Roland MDS-Compact Handleiding

Roland Niet gecategoriseerd MDS-Compact

Lees hieronder de 📖 handleiding in het Nederlandse voor Roland MDS-Compact (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

5. Attaching the pad mounts

The tips of the mounts are sharp. Handle them with care.

5–1. Place the stand upright, then loosen the hand knobs

of holders “A” and “B” (two places). Next, spread open

the pipes at left and right.

5–2. Verify that the four vertical pipes are truly vertical.

If the stand wobbles, loosen the bolts on the

holders of curved pipes “L” and “R,” and adjust the

height. After adjusting the height, tighten the

bolts on the holders.

Hand knobs

Holder bolts

5–3. Attach mount holders to the top of the stand and

tighten the respective hand knobs.

Mount holder Mount holder

Hand knobs

5–4. Attach the pad mounts to mount holder, and rmly

tighten the respective hand knobs.

Pad mount

Hand knobs

Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the document(s)

where it will be available for immediate reference.

Roland and V-Drums are registered trademarks of Roland Corporation in the United States and/or other countries.

Owner’s Manual

NOTE

• When setting-up or adjusting the stand, take care not to pinch your ngers between movable parts and the main unit. If using this in a location where children are present, be sure to provide adult supervision or guidance.

• Prepare an area in which you can perform the assembly safely.

• Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws.

* If you will be using this drum stand for an extended period of time in the same location, we recommend that you use a drum mat (TDM series) made by Roland to prevent the rubber feet from soiling the surface on which they are placed.

1. Check the parts

4 5 6 11

No. Name Quantity

1Stand 1

2Curved pipe L 1

3Curved pipe R 1

4Straight pipe L (Long) 1

5Straight pipe R (Short) 1

6Snare pipe 1

7Mount holder 3

8Pad mount 3

9Pad mount (ball type) 1

10 Cymbal mount (Short) 1

11 Cymbal mount (Long) 2

12 Drum key 1

13 Cable clip 4

14 Cable tie 2

2. Assembling the Left and Right Arm Sections

Lay the left and right arm sections on the oor while

assembling them.

2–1. Using a drum key, loosen the bolt on the holder of

straight pipe “L,” then insert curved pipe “L.”

Curved pipe L 2

Straight pipe L 4

Holder

Bolt

2–2. Attach mount holder to straight pipe “L.” Then, after

pulling down straight pipe “L” until it can move no

further, tighten the bolt.

Curved pipe L 2

Straight pipe L 4

Mount

holder

Holder

Bolt

2–3. Using a drum key, loosen the bolt on the holder of

straight pipe “R,” then insert curved pipe “R.”

Curved pipe R 3

Straight pipe R 5

7 cm

Holder

Bolt

2–4. Position straight pipe “R” so that its tip protrudes by

about 7 cm, and then tighten the holder.

3. Attach the Left and Right Arm Sections to

the Main Unit

3–1. Use a drum key to loosen bolt of the holder “A”

(attached to the left-side pipe (with two holders) of

the stand), and insert curved pipe “L” (of the assembly

you created in step 2-1–2-2) into holder “A” of the

stand.

Holder A

Bolt

Curved pipe L 2

Stand 1

As a general rule, insert curved pipe “L” until the

guide hole on the pipe can be seen through the

gap in the holder.

After rmly inserting it all the way, use the drum

key to rmly tighten bolt.

Drum key

Bolt

Guide hole

3–2. Lower holder “B” (attached to the right-side pipe

of the stand) to the same position as holder “C”

(attached to the left-side pipe of the stand).

Holder B

Holder C 7 cm

3–3. Use the drum key to loosen bolt of the holder “B,” and

insert curved pipe “R” (of the assembly you created in

step 2-3–2-4) into holder “B” of the stand.

Holder B

Bolt

Curved pipe R 3

As a general rule, insert curved pipe “R” until the

guide hole on the pipe can be seen through the

gap in the holder.

After rmly inserting it all the way, use the drum

key to rmly tighten bolt.

Guide hole Drum key

Bolt

4. Attaching the snare pipe

4–1. Use the drum key to loosen bolt of the holder “C,” and

insert the snare pipe into holder “C” of the stand. After

rmly inserting it all the way, use the drum key to

rmly tighten bolt.

Insert the end of the snare pipe that doesn’t have

a cap on it into holder “C.”

Holder C

Snare pipe 6

Cap

Bolt

Drum key

WARNING: Caution during setup

When setting-up, you must observe the following cautions.

If you fail to observe these cautions, the stand might overturn or fall, causing injury.

Check for stability when setting-up the stand, and take appropriate care.

Do not spread the stand wider

than 1.2 meters (48 inches).

1.2 m

Adjust the rod height so that

no part of any cymbal is higher

than 1.2 meters (48 inches)

above the oor.

1.2 m

Attach the cymbals in such

a way that the center of the

cymbal does not extend beyond

the rear pipes of the stand.

Center of cymbal must not

extend beyond rear of stand

5–5. Attach pad mount (ball type) to the snare pipe, and

tighten the hand knob.

Pad mount (ball

type) 9

Hand knob

6. Attaching the cymbal mounts

As appropriate for the drum kit that you’re using, attach

the cymbal mounts (short) to the locations for hi-hat

and ride cymbal.

6–1. Insert the two cymbal mounts and the hi-hat mount

into the holders of the curved pipes, and adjust all the

holders as shown in the illustration to complete setup.

“A” type (for hi-hat)

Pad mounts

Pad mount (ball type)

Cymbal mounts (Long)

Cymbal mounts (Short)

“B” type (for ride cymbal)

Pad mounts

Pad mount (ball type)

Cymbal mounts (Long)

Cymbal mounts (Short)

Notes

• When setting up or storing the stand, be careful

not to pinch the ngers you use to handle the

stand.

• Regarding the way of mounting a sound module,

pads, or cymbals, please refer to the owner’s

manual supplied with them.

Product specificaties

Merk:	Roland
Categorie:	Niet gecategoriseerd
Model:	MDS-Compact

Heb je hulp nodig?

Als je hulp nodig hebt met Roland MDS-Compact stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Roland

Roland PDQ-8 Handleiding

21 December 2024

Roland PDQ-8S Handleiding

21 December 2024

Roland CYQ-12 Handleiding

21 December 2024

Roland PD-9 Handleiding

9 December 2024

Roland PD-7 Handleiding

9 December 2024

Roland KDQ-8 Handleiding

9 December 2024

Roland NEQ-K Handleiding

9 December 2024

Roland KD-12 Handleiding

9 December 2024

Roland KD-18 Handleiding

9 December 2024

Roland Graphics Presenter Handleiding

9 December 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Sound Devices A20-Opto Handleiding

11 Januari 2025

Heinner HPM-1000WHCH Handleiding

11 Januari 2025

Sony SU-WB1 Handleiding

11 Januari 2025

Heinner HPM-1300WHBK Handleiding

11 Januari 2025

HiFi ROSE RD160 Handleiding

11 Januari 2025

Philips HTS3610K Handleiding

11 Januari 2025

Philips DLP2810T Handleiding

11 Januari 2025

Silvercrest SMZE 500 C2 Handleiding

11 Januari 2025

Waves L2—UltraMaximizer Handleiding

10 Januari 2025

Digitus DA-70157 Handleiding

10 Januari 2025