth Business Park South,

Dodworth, Barnsley, S75 3SP

Web: www.salus-tech.com

tceleS )ii Control proﬁle pre-deﬁned

1. Press the SET PROGRAM button again, the day indicator stops ﬂas-

hing and the program number starts ﬂash.

2. Press the UP or DOWN button to select the program proﬁle. P1-P6

are predeﬁned programs. Their proﬁles are shown as below.

3. If any of these programs are selected, press the SET PROGRAM

button again to conﬁrm this program for the speciﬁed day and return

to normal operation mode.

4. Press the button to toggle the control temperature setting and

advance the setting hour digit by one.

5. Press the “P” button to terminate the setting procedure and to return

to normal operation mode.

6. The setting procedure will terminate automatically when no button is

pressed for 15 seconds.

Program number Program proﬁle

Program 1 :

Factory Preset

“Whole day

Comfort”

Program 2 :

Factory Preset

“Whole day

Econ”

Program 3 :

Factory Preset

“Holiday”

Program 4 :

Factory Preset

“Whole day (A)”

Program 5 :

Factory Preset

“Whole day (B)”

Program 6 :

Factory Preset

“Half-day work”

Testing the RF Transmission Range

1. Press UP button until the setpoint temperature is higher than room

temperature by a few degrees.

2. Wait for a few seconds.

3. Check the green LED. It should be On.

4. If the LED is not On, try to place the Control Centre closer to the Re-

ceiver. Press the Down button to adjust the setpoint temperature to

be lower than room temperature to “turn off” the receiver.

5. Repeat steps 1 to 3.

6. The receiving range between Control Centre and Receiver is 70M in

open area. When placed indoors, this distance may be shorter because

of blocking by concrete walls etc, but is enough for most household

applications.

7. Press RESET button after receiving range testing.

TEMPORARY OVERRIDE

Override the Operation Mode

At the normal operation mode, press the CONF/ECON button to toggle

the current set temperature to comfortable mode or economic mode. If

the operation mode is being overriden, the HAND icon will be turned on

with the current operation mode icon.

Override the Setting Temperature

1. In the normal operation mode, the current set temperature can be

overriden by pressing the UP or DOWN button. When in override, the

new set temperature will be displayed with turning the HAND icon on

and both the CONF and ECON icons off.

2. Press any button (except the UP or DOWN button), this will terminate

the setting procedure and will revert back to normal mode with the

new setting.

3. The unit will revert to normal operation mode automatically when no

button is pressed for 15 seconds.

IM-SARV105-GB-01

SALUS 2-Year Guarantee

SALUS Controls guarantees to you, as purchaser, that the enclosed

product will be free from defects in material, workmanship or design

under normal use or service for a period of 2 years.

This guarantee is not assignable. Our liability to you, under this

guarantee is limited to repairing or replacing any part which we find

to be defective in material, workmanship or design, free of charge to

the customer,upon sending the product with proof of date of purchase,

postage paid to SALUS Controls plc, SALUS House, Dodworth

Business Park, Whinby Road, Dodworth, Barnsley S75 3SP.

The terms of this guarantee will not apply in the following

circumstances: if the product has been modified, dismantled,

contaminated, damaged,neglected or otherwise abused or altered

following the date of purchase, or if it fails to operate due to incorrect

siting, installation, maintenance or inadequate or over voltage AC

electical power, or damage caused by failure to abide by the

instructions supplied.

The liability of SALUS Controls plc, arising from the sale of this

product or under the terms of this guarantee shall not in any case

exceed the cost of replacement of the product. In no case, shall

SALUS Controls plc be liable for consequentail loss or damage

resulting from the failure of the product or the breach of this or any

other guarantee, express or implied or damage caused by failure to

abide by the instructions supplied.

This guarantee does not affect your statutory rights.

Tel: +44 (0) 1226 323961

Product specificaties

Merk:	Salus
Categorie:	Thermostaat
Model:	T105RF

Heb je hulp nodig?

Als je hulp nodig hebt met Salus T105RF stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Salus

Salus SQ610BRF Handleiding

8 Augustus 2024

Salus IT800 WIFI Handleiding

9 Juli 2024

Salus PH60-1 Handleiding

24 April 2023

Salus HTRS 230 Handleiding

24 April 2023

Salus ST320 Handleiding

24 April 2023

Salus RT300 Funk Handleiding

24 April 2023

Salus RT520RF Handleiding

24 April 2023

Salus RT500 Handleiding

24 April 2023

Salus EP210 Handleiding

24 April 2023

Salus RT510RF Handleiding

24 April 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Tru Components TCN4S-24R Handleiding

18 December 2024

Tru Components TK4S-14RC Handleiding

18 December 2024

Tru Components TX4S-14R Handleiding

17 December 2024

Warmup 5iE Handleiding

16 December 2024

Warmup +Kit Handleiding

16 December 2024

Nobo Connect SWT-IZW Handleiding

15 December 2024

Nobo Connect SWT-IZB Handleiding

11 December 2024

Hive Thermostat Handleiding

10 December 2024

GENERAL Life HT15S Handleiding

9 December 2024

GENERAL Life HT15 Handleiding

9 December 2024