Roland KD-A22 Handleiding

Roland Niet gecategoriseerd KD-A22

Lees hieronder de đź“– handleiding in het Nederlandse voor Roland KD-A22 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 240 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
Owner’s Manual
Watch the Quick Start Video
“Installing the KD-A22”
http://roland.cm/kd-a22
Introduction
The KD-A22 can be installed on a 22-inch acoustic bass drum.
Fully assembled view
* A 22-inch acoustic bass drum is not included with this product.
When using a drum stand (MDS-50K/MDS-50KV)
For the MDS-50K/MDS-50KV, the spacing of the bass drum installation area
is as follows.
Vertical: 590 mm (23-1/4”)
Horizontal: 620 mm (24-7/16”)
620 mm
(24-7/16”)
590 mm
(23-1/4”)
Check the Included Items
After opening the package, check that all of the included items are
present. If anything is missing, contact your dealer.
Front head
Batter head
NOTE
Do not pull the cable that is attached to the batter head.
Batter board
NOTE
A circuit board is attached to the batter board. To prevent injury,
damage, or accident, observe the following points.
5
Do not touch the circuit board with your ngers.
5
Do not lay down the batter board with the circuit board facing
downward.
5
Do not apply excessive force to the circuit board.
Batter hoop
* Batter board spacers (6 pcs.) are
already attached
Batter board stopper x 4
Connection cable
Drum key
Before using this unit, carefully read “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (p. 6). After reading, keep the document(s) where it will
be available for immediate reference.
Copyright © 2016 ROLAND CORPORATION
2
Installing the KD-A22
Caution during installation
5
Before you begin the installation procedure, lay down a mat to
protect the oor or the drum from scratches.
5
When turning the bass drum upside down, take care not to drop
it or let it overturn.
5
Muting (such as using weights or a blanket) is not necessary.
Remove such materials from the bass drum. Also, do not install
muting after installing the KD-A22.
1. Attaching the Batter Head
1. Place the bass drum so that the striking surface head is
upward.
2. Loosen the lugs, and remove the hoop and head.
3. Place the batter head on the shell so that the hole in the
batter head is positioned as shown in the illustration.
NOTE
This placement of the batter head assumes that you are using
a single pedal. If you are using a twin pedal, you might need
to adjust the batter head hole position depending on the kick
pedal that you are using. For details, refer to “Using double kick
pedals” (p. 5).
Adjust the position of the batter
head so that the pin is aligned with
the center of the shell as shown in
the illustration.
Hole Pin
Top
Pin
4. Place the batter hoop on the batter head, and adjust the
position of the batter hoop so that the centers of the
batter hoop and batter head are aligned.
Place the batter hoop on the
batter head so that the pedal
attachment hardware is at this
location.
5. Move the batter board spacers attached to the batter
hoop to the positions shown in the illustration.
For a bass drum with eight lugsFor a bass drum with ten lugs
6. Working alternately across opposite sides of the drum,
lightly tighten each lug until the lugs do not wobble.
1
3
4
6
2
8
9
10
57
7. Then tighten each lug another 3/4 of a turn to secure the
batter head.
NOTE
If the batter head is not secured suciently, the sensor might
malfunction, or the sound of the strike might be too loud.
8. Move the batter board spacers attached to the batter
hoop in the directions shown by the arrows, so that they
rmly contact the lugs.
For a bass drum with eight lugsFor a bass drum with ten lugs
3
2. Attaching the Batter Board
1. Align the batter board’s circuit board cover with the hole
in the batter head, and place the batter board.
Hole
Circuit board cover
NOTE
Take care that the batter board’s circuit board cover does not
rest on the batter head or catch on the hole. Forcing it could
damage the circuit board/circuit board cover or the battery
head.
2. As shown in the illustration, align the center of batter
head’s strike surface and center of the batter board hole.
Align the center
Batter board
Striking surface of
the batter head
3. Lightly press down the batter board so that it rmly
contacts the batter head.
Batter board
Batter head
Batter board spacer
Batter hoop
Batter board spacer
3. Attaching the Batter Board Stoppers
Attach the included batter board stopper (4 pcs.) to the batter
hoop.
NOTE
When attaching the stoppers, take care not to hurt your hand
on the lugs.
1. Push down on the batter board stoppers in a location
where your hand will not strike the lug.
Batter board stopper
* It is easier to attach the
stoppers if you spread
them open as shown in the
illustration while pushing
them onto the batter hoop.
Press with the palm of your hand
Grasp this part
with your ngers
2. Position the batter board stoppers as shown in the
illustration.
For a bass drum with eight lugsFor a bass drum with ten lugs

Product specificaties

Merk: Roland
Categorie: Niet gecategoriseerd
Model: KD-A22

Heb je hulp nodig?

Als je hulp nodig hebt met Roland KD-A22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Roland

Roland

Roland PDQ-8 Handleiding

21 December 2024
Roland

Roland PDQ-8S Handleiding

21 December 2024
Roland

Roland CYQ-12 Handleiding

21 December 2024
Roland

Roland PD-9 Handleiding

9 December 2024
Roland

Roland PD-7 Handleiding

9 December 2024
Roland

Roland KDQ-8 Handleiding

9 December 2024
Roland

Roland NEQ-K Handleiding

9 December 2024
Roland

Roland KD-12 Handleiding

9 December 2024
Roland

Roland KD-18 Handleiding

9 December 2024
Roland

Roland Graphics Presenter Handleiding

9 December 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Philips

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024
Philips

Philips Senseo HD7002 Handleiding

24 December 2024
D-Link

D-Link DUB-C2 Handleiding

24 December 2024
Nec

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024
Nec

Nec DS1-TM01 Handleiding

24 December 2024
Profoto

Profoto RFi Softbox Octa Handleiding

24 December 2024
Koenic

Koenic KAP 2523 Handleiding

24 December 2024
Philips

Philips HD9921 Handleiding

24 December 2024
Philips

Philips Senseo HD7008 Handleiding

24 December 2024
Onkyo

Onkyo IRK1804C Handleiding

24 December 2024