Roland XI-MADI Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Roland XI-MADI (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 209 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES”
on back side. After reading, keep the document(s) including those sections where it will be
available for immediate reference.
* 5100044931- 01*
Installing the Expansion interface
Install the expansion interface on a compatible device.
Important Notes on Handling
To avoid the risk of damage to internal components that can be caused by static electricity,
please carefully observe the following whenever you handle the expansion interface.
• Before you touch the expansion interface, always rst grasp a metal object (such as a
water pipe), so you are sure that any static electricity you might have been carrying
has been discharged.
• When handling the expansion interface, grasp it only by the panel or the expansion
interface’s edges. Avoid touching any of the electronic components or connectors.
• Before you connect any cables, make sure they do not carry a static electricity charge.
Such charges can be transmitted, for example, if the other end of the cable has been
in contact with a carpet (or other object) where there is a static electricity buildup.
• Save the bag in which the expansion interface was originally shipped, and put the
expansion interface back into it whenever you need to store or transport it.
Installing
NOTE
• Before installing the expansion interface, you must rst always turn o the unit where
installing and unplug its power cord from the power outlet.
• When restarting the device with the expansion interface installed, wait several
seconds before turning on the power.
1. Loosen the EXPANSION SLOT mounting screws (2) on the device where you’re
installing, and detach the panel cover.
2. Insert the expansion interface into the EXPANSION SLOT.
* Do not touch any of the expansion interface pathways or connection terminals.
* Never use excessive force when installing a expansion interface. If it doesn’t t properly
on the rst attempt, remove the expansion interface
and try again.
3. Secure the expansion interface in place using the mounting screws (2).
Panel Descriptions
1 2
3
2
3
No. Name Explanation
1 VIDEO SYNC IN
connector
This is for input of a black-burst signal.
Here you connect a black-burst generator or other such external
source device when synchronizing the XI-MADI-compatible device
to video equipment.
2 MADI IN/OUT
connectors 1, 2
(optical)
These are optical-type connectors for MADI input and output.
* When no cable is used, attach the connector cap to prevent
entry by dust or other foreign matter. The unit is shipped from
the factory with the connector caps attached to the connectors.
About optical cables
• Use multi-mode ber-optic cable having a core diameter or
50/125 μm or 62.5/125 μm.
• Cable length can be up to 2,000 meters per cable.
• Use SC connectors compliant with ISO/IEC 9314-3.
3 MADI IN/OUT
connectors 1, 2
(coaxial)
These are BNC-type connectors for MADI input and output.
About coaxial cables
• Use cables whose impedance is 75 Ω.
• Cable length can be up to 100 meters per cable.
• Use BNC-type connectors compliant with IEC 60169-8.
• Canare L-5C2VS cable or equivalent is recommended.
Main Features
MADI (Multichannel Audio Digital Interface) is a transmission standard for digital audio
standardized by AES. An extension of the AES/EBU standard for stereo (two-channel)
transmission, it permits transmission of up to 64 channels over a single cable.
The main features of the XI-MADI are as follows.
• Equipped with two types of MADI connectors: optical and BNC
Optical and BNC (coaxial) MADI connectors are provided. You can select separate
connectors for both MADI 1 and MADI 2.
* When signals on the same channel are input via both the optical connector and the
BNC connector, the BNC input takes priority.
* Once optical input has been selected, the system does not switch to BNC as long as
an optical signal continues to be input.
* Depending on the equipment in which the XI-MADI is installed, locking input to
optical or BNC might be possible.
• Support for redundant main and backup transmission
Using a MADI 1 connector as main and a MADI 2 connector as backup is possible. In the
event of a problem with the main connection, the system automatically switches to the
backup connection.
* Redundant transmission uses either all-optical or all-BNC connections. Redundant
transmission combining optical with BNC is not supported.
• Equipped with a VIDEO SYNC IN connector
A VIDEO SYNC IN connector allowing black-burst signal input is provided. Selecting
the VIDEO SYNC IN connector as the clock source enables synchronization with video
equipment.
* For information on the equipment in which the XI-MADI can be installed, check the
following Roland website.
http://proav.roland.com
Thank you, and congratulations on your choice of the XI-MADI expansion
interface.
Installing this expansion interface card in professional audio equipment
from Roland makes it possible to expand audio input and output using
MADI (Multichannel Audio Digital Interface).
For information on devices on which the XI-MADI expansion interface
can be installed, check the Roland website.
http://proav.roland.com
Setup Guide
Copyright © 2015 ROLAND CORPORATION
Main Specications
Channels Up to 64 channels input/output x 2 (48 kHz, 44.1 kHz, 64 ch mode)
Up to 32 channels input/output x 2 (96 kHz, 64 ch mode)
* The number of available channels will be changed by the device that
attach the XI-MADI.
Signal
Processing
Sampling Frequency 96 kHz, 48 kHz, 44.1 kHz
MADI channel mode 64 ch, 56 ch
Data Length 24 bits
Connectors Coaxial MADI IN (1, 2) connectors BNC type
Coaxial MADI OUT (1, 2) connectors BNC type
Optical MADI IN/OUT (1, 2)connectors SC duplex multi mode type (*1)
VIDEO SYNC IN connector BNC type
USB COMPUTER port
(Inside of the panel, updates only)
USB type B
Power
Consumption 7.0 W
Dimensions 120 (W) x 185 (D) x 40 (H) mm
4-3/4 (W) x 7-5/16 (D) x 1-5/8 (H) inches
* Protruding parts not included.
Weight 250 g
9 oz
Operation
Temperature
+5 to +40 degrees Celsius
+41 to +104 degrees Fahrenheit
Accessories Setup Guide, Ferrite core x 5
(*1): For single mode type, consult your Roland vendor.
* In the interest of product improvement, the specications and/or appearance of this unit
are subject to change without prior notice.
Attaching Ferrite Cores
Attach ferrite cores to cables connected to the MADI IN/OUT connectors (coaxial) or VIDEO
SYNC IN connector.
* The ferrite cores are needed to prevent electromagnetic noise. Be sure to attach ferrite
cores to any cables connected to the MADI IN/OUT connectors (coaxial) or the VIDEO
SYNC IN connector.
1. Open an included ferrite core by spreading apart the tabs at two places.
2. Attach the ferrite core at a location near the plug base.
Close the ferrite core by pressing down on each tab until it clicks into place.
MEMO
Connect the plug at the end where the ferrite core is attached to the connector on the
other device.
WARNING
Do not disassemble or modify by yourself
Do not carry out anything unless
you are instructed to do so in the
Setup Guide. Otherwise, you risk
causing malfunction.
Do not repair or replace parts by yourself
Refer all servicing to your retailer,
the nearest Roland Service
Center, or an authorized Roland
distributor, as listed on the “Information.
Do not use or store in the following types of
locations
• Subject to temperature
extremes (e.g., direct sunlight
in an enclosed vehicle, near a
heating duct, on top of heat-
generating equipment); or are
• Damp (e.g., baths, washrooms,
on wet oors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and
shakiness; or are
• Placed in a poorly ventilated location.
Do not allow foreign objects or liquids to
enter unit; never place containers with liquid
on unit
Do not place containers containing
liquid (e.g., ower vases) on this
product. Never allow foreign
objects (e.g., ammable objects,
coins, wires) or liquids (e.g., water
or juice) to enter this product.
Doing so may cause short circuits,
faulty operation, or other malfunctions.
WARNING
Turn o the unit if an abnormality or
malfunction occurs
Immediately turn the unit o,
and request servicing by your
retailer, the nearest Roland Service
Center, or an authorized Roland
distributor, as listed on the “Information”
when:
• Objects have fallen into, or liquid has
been spilled onto the unit; or
• If smoke or unusual odor occurs; or
• The unit has been exposed to rain (or
otherwise has become wet); or
• The unit does not appear to operate
normally or exhibits a marked change in
performance.
Be cautious to protect children from injury
Always make sure that an adult is
on hand to provide supervision
and guidance when using the
unit in places where children are
present, or when a child will be using the
unit.
Do not drop or subject to strong impact
Otherwise, you risk causing
damage or malfunction.
Turn the unit o before installing expansion
interfaces
Before installing the expansion
interface (XI-MADI), you must rst
always turn o the unit where
installing and unplug its power
cord from the power outlet.
CAUTION
Route all cables in such a way as to prevent
them from getting entangled
Injury could result if someone were
to trip on a cable and cause the
unit to fall or topple.
Avoid climbing on top of the unit, or placing
heavy objects on it
Otherwise, you risk injury as the
result of the unit toppling over or
dropping down.
Disconnect all cords/cables before moving
the unit
Damage or malfunction may result
if you fail to disconnect all cables
before moving the unit.
Install expansion interface(s) only in
specied units
Install the expansion interface only
into the specied unit (a device
compatible with the XI-MADI).
Remove only the specied screws
during the installation.
Keep small items out of the reach of children
To prevent accidental ingestion of
the parts listed below, always keep
them out of the reach of small
children.
• Included Parts
Ferrite core
• Removable Parts
Connector cap
Screws
USING THE UNIT SAFELY IMPORTANT NOTES
Placement
• This unit may interfere with radio and
television reception. Do not use this unit in
the vicinity of such receivers.
• Noise may be produced if wireless
communications devices, such as cell
phones, are operated in the vicinity of this
unit. Such noise could occur when receiving
or initiating a call, or while conversing.
Should you experience such problems, you
should relocate such wireless devices so
they are at a greater distance from this unit,
or switch them o.
• When moved from one location to another
where the temperature and/or humidity is
very dierent, water droplets (condensation)
may form inside the unit. Damage or
malfunction may result if you attempt to use
the unit in this condition. Therefore, before
using the unit, you must allow it to stand for
several hours, until the condensation has
completely evaporated.
• Do not place containers or anything else
containing liquid on top of this unit. Also,
whenever any liquid has been spilled on the
surface of this unit, be sure to promptly wipe
it away using a soft, dry cloth.
Maintenance
• Never use benzine, thinners, alcohol or
solvents of any kind, to avoid the possibility
of discoloration and/or deformation.
Additional Precautions
• Use a reasonable amount of care when using
the unit’s buttons, sliders, or other controls;
and when using its jacks and connectors.
Rough handling can lead to malfunctions.
• When disconnecting all cables, grasp the
connector itself—never pull on the cable.
This way you will avoid causing shorts, or
damage to the cable’s internal elements.
• To prevent malfunction and equipment
failure, always turn down the volume, and
turn o all the units before making any
connections.
Intellectual Property Right
• MMP (Moore Microprocessor Portfolio)
refers to a patent portfolio concerned with
microprocessor architecture, which was
developed by Technology Properties Limited
(TPL). Roland has licensed this technology
from the TPL Group.
• This product contains eParts integrated
software platform of eSOL Co.,Ltd. eParts is a
trademark of eSOL Co., Ltd. in Japan.
• Roland is an either registered trademark
or trademark of Roland Corporation in the
United States and/or other countries.
• Company names and product names appearing
in this document are registered trademarks or
trademarks of their respective owners.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
About WARNING and CAUTION Notices About the Symbols
ALWAYS OBSERVE THE FOLLOWING
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
XI-MADI
Audio Interface Module
Roland Corporation U.S.
5100 S. Eastern Avenue Los Angeles, CA 90040-2938
(323) 890-3700
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment requires shielded interface cables in order to meet FCC class B limit.
Any unauthorized changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For C.A. US (Proposition 65)
For Canada
CAN ICES-3 (B)/NMB-3 (B)
For Korea
2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN
For EU Countries
For China


Product specificaties

Merk: Roland
Categorie: Niet gecategoriseerd
Model: XI-MADI
Kleur van het product: Zwart
Gewicht: 250 g
Breedte: 120 mm
Diepte: 185 mm
Hoogte: 40 mm
Aantal: 1
Intern: Ja
Snelle installatiehandleiding: Ja
Compatibiliteit: Roland M-5000
Stroomverbruik (typisch): 7 W
Bedrijfstemperatuur (T-T): 5 - 40 °C
Output interface: BNC

Heb je hulp nodig?

Als je hulp nodig hebt met Roland XI-MADI stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Roland

Roland

Roland PDQ-8 Handleiding

21 December 2024
Roland

Roland PDQ-8S Handleiding

21 December 2024
Roland

Roland CYQ-12 Handleiding

21 December 2024
Roland

Roland PD-9 Handleiding

9 December 2024
Roland

Roland PD-7 Handleiding

9 December 2024
Roland

Roland KDQ-8 Handleiding

9 December 2024
Roland

Roland NEQ-K Handleiding

9 December 2024
Roland

Roland KD-12 Handleiding

9 December 2024
Roland

Roland KD-18 Handleiding

9 December 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd