Ryobi P330 Handleiding
Ryobi
Nietmachine
P330
Lees hieronder de 📖 handleiding in het Nederlandse voor Ryobi P330 (36 pagina's) in de categorie Nietmachine. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/36
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
15 GA FINISH NAILER
CLOUEUSE DE FINITION DE CALIBRE 15
CLAVADORA DE ACABADO CALIBRE 15
P330
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
AVERTISSEMENT :
Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
TABLE OF CONTENTS
General Power Tool
Safety Warnings 2-3 ..............................
Nailer Safety Warnings 3-5 ....................
Symbols 6 ..............................................
Glossary 7 .............................................
Features 8 ..............................................
Assembly ............................................8
Operation .......................................8-11
Troubleshooting ................................11
Maintenance .....................................12
Illustrations ..................................13-15
Parts Ordering
and Service Back page ........................
TABLE DES MATIÈRES
Avertissements de sécurité générales
relatives aux outils électriques 2-3 ........
Avertissements de sécurité
relatifs cloueuse de finition 3-5 .............
Symboles 6 ............................................
Glossaire 7 .............................................
Caractéristiques 8 .................................
Assemblage ........................................8
Utilisation ......................................8-11
Dépannage .......................................11
Entretien ...........................................12
Illustrations ..................................13-15
Commande de pièces
et dépannage Page arrière ...................
ÍNDICE DE CONTENIDO
Advertencias de seguridad
para herramientas eléctrica 2-3 ...........
Advertencias de clavadora
de acabado 3-5 ....................................
Símbolos 6 ............................................
Glosario de términos 7 .........................
Características 8 ...................................
Armado ..............................................8
Funcionamiento ........................... 8-11
Corrección de problemas 11 ................
Mantenimiento .................................12
Illustraciones .............................. 13-15
Pedidos de piezas
y servicio Pág. posterior .......................
SAVE THIS MANUAL FOR
FUTURE REFERENCE
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
2 — English
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the
risk of electric shock.
vvUse this product only with batteries and chargers
listed in tool/appliance/battery pack/charger
correlation supplement 987000-432.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not wear loose clothing or jewellery. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
3 — English
GENERAL POWER TOOL SAFETY WARNINGS
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
BATTERY TOOL USE AND CARE
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
When servicing a power tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
Always assume that the tool contains fasteners.
Careless handling of the nailer can result in unexpected
firing of fasteners and personal injury.
Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the fastener
causing an injury.
Do not actuate the tool unless the tool is placed firmly
against the workpiece. If the tool is not in contact with
the workpiece, the fastener may be deflected away from
your target.
Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the nailer may be accidentally activated if it is
plugged in.
Use caution while removing a jammed fastener. The
mechanism may be under compression and the fastener
may be forcefully discharged while attempting to free a
jammed condition.
Do not use this nailer for fastening electrical cables.
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
Hold power tool by insulated gripping surfaces, when
performing an operation where the nail may contact
hidden wiring. Nails contacting a “live” wire may make
exposed metal parts of the power tool “live” and could
give the operator an electric shock.
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
power tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
Always wear eye protection with side shields marked
to comply with ANSI Z87.1. Everyday glasses have only
impact resistant lenses. They are not safety glasses.
Following this rule will reduce the risk of serious personal
injury.
Eye protection which conforms to ANSI specifications
and provides protection against flying particles both
from the FRONT and SIDE should ALWAYS be worn
by the operator and others in the work area when
loading, operating or servicing this tool. Eye protection
is required to guard against flying fasteners and debris,
which could cause severe eye injury.
The employer and/or user must ensure that proper
eye protection is worn. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety
glasses that provide protection against flying particles
both from the front and side. Always use eye protection
which is marked to comply with ANSI Z87.1.
Additional safety protection will be required in some
environments. For example, the working area may
include exposure to noise level which can lead to hearing
damage. The employer and user must ensure that any
NAILER SAFETY WARNINGS
Product specificaties
| Merk: | Ryobi |
| Categorie: | Nietmachine |
| Model: | P330 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ryobi P330 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Nietmachine Ryobi
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
15 Juli 2024
17 April 2023
Handleiding Nietmachine
- Nietmachine Bosch
- Nietmachine DeWalt
- Nietmachine Whirlpool
- Nietmachine Einhell
- Nietmachine Fellowes
- Nietmachine Gude
- Nietmachine Hikoki
- Nietmachine Hitachi
- Nietmachine Holzmann
- Nietmachine Iluv
- Nietmachine Kensington
- Nietmachine Leitz
- Nietmachine Makita
- Nietmachine Meister
- Nietmachine Metabo
- Nietmachine Milwaukee
- Nietmachine Parkside
- Nietmachine Powerfix
- Nietmachine Powerplus
- Nietmachine President
- Nietmachine Proline
- Nietmachine Sencor
- Nietmachine Silverline
- Nietmachine Targus
- Nietmachine Topcraft
- Nietmachine Vonroc
- Nietmachine Workzone
- Nietmachine Klein Tools
- Nietmachine Rapid
- Nietmachine Genesis
- Nietmachine Fieldmann
- Nietmachine Porter-Cable
- Nietmachine Sun Joe
- Nietmachine Rapoo
- Nietmachine Dedra
- Nietmachine MSW
- Nietmachine Craftsman
- Nietmachine Surtek
- Nietmachine Rexel
- Nietmachine Swingline
- Nietmachine Total
- Nietmachine Aqua Joe
- Nietmachine Abac
- Nietmachine CTA Digital
- Nietmachine Meister Craft
- Nietmachine Werckmann
- Nietmachine POWERNAIL
- Nietmachine Neo
- Nietmachine Syscom
- Nietmachine Mannesmann
- Nietmachine Smart365
Nieuwste handleidingen voor Nietmachine
16 December 2024
6 December 2024
3 December 2024
3 December 2024
15 Oktober 2024
27 Augustus 2024
28 Juni 2024
25 Juni 2024
25 Juni 2024
24 Juni 2024